Draco 3514-7R User manual
20.11.2015 Specifications are subject to change for improvement without prior notice.
Operating instructions
1. Intended use. This Power Tool is intended for
industrial applications, for cutting sheet metal
(maximum capacity is indicated in the
Specifications), for use with cutting jaws and
cutting blades which are indicated in these
operating instructions or recommended by
DRÄCO.
2. Do NOT cut sheet metal along welding points. Do
NOT cut multi layer sheets, which exceed the
maximum cutting capacity.
3. Switching ON/OFF the power tool. First check
cable and plug for damage. Slide the switch pad
(5) BACKWARD for switching ON the power
tool. Slide the switch pad (5) FORWARD for
switching OFF the power tool.
4. For inside cutting, the shortest curve possible has
a radius of 45 mm (±1¾”). If cutting a radius with
the right hand, cut from right to left. The outside
radius is unlimited.
5. For cutting out curved or circular inside patterns,
a 14 mm (± 1/2 “) hole, or a punched slot should
be made to insert the centre cutter.
6. If after cutting, a small strip remains this can
easily be trimmed off to the exact measurement,
without leaving a burr or any distortion of the
material. Just one side of the power tools can be
used for cutting also (e.g. along a marked line).
Lift the power tools out of the shavings while the
motor is running. Cut off longer shavings.
7. Both knife and jaws can be sharpened. After
being sharpened or replaced, the knife at it’s
lowest point should protrude the jaws by
approximately 3 mm. The knife should have
approximately 0,05 mm (0,005”) play on each
side of the jaws, centring the cutter with spacing
shims supplied.
8. Every 200 operating ours have the cutting blade
and cutting jaws sharpened at a specialist
workshop.
9. Ensure that the material to be cut is free of oil
and grease.
Care and Maintenance
Warranty
Before working on machine disconnect from power
supply by removing plug from socket.
Always keep the machine and the ventilation slots
clean.
Oil the knife pin and knife at regular intervals.
If the machine should happen to fail despite the care
taken in manufacture and testing, repair should be
carried out by an authorised customer services agent
for DRÄCO power tools
DRÄCO tools carry a guarantee of 12 months from
date of delivery.
Damage attributable to normal wear and tear,
overload or improper handling will be excluded from
the guarantee. (e.g. blades/knifes and jaws)
In case of complaint please send the machine,
undismantled, to your dealer or the DRÄCO Service
Center for electric power tools.
Environmental protection
CE-Declaration of conformity
Recycling raw materials instead of waste
disposal
Machine, accessories and packaging should be sorted
for environment-friendly recycling.
These instructions are printed on recycling paper
manufactured without chlorine
We declare under our sole responsibility that this product is
in conformity with the following standards.
EC 98/37, EC 93/ 68 EWG, EC 04/108 EC, or
standardisation documents DIN EN ISO 12100-1,
DIN EN ISO 12100-2, EN 50 144, EN 55 014
09 Susanne Draenert
Operating Instructions for the Radius-Seam Metal Shear 3514-7R
To avoid any disturbance please read the following instructions:
For your safety:
1 2 3 4 5
1 Safe operation of this machine is possible only
when the operating instructions and the safety
precautions are read completely and the
instructions contained therein are strictly observed.
2The machine must not be used in a wet environment.
3Always inspect cable and plug before using machine.
Only have damage repaired by a qualified professional.
Put the plug into the mains socket only when the
machine is switched off.
4+5 Always wears protective goggles, protective gloves
and heavy-duty shoes when working.
lDo not carry the machine by the cable.
lAlways remove the plug from the power supply
socket before carrying out any work on the machine,
when interrupting work and when not using the
machine.
lAlways place the cable to the rear away from the
machine.
lApply the machine to the sheet metal only when
switched on.
lAlways provide for secure footing when working.
lFirmly clamp the work piece if it does not remain
stationary from its own weight.
lThe knife should not rub on the jaws: Possible danger
of cutting tool breakage.
lDo not exceed the maximum allowable material
thickness especially when cutting over double folded
joints or welded seams.
FFor further notes on safety refer to enclosed sheet
DRÄCO Radius Seam Metal Shear
type
3514-7R
3514-7R
max. cutting capacity
Art.no.
