Dormakaba 2725-K6 User manual

dormakaba c-lever compact
HBC
08/2017
EN
Technical Manual

dormakaba Schweiz AG
Hofwisenstrasse 24
8153 Rümlang
Switzerland
T: [phone]
www.dormakaba.com
dormakaba Schweiz AG
Mühlebühlstrasse 23
8620 Wetzikon
Switzerland
T: [phone]
www.dormakaba.com
dormakaba EAD GmbH
Albertistrasse 3
78056 Villingen-Schwenningen
Germany
T: [phone]
www.dormakaba.com
Registered in: Heiligenhaus
Copyright © dormakaba 2017
All rights reserved.
No part of this document may be reproduced or used in any form or by any means without prior written permis-
sion of dormakaba Schweiz AG.
All names and logos of third-party products and services are the property of their respective owners.
Subject to technical changes.
08/2017

Technical Manual
308/2017 dormakaba c-lever compact
1 About this document 5
1.1 Target group 5
1.2 Validity 5
1.3 Contents and purpose 5
1.4 Supplementary documentation 5
1.5 Abbreviations/definition of terms 7
1.6 Hazard categories 8
1.7 Notes 8
1.8 Symbols 8
2 Basic safety instructions 9
2.1 Designated use 9
2.2 Product changes 9
2.3 ESD prevention measures 9
2.4 Handling of lithium batteries 10
2.5 Dealing with powerful magnets 10
3 Product description 11
3.1 Overview 11
3.2 Structure 11
3.3 Scope of delivery 12
3.4 Technical data 12
3.4.1 Dimensions 14
3.4.2 Conformity 14
4 Installation 15
4.1 Check minimum distance 15
4.2 Drilling fixing holes 15
4.3 Inserting the battery holder 16
4.4 Additional torsion lock 16
4.5 Securing the battery holder more tightly 17
4.6 Mounting the outside lever handle 17
4.7 Mounting the spindle 18
4.8 Inserting the c-lever into the lock 18
4.9 Mounting the inside rosette and lever handle 18
4.10 Removing the protective film 19
4.11 Switch off 'Bolt Recreation Time' 19
4.12 Dismantling 20
4.12.1 Dismantling the inside rosette and lever handle 20
4.12.2 Removing the inside lever handle from the rosette 20
4.12.3 Removing the c-lever from the lock 20
4.12.4 Removing the battery holder locking screw 20
4.12.5 Removing the outside lever handle 20
5 Programming 21
5.1 Initial programming of MRD components 21
5.2 Master media 21
5.3 User media 21
5.4 Program structures 22
5.5 A/B and B structures 22
5.6 Programming user media with B masters 23
5.7 Deleting individual user media 24
5.8 Deleting individual B masters 25
5.9 Deleting all user media 26

Technical Manual
4 08/2017dormakaba c-lever compact
5.10 INI reset with master media for whitelist and CardLink™ 27
6 Operation 29
6.1 Opening with user media 29
7 Maintenance 30
7.1 Maintenance table 30
7.2 Cleaning 30
8 Service 31
8.1 Replacing the batteries 31
8.2 Connecting the programmer 32
8.3 Configuration and traceback 32
9 Troubleshooting 33
9.1 Error analysis 33
10 Disposal / dismantling 34
10.1 Decommissioning / dismantling 34
10.2 Disposal 34
11 Packaging/return 35
11.1 Complete devices 35
11.2 Electronic component assemblies 35

