Dormakaba digital cylinder User manual

dormakaba digital cylinder
1220013692 - 11/2017
EN
Technical Manual

dormakaba Schweiz AG
Mühlebühlstrasse 23
8620 Wetzikon
Switzerland
T: [phone]
www.dormakaba.com
dormakaba Austria GmbH
Ulrich-Bremi-Straße 2
3130 Herzogenburg
Austria
T: [phone]
www.dormakaba.com
Copyright © dormakaba 2017
All rights reserved.
No part of this document may be reproduced or used in any form or by any means without prior written permis-
sion of dormakaba Schweiz AG.
All names and logos of third-party products and services are the property of their respective owners.
Subject to technical changes.
1220013692 - 11/2017

Table of contentsTechnical Manual
31220013692 - 11/2017 dormakaba digital cylinder
Table of contents
1 About this document 5
1.1 Validity 5
1.2 Target group 5
1.3 Contents and purpose 5
1.4 Supplementary documentation 6
1.5 Digital cylinder abbreviations 6
1.6 Hazard categories 6
1.7 Notes 7
1.8 Symbols 7
2 Basic safety instructions 8
2.1 Proper use 8
2.2 Product changes 8
2.3 Use in emergency exit or panic door locks 8
2.4 Areas of use 9
2.5 ESD protective measures 10
2.6 Handling of lithium batteries 10
3 Product description 11
3.1 Overview 11
3.1.1 Structure 11
3.2 Scope of delivery 11
3.2.1 Also for dual digital cylinder 11
3.3 Accessories 11
3.4 Technical data 12
3.4.1 Dimensions 13
3.5 Conformity 16
4 Installation 17
4.1 Requirements 17
4.1.1 Door components 17
4.1.2 Tools required 18
4.2 Installation versions 19
4.2.1 Installation version A 20
4.2.2 Installation version B 22
4.2.3 Function check on anti-panic digital cylinder 24
5 Programming 25
5.1 Initial programming of MRD components 25
5.2 Initial programming of LEGIC® and MIFARE components 25
5.3 Master media 25
5.4 User media 25
5.5 Program structures 26
5.6 A/B and B structures 26
5.7 Programming user media with B masters 27
5.8 Deleting individual user media 28
5.9 Deleting individual B masters 29
5.10 Deleting all user media 30
5.11 INI reset with master media for whitelist and CardLink™ 31
6 Operation 33
6.1 Operating the digital cylinder 33
6.2 Opening with user media 33

Table of contents Technical Manual
4 1220013692 - 11/2017dormakaba digital cylinder
7 Maintenance 34
7.1 Maintenance table 34
7.2 Maintenance of escape doors 34
7.3 Cleaning 35
8 Service 36
8.1 Serial numbers 36
8.2 Replacing the battery 36
8.3 Replace e-module 38
8.4 Disassembling the inner door knob 39
8.4.1 'Click' door knob 39
8.4.2 'Small' inner knob 39
8.5 Configuration and traceback 39
8.6 Reset (INI reset) 39
8.6.1 Reset with master media 40
8.6.2 Reset using programmer 1460 40
8.6.3 Reset using tweezers 40
8.7 Emergency power supply 40
9 Troubleshooting 41
9.1 Error analysis 41
9.2 Error analysis for battery life 43
10 Appendix 44
10.1 Summary of various factors influencing the battery operation 44
10.2 Recommendations for battery operation 44