61080
spare parts
steel
400 N/mm²
mm/ga.
2,0 / 14
knife
371401
stainless steel
600 N/mm²
mm/ga.
1,5 / 16
set of jaws
BG37222
stainless steel
800 N/mm²
mm/ga.
1,3 / 18
knife-pin set
BG35055
aluminium
250 N/mm²
mm/ga.
3,0 / 10
duct- & Pittsburgh Seam
400 N/mm²
mm/ga.
4 x 0,75 / 21
optional accessories
tightest radius
mm/ “
45 / 1¾
metal-box
18000
working speed ±
m/min
5-7
strokes
min -1
2400
motor capacity
Watts
500
weight
kg
2
starting hole
Ø mm
14
0óI
spiral ducting starting hole 12-14 mm Ø
accurate cutting along a marked line
20.11.2015 Specifications are subject to change for improvement without prior notice.
Operating instructions
1. Intended use. This Power Tool is intended for
industrial applications, for cutting sheet metal
(maximum capacity is indicated in the
Specifications), for use with cutting jaws and
cutting blades which are indicated in these
operating instructions or recommended by
DRÄCO.
2. Do NOT cut sheet metal along welding points. Do
NOT cut multi layer sheets, which exceed the
maximum cutting capacity.
3. Switching ON/OFF the power tool. First check
cable and plug for damage. Slide the switch pad
(5) BACKWARD for switching ON the power
tool. Slide the switch pad (5) FORWARD for
switching OFF the power tool.
4. For inside cutting, the shortest curve possible has
a radius of 45 mm (±1¾”). If cutting a radius with
the right hand, cut from right to left. The outside
radius is unlimited.
5. For cutting out curved or circular inside patterns,
a 14 mm (± 1/2 “) hole, or a punched slot should
be made to insert the centre cutter.
6. If after cutting, a small strip remains this can
easily be trimmed off to the exact measurement,
without leaving a burr or any distortion of the
material. Just one side of the power tools can be
used for cutting also (e.g. along a marked line).
Lift the power tools out of the shavings while the
motor is running. Cut off longer shavings.
7. Both knife and jaws can be sharpened. After
being sharpened or replaced, the knife at it’s
lowest point should protrude the jaws by
approximately 3 mm. The knife should have
approximately 0,05 mm (0,005”) play on each
side of the jaws, centring the cutter with spacing
shims supplied.
8. Every 200 operating ours have the cutting blade
and cutting jaws sharpened at a specialist
workshop.
9. Ensure that the material to be cut is free of oil
and grease.
Care and Maintenance
Warranty
Before working on machine disconnect from power
supply by removing plug from socket.
Always keep the machine and the ventilation slots
clean.
Oil the knife pin and knife at regular intervals.
If the machine should happen to fail despite the care
taken in manufacture and testing, repair should be
carried out by an authorised customer services agent
for DRÄCO power tools
DRÄCO tools carry a guarantee of 12 months from
date of delivery.
Damage attributable to normal wear and tear,
overload or improper handling will be excluded from
the guarantee. (e.g. blades/knifes and jaws)
In case of complaint please send the machine,
undismantled, to your dealer or the DRÄCO Service
Center for electric power tools.
Environmental protection
CE-Declaration of conformity
Recycling raw materials instead of waste
disposal
Machine, accessories and packaging should be sorted
for environment-friendly recycling.
These instructions are printed on recycling paper
manufactured without chlorine
We declare under our sole responsibility that this product is
in conformity with the following standards.
EC 98/37, EC 93/ 68 EWG, EC 04/108 EC, or
standardisation documents DIN EN ISO 12100-1,
DIN EN ISO 12100-2, EN 50 144, EN 55 014
09 Susanne Draenert
Operating Instructions for the Radius-Seam Metal Shear 3514-7R
To avoid any disturbance please read the following instructions:
For your safety:
1 2 3 4 5
1 Safe operation of this machine is possible only
when the operating instructions and the safety
precautions are read completely and the
instructions contained therein are strictly observed.
2The machine must not be used in a wet environment.
3Always inspect cable and plug before using machine.
Only have damage repaired by a qualified professional.
Put the plug into the mains socket only when the
machine is switched off.