About this documentTechnical Manual
508/2017 dormakaba c-lever compact
1 About this document
This section contains information for the proper use of this document.
1.1 Target group
This quick start guide is intended for skilled persons only.
The descriptions are intended for skilled persons trained by the manufacturer. The descrip-
tions are no replacement for product training.
For reasons of equipment safety, the installation, maintenance and service measures de-
scribed in this documentation should only be carried out by skilled persons in accordance with
EN 62368-1 (Audio/Video, Information and Communication Technology Equipment – Part 1:
Safety Requirements).
Skilled person is the designation for people who have the appropriate technical training and
experience in setting up the equipment. Skilled persons are expected to use their training and
experience to identify any risks to themselves and others that may arise while carrying out
these activities, and to minimise these risks as far as possible. It is the skilled person’s re-
sponsibility to ensure that the conditions stated by the manufacturer and the applicable regu-
lations and standards are complied with when carrying out these actions.
This documentation is also used to provide information for persons with the following tasks:
• Project planning and project implementation
• Commissioning the product within the network
• Connecting the product to user software by programming customer applications
• Customer-specific adjustments with product parametrisation
1.2 Validity
This document describes the product:
Product designation: c-lever compact
Types: 2724-K6
2725-K6
Article numbers and vari-
ants: 2725-K6 c-lever compact, standard
2724-K6 c-lever compact, half
This document describes all product versions and all optional features and functions. Options
are subject to a charge and therefore only available if purchased.
1.3 Contents and purpose
The contents of these instructions are limited to the installation, operation, maintenance and
servicing of the product.
1.4 Supplementary documentation
The following documents are available from the sales partners:
• Operating manual programmer 1460

About this document Technical Manual
6 08/2017dormakaba c-lever compact
• User manual for programming and signals of the Kaba evolo components
• System description Kaba evolo
• Planning guideline wireless
• Documentation for currently installed system software

About this documentTechnical Manual
708/2017 dormakaba c-lever compact
1.5 Abbreviations/definition of terms
To make this document easier to read, the following short designations are used for the
product designations, as well as the following symbols:
Short designation Product designation
c-lever c-lever compact
evolo component c-lever compact
Programmer Programmer 1460
S-module S-module for c-lever
KEM Kaba evolo Manager
MRD Multi RFID device
Symbols
Acoustic signal
Visual signal

About this document Technical Manual
8 08/2017dormakaba c-lever compact
1.6 Hazard categories
Instructions with information on what to do and not to do to prevent injury and material
damage are denoted specially.
Please follow all hazard instructions. These are intended to help prevent accidents and pre-
vent damage.
These instructions are divided into the following categories:
CAUTION
Low risk
Denotes a potentially dangerous situation that could lead to minor injury.
NOTICE
Important information on the correct use of the product.
Failure to comply with these instructions could lead to malfunctions. The product and/or ob-
jects in the local vicinity could be damaged.
1.7 Notes
Information is denoted by this symbol.
Tips on using the product are useful pieces of information.
They help to make best use of the product and its functions.
1.8 Symbols
Symbols with the following meanings are used for hazards (depending on hazard source.)
General hazard Hazard from electric shock
Risk of explosion Risk to electronic components from
electrostatic discharge

Basic safety instructionsTechnical Manual
908/2017 dormakaba c-lever compact
2 Basic safety instructions
This product has been built to state-of-the-art standards and in line with established safety
regulations. However, hazards for persons and property may arise when handling the product.
Read and observe the following safety instructions before using the product.
2.1 Designated use
This product is intended for use as specified and explained in the Product description section
only. Any other use is considered non-designated use. The manufacturer is not liable for any
damage or injury due to non-designated use. The user/facility operator is the sole person to
bear risks for non-designated use.
2.2 Product changes
NOTICE
No changes should be made to the product, unless in accordance with changes described in
the instructions.
2.3 ESD prevention measures
NOTICE
Risk for electronic components due to electrostatic discharge.
Incorrect handling of electronic PCBs or components can result in damage which will cause a
complete breakdown or sporadic errors.
• General ESD prevention measures must be observed when installing or repairing the
product.
• Wear an anti-static wrist strap when handling electronic components. Connect the end of
the strap to a discharge box or a non-painted, earthed metal component. This way, static
discharges are channelled away from your body safely and effectively.
• Handle a PCB along its edges only. Do not touch the PCB or connectors.
• Place dismantled components on an anti-static surface or in an anti-static shielded con-
tainer.
• Avoid contact between PCBs and clothing. The wrist strap protects PCBs against an elec-
trostatic discharge voltage from the body only. However, damage can also be caused by
an electrostatic discharge voltage from clothing.
• Transport and ship dismantled modules in conductive anti-static bags only.