About this documentTechnical Manual
51220013692 - 11/2017 dormakaba digital cylinder
1 About this document
This section contains information for the proper use of this document.
1.1 Validity
This document describes the product:
Product designation: dormakaba digital cylinder
Types: 143X dormakaba Digital cylinder with Euro profile (17mm)
153X dormakaba Digital cylinder with round profile (22mm)
Article numbers and vari-
ants:
Euro profile cylinder 1435 Standard
1434 Half
1437 Anti-panic
1439 Dual
1431 Asymmetrical
1433 Half with turning range
Round profile cylinder 1535 Standard
1534 Half
1537 Anti-panic
1539 Dual
1531 Asymmetrical
1533 Half with turning range
All versions are available with wireless functionality.
With the exception of the asymmetrical version, all components
are available as ‘protected’ variants (with high anti-drill protec-
tion).
1.2 Target group
This document is intended for specialist personnel only.
The descriptions are tailored to specialist personnel trained by the manufacturer. The descrip-
tions are no replacement for product training.
Service personnel are persons who have the appropriate technical training and experience re-
quired for them to be aware of the risks that could arise for themselves or others when carry-
ing out these activities and to minimise these risks for themselves and others. It is the re-
sponsibility of the service personnel to ensure that the conditions stated by the manufacturer
and the applicable regulations and standards are complied with when carrying out these
activities.
1.3 Contents and purpose
The contents of these instructions are limited to the installation, operation, maintenance and
servicing of the product.

About this document Technical Manual
6 1220013692 - 11/2017dormakaba digital cylinder
1.4 Supplementary documentation
The following documents are available from the sales partners:
• Programmer 1460 technical manual
• Operating manual for programmer 1364
• Wireless operation: Wireless planning guideline
• Documentation for the system software used
1.5 Digital cylinder abbreviations
Short designation Product designation
Digital cylinder dormakaba digital cylinder
Programmer Programmer 1460
1.6 Hazard categories
Instructions with information on what to do and not to do to prevent injury and material
damage are denoted specially.
Please follow all hazard instructions. These are intended to help prevent accidents and pre-
vent damage.
These instructions are divided into the following categories:
DANGER
High risk
Denotes an immediate danger that could lead to serious injury or death.
WARNING
Medium risk
Denotes a potentially dangerous situation that could lead to serious injury or death.
CAUTION
Low risk
Denotes a potentially dangerous situation that could lead to minor injury.
NOTICE
Important information on the correct use of the product.
Failure to comply with these instructions could lead to malfunctions. The product and/or ob-
jects in the local vicinity could be damaged.

About this documentTechnical Manual
71220013692 - 11/2017 dormakaba digital cylinder
1.7 Notes
Information is denoted by this symbol.
Tips on using the product are useful pieces of information.
They help to make best use of the product and its functions.
1.8 Symbols
Symbols with the following meanings are used for hazards (depending on hazard source.)
General hazard Hazard from electric shock
Risk of explosion Risk to electronic components from
electrostatic discharge

Basic safety instructions Technical Manual
8 1220013692 - 11/2017dormakaba digital cylinder
2 Basic safety instructions
This product has been built to state-of-the-art standards and in line with established safety
regulations. However, hazards for persons and property may arise when handling the product.
Read and observe the following safety instructions before using the product.
2.1 Proper use
This product has been designed exclusively for use as set out in the chapter Product Descrip-
tion. Any other use will be deemed improper use. The manufacturer accepts no liability for any
resulting damage. The user/operator bears sole responsibility for the risk.
2.2 Product changes
NOTICE
No changes should be made to the product, unless in accordance with changes described in
the instructions.
2.3 Use in emergency exit or panic door locks
WARNING
Risk of personal injury or death.
• Improper use or incorrectly installed digital cylinders can lead to emergency exit locks or
panic door locks and doors not opening.
• The use of a digital cylinder must be checked carefully before using it in locks with a panic
function.
• Before installing the digital cylinder in an escape door, a check must be carried out to en-
sure that the function of the lever handle or the panic push bar is not obstructed by the
inside knob.
• The use of a digital cylinder in emergency exit locks in accordance with EN179 or in panic
door locks in accordance with EN1125 is documented in the lock manufacturers' perform-
ance declarations. If the digital cylinder is not listed in the performance declarations or
certificates from the lock manufacturer or the lock does not comply with these standards,
an EC conformity inspection of the lock, digital cylinder, fitting and assembly accessories
as one unit must be carried out.

