Dormakaba STV 1 Series User manual

WN 059507 45532 – 2019-03
EN
STV1xx
Mounting instructions
1 About this manual
1.1 Target group
The door lock STV 1xx must only be mounted by
trained electricians with specific knowledge of
electromechanical locks, fire safety codes and
regulations.
1.2 Intended use
The STV1xx serves to keep doors securely closed, and
to open it without jamming and without delay in case
of emergency. The STV1xx is used in the SafeRoute®
system.
1.3 Other applicable documents:
• System instructions for the used SafeRoute® license
• Operating instructions for the SafeRoute® system
• Inspection logbook
1.4 Symbols used
ATTENTION
This signal word indicates a situation of
potential risk, which could lead to damage
to property or the environment if not
averted.
TIPS AND RECOMMENDATIONS
This signal word indicates useful information
for efficient and trouble-free operation.
1.5 Further labeling
1. 2. Sequence of action steps
6Reference to a chapter
Reference to another document
Door opening direction DIN left =
opening outwards to the right
Door opening direction DIN right =
opening outwards to the left
Components may be damaged by
electrostatic discharges
2 Safety
ATTENTION
Property damage by electrostatic discharge.
The control board may be damaged by an
electrostatic discharge!
• The user must ground his/her own body
before touching a component!
Contents
1 About this manual 1
2 Safety 1
3 Product description 2
4 Mounting 2
5 Assignment of terminals and switches 5
6 Dismantling and disposal 5

3 Product description
The STV 1xx is an electromagnetic lock for swing
doors on escape routes and is mounted on the door
frame. Together with a SafeRoute® Control Unit
(SCU), the door lock forms an escape route security
system. The STV 1xx opens without jamming and
without delay. The maximum locking force complies
with Directive for Electrical Locking Systems on
Escape Route Doors (EltVTR).
They may only be mounted on fire and smoke
protection doors, if the usability certificates for these
doors provide for the mounting, and if the related
requirements are followed. Additional notes can also
be found in the notification “Permitted changes and
supplements to fire protection closures” of the
Deutsches Institut für Bautechnik (DIBt), Berlin.
3.1 Variants
The XX markings are color variants. The instructions
are valid for the STV 101 (silver) and STV 111 (white).
3.2 LED displays
LED on LED off LED flashes
DCW®LED (red)
Bus connection OK
Bus connection interrupted
DCW® error (see SafeRoute®
system instructions)
Config LED (yellow)
Configuration successful
Device not configured
Both LEDs
Configuration mode active
3.3 Technical data
Supply voltage: 24VDC +/-15%
Retention force 2000 N bei Unenn +/- 10 %
Power consumption: locked: 280mA
unlocked: 20mA
Temperature range: -10°Cto+55°C
Rel. Humidity: up to 93%
(non condensing)
Degree of protection: IP 30
4 Mounting
TIPS AND RECOMMENDATIONS
The mounting is only shown on a door which
opens outwards to the left (DIN right).
• Proceed in mirror-inverted order when
mounting a DIN left door.
2STV1xx 2019-03
WN 059507 45532
dormakaba Mounting instructions Product description

3
12
DIN left =
opening
outwards
to the right
DIN right =
opening
outwards
to the left
3STV1xx 2019-03WN 059507 45532
dormakaba Mounting instructions Product description
4
Drilling template

7
1.
4.
2. 3.
5.
5.
5
4STV1xx 2019-03
WN 059507 45532
dormakaba Mounting instructions Product description
2,9x25
d=2,2 mm
x
5
x
mm 1 x 3 mm / 2 x 1 mm
43
44 1 x 1 mm
45 2 x 1 mm
46 1 x 3 mm
47 1 x 1 mm / 1 x 3 mm
48 2 x 1 mm / 1 x 3 mm 2 x
1.
2.
2.
6
1.
1.
2.
5

5STV1xx 2019-03WN 059507 45532
dormakaba Mounting instructions Assignment of terminals and switches
5 Assignment of
terminals and
switches
Config LED
(yellow)
DCW®-LED
(red)
X1
A
1
3
B
24VDC
GND
DCW®-Bus SCU-xx
X2 internal holder contact
X3 internal function
X4 internal door contact
S1 Housing tampering contact
S2 DIP switch for setting the component
addresses (see SafeRoute® system
instructions)
DCW®
address
Switch S2
1
2
3
4
0
1
0
1
0
0
1
1
S3 Service switch for suppression of
tampering alarm
B = Operation (housing tampering
contact activated)
S = service (Housing tampering contact
shut off)
S4 Service button
Press service button for 8 seconds =
original settings
6 Dismantling and
disposal
Dismantling is carried out in reverse order of the
mounting instructions.
The product must not be disposed of in
domestic waste.
The product must be disposed of in an
environmentally friendly manner at the
arranged take-back and collection points.
Refer to the statutory regulations for your country.
Electrostatically
sensitive
components

6STV1xx 2019-03
WN 059507 45532
dormakaba Mounting instructions Assignment of terminals and switches

7STV1xx 2019-03WN 059507 45532
dormakaba Mounting instructions Assignment of terminals and switches

dormakaba Deutschland GmbH
DORMA Platz 1 58256 Ennepetal Germany T: [phone] F: [phone] www.dormakaba.com
Translation of the original manual, subject to change without notice