Basic safety instructions Technical Manual
10 08/2017dormakaba c-lever compact
2.4 Handling of lithium batteries
NOTICE
Lithium batteries can explode or burst explosively.
Improper handling of lithium batteries can lead to fires and explosions.
• Only replace lithium batteries with batteries of the same type.
• Do not open, drill through or squash lithium batteries.
• Do not burn lithium batteries or expose them to high temperatures.
• Do not short circuit lithium batteries.
• Do not recharge lithium batteries.
2.5 Dealing with powerful magnets
WARNING
Magnets can affect the functionality of pacemakers and implanted defibrillators.
The functions of pacemakers or implanted defibrillators may be impaired.
Pacemakers may be inadvertently switched to test mode, causing those who wear them to
feel unwell.
• People wearing such devices should maintain an appropriate distance from magnets.
• People wearing such devices should be warned before approaching magnets.

Product descriptionTechnical Manual
1108/2017 dormakaba c-lever compact
3 Product description
This section provides an overview of the product and gives information on technical details.
3.1 Overview
The c-lever compact is an electronic door fitting complete with an antenna (reading antenna)
and mechatronics unit in the outside shield. After identification using authorised media, the
lock and door can be opened manually. An acoustic and optical signal denotes access author-
isation.
c-lever compact with wireless module and activated wireless function:
the device communicates via wireless gateway with the host system.
The system software determines the supported functions.
See also the wireless planning guideline and instructions for the system software
3.2 Structure
1 2 3 161513 144 6 75 8 9 11 1210
Item Item
1 Inside handle (optional) 9 M2.5x6 battery holder locking
screw
Not included in scope of delivery
2 M6x6 threaded pin (ISO 4029 /
DIN 916) 10 Mechatronics unit with backplate
3 Inside rosette cover (optional) 11 Battery holder
4 Fixing screws for inside rosette
(2 pieces) 12 Opening tool (optional)
5 Inside rosette ‘round’ (optional) 13 Batteries, AAA lithium
(2 pieces)
6 Spindle (square pin) 14 Guide ring
7 Flexible support plate (increases
torque resistance) 15 M6x8 threaded pin (ISO 4029 / DIN 916)
8 Sleeves 16 Outside handle

Product description Technical Manual
12 08/2017dormakaba c-lever compact
3.3 Scope of delivery
• 1 c-lever compact • 2 batteries, AAA lithium
• 1 outside lever handle • Fastening materials
• 1 spindle • 1 drilling template
• 1 handle rosette (optional) • 1 set of instructions
• 1 inside lever handle (optional) • Sleeves
[}4.4]
Overview of backplates
1 2 3 4
Item Backplate designation
1 Sweden (SV) *
2 Finland (FI)
3 Japan (JP)
4 Australia (AU)
*Version described in this document.
3.4 Technical data
Technical data
Connection
Data transfer RFID
Hardware
Lever handle Assorted variants (see
product catalogue)
Fitting Zinc housing HxWxD 122x54x23
Antenna cover Synthetic material
Power supply
Batteries 1.5V, AAA lithium
Ambient conditions 1
Protection type IP54 Outside
Temperature -25°C – +70°C The temperature range de-
pends on the battery manu-
facturer’s specifications.

Product descriptionTechnical Manual
1308/2017 dormakaba c-lever compact
Technical data
Humidity 0%–95% rel. hum., non-con-
densing
Climate Not suitable for heavily cor-
rosive atmospheres (chlorine,
ammonia).
Rooms Not to be used in potentially
explosive environments.
Identification technology
MRD Multi RFID device
LEGIC advant prime
MIFARE DESFire classic
Standards 1
Fire protection DIN 18273 tested in accord-
ance with EN 1634-1
min. EI230-C (EI290-C)
DO 20.31
EN179 According to test certificate
Protection class EN 1906 class 0
Usage class EN 1906 class 3
Cycles
Battery life at 20 °C > 60,000 cycles 1Depending on configuration
Battery life at -20 °C TBD
1Certification not yet complete

Product description Technical Manual
14 08/2017dormakaba c-lever compact
3.4.1 Dimensions
125
52 122,8
54,7
79,4 43,4
23,0
34
5
50°
3.4.2 Conformity
This product conforms to the EU directives
2014/53/EU Radio Equipment Directive
2014/35/EU LVD Directive
2011/65/EU RoHS Directive
You can download the original declaration of conformity in PDF format at www.kaba.com/con-
formity.