Basic safety instructionsTechnical Manual
91220013692 - 11/2017 dormakaba digital cylinder
2.4 Areas of use
IP56
When used outdoors, the cylinder must be protected against sustained rainfall using a
weather guard.
NOTICE
Freezing liquids can disrupt the function, resulting in doors not opening. No water, therefore,
should get into the cylinder. When used externally, the cylinder must be protected against
sustained rainfall using a weather guard.
When used in fire protection doors, escape routes or rescue routes, the locally applicable
guidelines and building regulations must be observed.
NOTICE
Doors at risk of forced entry
• The following points must be observed for certification as per VdS Class B: On doors at
risk of forced entry, the 'Protected' version of the digital cylinder must be protected with
a VdS-recognised burglary-resistant Class B or C doorplate. These doorplates correspond
to DIN 18 257 Class ES 2 or ES 3 and EN1906 Class 3 or 4. The cylinder must protrude no
more than 3 mm beyond the doorplate.
• The user media (keys, badges, etc.) must always be kept safe to ensure only authorised
personnel may gain access. If identification media are lost, the authorisation data must
be blocked and deleted from all cylinders immediately.
NOTICE
Wrong type of lock
The asymmetrical digital cylinder is not permitted to be used in some lock types.
Please refer to the lock manufacturer’s instructions.

Basic safety instructions Technical Manual
10 1220013692 - 11/2017dormakaba digital cylinder
2.5 ESD protective measures
NOTICE
Danger of damage to electronic components from electrostatic discharge.
If electronic printed circuit boards and components are handled incorrectly, damage may oc-
cur which leads to their complete breakdown or sporadic faults.
• When installing and repairing the product, the general ESD protective measures are to be
observed.
• Before starting service or maintenance work on the product, e.g. changing the battery,
briefly touch the door handle. This will safely and effectively conduct charges away from
your body.
• When handling electronic components, wear the ESD wrist strap. Connect the end of the
strap to an ESD socket or an unpainted, earthed metal component. This will safely and ef-
fectively conduct charges away from your body.
• Only handle the edges of printed circuit boards. Do not touch printed circuit boards or
connecting plugs.
• Put removed components on an anti-static surface or in an anti-static shielding container.
• Avoid contact between printed circuit boards and clothing. The wrist strap only protects
the printed circuit boards from static electricity on the body. Damage can still occur due
to static electricity on clothing.
• Only transport and ship removed modules in ESD-shielding, conductive protective con-
tainers.
2.6 Handling of lithium batteries
NOTICE
Lithium batteries can explode or burst explosively.
Improper handling of lithium batteries can lead to fires and explosions.
• Only replace lithium batteries with batteries of the same type.
• Do not open, drill through or squash lithium batteries.
• Do not burn lithium batteries or expose them to high temperatures.
• Do not short circuit lithium batteries.
• Do not recharge lithium batteries.

Product descriptionTechnical Manual
111220013692 - 11/2017 dormakaba digital cylinder
3 Product description
This section provides an overview of the product and gives information on technical details.
3.1 Overview
The digital cylinder is an electronic locking cylinder with a reader antenna on the rotary knob.
Depending on the version, the reader antenna may be on the outer knob or on both the outer
and inner knob. The security-related electronics are installed behind the anti-drill protection in
the rotor. After identification using authorised media, the lock and door can be opened manu-
ally. An acoustic and optical signal denotes access authorisation.
3.1.1 Structure
2
3
6
7
11
12
13
89
10
5
4
1
1 Outer knob 8 Securing shackle
2 Cover with light ring 9 LA, length on outer side
3 Door knob module with antenna 10 LB, length on inner side
4 Battery 11 Cylinder housing
5 Contact protection film 12 Cam
6 O-ring, Ø 15 x 1mm 13 Inner knob
7 MC insert
Table1: Structure – Description of standard version
3.2 Scope of delivery
• 1 digital cylinder
• 1 forend locking stud
• 1 battery, CR2 lithium type
• 1 set of instructions
3.2.1 Also for dual digital cylinder
• 1 battery, CR2 lithium type
3.3 Accessories
• Relevant system software and programming tools

Product description Technical Manual
12 1220013692 - 11/2017dormakaba digital cylinder
3.4 Technical data
The digital cylinder is intended for use in building doors that are equipped with a lock.
Technical data
Dimensions
Outer knob Ø x L 36 x 45mm
Inner knob Ø x L 36 x 29mm
Small inner knob Ø x L 30 x 27mm
Dual inner knob Ø x L 36 x 45mm
Backset 35mm Door opens inwards
(all variants)
30mm Door opens outwards
(standard inner knob)
35mm Door opens outwards
(dual inner knob)
25mm Door opens outwards
(small inner knob)
Power supply
Battery 3V, CR2 lithium
Radio interface
Technology IEEE802.15.4
Frequency band 2400 to 2485.5MHz
Transmission power + 8dBm
Receiver sensitivity - 102dBm @ 1% PER
Ambient conditions
Protection type IP56 Outer knob (standard)
Temperature -25°C – +70°C The temperature range de-
pends on the battery manu-
facturers' specifications.
Humidity 0%–95% rH, non-condensing
Climate Not suitable for heavily cor-
rosive atmospheres (chlorine,
ammonia).
Rooms Not to be used in potentially
explosive environments.
Standards
VdS ‘Protected’ version:
class BZ+
Classification according to
EN15684 Place:
Classification:
1 2 3 4 5 6 7 8
1 6 B 4 A F 3 2
Resistance to fire EN 1634-2: 95min Version 1439 and 1539 from
total length 85mm
Durability > 200,000 cycles
EN 1303 class 6
EN 179/EN 1125 class 7

Product descriptionTechnical Manual
131220013692 - 11/2017 dormakaba digital cylinder
Technical data
Corrosion DIN EN 1670 class 3
DIN EN ISO 6988, severity
level 3 (SO2 test)
Dimensions DIN18252 Profile cylinder
SN-EN1303 Round profile cylinder
Cycles
Battery life at 20°C Approx. 50,000 cycles Dependent on the configura-
tion used
Battery life at -20°C EXT version:
approx. 40,000 cycles
3.4.1 Dimensions
The dimensions stated also apply for the 22mm round profile cylinder.
45 29
32
1431
3 4
36
36
9,2
25 LB
M5
Dimension drawing 1431 Asymmetrical (profile cylinder)

Product description Technical Manual
14 1220013692 - 11/2017dormakaba digital cylinder
45
32
M5
LA3 10.5
36
1434
Dimension drawing 1434 Half with outer knob profile (profile cylinder)
45 29
32
M5
LA
1435
3 4LB
36
36
Dimension drawing 1435 Standard (profile cylinder)

Product descriptionTechnical Manual
151220013692 - 11/2017 dormakaba digital cylinder
45 27
26
M5
LA3 3.5LB
30
32
36
1437
Dimension drawing 1437 Anti-panic, small inner knob version (profile cylinder)
45
32
M5
LA3 3LB
45
36
1439
Dimension drawing 1439 Dual (profile cylinder)

Product description Technical Manual
16 1220013692 - 11/2017dormakaba digital cylinder
3.5 Conformity
This product conforms to the EU directives
2014/53/EU Radio Equipment Directive
2014/35/EU LVD Directive
2011/65/EU RoHS Directive
You can download the original declaration of conformity in PDF format at www.kaba.com/con-
formity.