InstallationTechnical Manual
1508/2017 dormakaba c-lever compact
4 Installation
This chapter describes the installation of the product.
4.1 Check minimum distance
• Ensure that there is a space of at least 50mm to pull out the battery holder.
>50
4.2 Drilling fixing holes
Replace locks that do not comply with DIN standard 18251-1 (EN 12209: 2015).
The fitting used determines the position, number and diameter of the drill holes.
ø >20 mm
üExisting fitting removed
1. If there are no existing drill holes:
Mark the drill holes on the outside and inside of the door.
2. Remove the lock.
3. Note: Do not drill through the door.
Drill the holes up to the lock mortise.
4. Clean the lock mortise.
5. Insert the lock.

Installation Technical Manual
16 08/2017dormakaba c-lever compact
4.3 Inserting the battery holder
• Insert the battery holder, complete with batteries, into the mechatronics unit.
– The battery holder clicks into place.
– The green light briefly illuminates once.
1x
4.4 Additional torsion lock
• Measure the drill hole diameter on the door.
• Select suitable sleeves to bridge the gap.
• Attach the sleeves.
( )
( )
( )
( )

InstallationTechnical Manual
1708/2017 dormakaba c-lever compact
4.5 Securing the battery holder more tightly
The battery holder can be secured more tightly using a screw.
The screw (M2.5x6) is not included in the scope of delivery.
Use of the battery holder locking screw increases the amount of effort involved in replacing
the batteries, see Dismantling [}4.12].
1.
2. 3.
1. Remove the flexible support plate.
2. Secure the battery holder with the battery holder locking screw (M2.5x6).
3. Attach the flexible support plate.
4.6 Mounting the outside lever handle
1. Position the guide ring on the mechatronics unit.
2. Attach the lever handle in the desired position on the square.
3. Screw the M6x8 threaded pin (with threadlocker) into the lever handle and secure in
place.

Installation Technical Manual
18 08/2017dormakaba c-lever compact
4.7 Mounting the spindle
1. Centre the lug (highlighted in blue) if it is not already central.
8 x 8
8,5 x 8,5
(mm)
2. Align the spindle correctly.
3. Insert the spindle into the mechatronics unit as shown.
ðThe spindle clicks into place.
4.8 Inserting the c-lever into the lock
With the spindle on the outside of the door, push the c-lever through the lock hub.
4.9 Mounting the inside rosette and lever handle
The lever handle can only be removed with a special tool after attaching it to the rosette.
1. 2. 3. 5.
4.
1. Attach the (optional) rosette with the plastic attachment (highlighted in blue) pointing
down. Align the c-lever on the door.
2. Screw the rosette securely in place.

InstallationTechnical Manual
1908/2017 dormakaba c-lever compact
3. Align the cover and place it on the rosette.
4. Attach the lever handle in the desired position on the spindle.
ðThe lever handle locks audibly into place.
5. Screw the lever handle securely in place using the M6x6 pin screw.
4.10 Removing the protective film
• Remove the protective film.
4.11 Switch off 'Bolt Recreation Time'
• Switch off 'Bolt Recreation Time' in the system software and transfer to the device using
the programmer.
Refer to the documentation for currently installed system software.
'Bolt Recreation Time' defines the time interval at which the engaging state of the mechat-
ronics unit should be checked.

Installation Technical Manual
20 08/2017dormakaba c-lever compact
4.12 Dismantling
4.12.1 Dismantling the inside rosette and lever handle
2.
1. 3.
1. Remove the cover from the inside rosette.
2. Loosen the screws.
3. Remove both the lever handle and the rosette.
The lever handle can only be removed with a special tool after attaching it to the rosette.
4.12.2 Removing the inside lever handle from the rosette
• Use spreader forceps to push the circlip apart and simultaneously remove the handle.
4.12.3 Removing the c-lever from the lock
• Pull the c-lever out of the lock hub.
4.12.4 Removing the battery holder locking screw
1.
2.
If present: Remove the battery holder locking screw.
1. Remove the flexible support plate.
2. Unscrew the battery holder locking screw.
4.12.5 Removing the outside lever handle
• Unscrew the threaded pin from the lever handle and remove the lever handle.