InstallationTechnical Manual
171220013692 - 11/2017 dormakaba digital cylinder
4 Installation
This chapter describes the installation of the product.
4.1 Requirements
4.1.1 Door components
Locking cylinder
The locking cylinder with Euro profile or round profile can be used in any door made from
wood, glass or metal, in accordance with the cylinder perforations.
A notch is required for the locking cylinder with the anti-panic round profile cylinder as this
has a pin going all the way through on the inside (LB).
The locking cylinder with the Euro profile cylinder and dual round profile cylinder, in the pro-
tected version (VdS class BZ+) only offers high anti-drill protection on the outside (LA).
WARNING
Risk of personal injury or death.
• Improper use or incorrectly installed digital cylinders can lead to emergency exit locks or
panic door locks and doors not opening.
• The use of a digital cylinder must be checked carefully before using it in locks with a panic
function.
• Before installing the digital cylinder in an escape door, a check must be carried out to en-
sure that the function of the lever handle or the panic push bar is not obstructed by the
inside knob.
• The use of a digital cylinder in emergency exit locks in accordance with EN179 or in panic
door locks in accordance with EN1125 is documented in the lock manufacturers' perform-
ance declarations. If the digital cylinder is not listed in the performance declarations or
certificates from the lock manufacturer or the lock does not comply with these standards,
an EC conformity inspection of the lock, digital cylinder, fitting and assembly accessories
as one unit must be carried out.
NOTICE
Danger of damage to electronic components from electrostatic discharge.
Improper handling can damage or destroy electrostatically sensitive circuit board compon-
ents.
• Observe and apply general ESD protective measures.
Check the dimensions
The following dimensions are to be checked prior to installation:

Installation Technical Manual
18 1220013692 - 11/2017dormakaba digital cylinder
>2 LA LB >2
D
1. Check the door thickness with the fittings (LA and LB)
and the cylinder length.
2. Check the profile cut-out and the backset (D).
• In order for the multitool to be inserted between the knob and the plate, choose cylinder
lengths so as to retain at least a 2mm gap between the plate and the knob.
• In accordance with DIN 18257 for security hardware and security plates, in doors with se-
curity hardware (burglary-resistant fitting) the cylinder housing should not protrude more
than 3mm from the external plate.
• Determine the length of the forend screw: Forend screw ≥ backset + 10mm.
4.1.2 Tools required
• Tool – Multitool
• Allen key, small inner knob, 2mm hex
• Flat head and Phillips screwdriver
• Programming cable
• Adaptor/programming pin

InstallationTechnical Manual
191220013692 - 11/2017 dormakaba digital cylinder
4.2 Installation versions
NOTICE
When installing the lock, there is a risk of being locking out.
Always install the digital cylinder when the door is open. This prevents you from locking your-
self out when using self-locking locks.
The locking cylinder in the digital cylinder version without an inner knob and the dual version
should be programmed before carrying out the function test. After this, hold an authorised
user medium in front of the cylinder and carry out the function test by turning the outer door
knob.
With installation version A, remove the inner door knob and push the cylinder through the fit-
ting and the lock from the outer side of the door.
With installation version B, remove the outer door knob and also the inner door knob if neces-
sary, and push the cylinder housing through the door's lock.
Digital cylinder installation versions
Installation versions
Type A B
1431 Asymmetrical
1435 Standard recommended optional
1433 Half with turning range
1434 Half — optional
1437 Anti-panic recommended optional
1439 Dual — recommended
1531 Asymmetrical
1535 Standard not recommended recommended
1533 Half with turning range
1534 Half — optional
1537 Anti-panic1not recommended optional
1539 Dual — recommended
Key:
1The fitting needs a recess on the inner side for the cylinder pin.

Installation Technical Manual
20 1220013692 - 11/2017dormakaba digital cylinder
4.2.1 Installation version A
1
2
3
1. Remove the outer door knob.
2. Remove the contact protection film.
3. Attach the outer door knob.
4
4. Position the multitool on the outer door knob.
5
5. Turn the multitool to the left and lock it.
The outer door knob and the cylinder housing are now
firmly connected.
6
7
6. Align the cam flush with the cylinder housing.
7. From the outer side of the door, push the digital cylinder
through the fitting and the lock.
8
8. Position the forend locking stud in the lock and tighten it
slightly.
Click!
9
9. Note:
Align the locking spring and the notch with each other!
Place the inner door knob on the cylinder housing.
10
10. Tighten the forend locking stud.