4+5 Always wears protective goggles, protective gloves
and heavy-duty shoes when working.
lDo not carry the machine by the cable.
lAlways remove the plug from the power supply
socket before carrying out any work on the machine,
when interrupting work and when not using the
machine.
lAlways place the cable to the rear away from the
machine.
lApply the machine to the sheet metal only when
switched on.
lAlways provide for secure footing when working.
lFirmly clamp the work piece if it does not remain
stationary from its own weight.
lThe knife should not rub on the jaws: Possible danger
of cutting tool breakage.
lDo not exceed the maximum allowable material
thickness especially when cutting over double folded
joints or welded seams.
FFor further notes on safety refer to enclosed sheet
DRÄCO Radius Seam Metal Shear
type
3514-7R
3514-7R
max. cutting capacity
Art.no.
61080
spare parts
steel
400 N/mm²
mm/ga.
2,0 / 14
knife
371401
stainless steel
600 N/mm²
mm/ga.
1,5 / 16
set of jaws
BG37222
stainless steel
800 N/mm²
mm/ga.
1,3 / 18
knife-pin set
BG35055
aluminium
250 N/mm²
mm/ga.
3,0 / 10
duct- & Pittsburgh Seam
400 N/mm²
mm/ga.
4 x 0,75 / 21
optional accessories
tightest radius
mm/ “
45 / 1¾
metal-box
18000
working speed ±
m/min
5-7
strokes
min -1
2400
motor capacity
Watts
500
weight
kg
2
starting hole
Ø mm
14
0óI
spiral ducting starting hole 12-14 mm Ø
accurate cutting along a marked line
20.11.2015 Specifications are subject to change for improvement without prior notice.
Operating instructions
1. Intended use. This Power Tool is intended for
industrial applications, for cutting sheet metal
(maximum capacity is indicated in the
Specifications), for use with cutting jaws and
cutting blades which are indicated in these
operating instructions or recommended by
DRÄCO.
2. Do NOT cut sheet metal along welding points. Do
NOT cut multi layer sheets, which exceed the
maximum cutting capacity.
3. Switching ON/OFF the power tool. First check
cable and plug for damage. Slide the switch pad
(5) BACKWARD for switching ON the power
tool. Slide the switch pad (5) FORWARD for
switching OFF the power tool.
4. For inside cutting, the shortest curve possible has
a radius of 45 mm (±1¾”). If cutting a radius with
the right hand, cut from right to left. The outside
radius is unlimited.
5. For cutting out curved or circular inside patterns,
a 14 mm (± 1/2 “) hole, or a punched slot should
be made to insert the centre cutter.
6. If after cutting, a small strip remains this can
easily be trimmed off to the exact measurement,
without leaving a burr or any distortion of the
material. Just one side of the power tools can be
used for cutting also (e.g. along a marked line).
Lift the power tools out of the shavings while the
motor is running. Cut off longer shavings.
7. Both knife and jaws can be sharpened. After
being sharpened or replaced, the knife at it’s
lowest point should protrude the jaws by
approximately 3 mm. The knife should have
approximately 0,05 mm (0,005”) play on each
side of the jaws, centring the cutter with spacing
shims supplied.
8. Every 200 operating ours have the cutting blade
and cutting jaws sharpened at a specialist
workshop.
9. Ensure that the material to be cut is free of oil
and grease.
Care and Maintenance
Warranty
Before working on machine disconnect from power
supply by removing plug from socket.
Always keep the machine and the ventilation slots
clean.
Oil the knife pin and knife at regular intervals.
If the machine should happen to fail despite the care
taken in manufacture and testing, repair should be
carried out by an authorised customer services agent
for DRÄCO power tools
DRÄCO tools carry a guarantee of 12 months from
date of delivery.
Damage attributable to normal wear and tear,
overload or improper handling will be excluded from
the guarantee. (e.g. blades/knifes and jaws)
In case of complaint please send the machine,
undismantled, to your dealer or the DRÄCO Service
Center for electric power tools.
Environmental protection
CE-Declaration of conformity
Recycling raw materials instead of waste
disposal
Machine, accessories and packaging should be sorted
for environment-friendly recycling.
These instructions are printed on recycling paper
manufactured without chlorine
We declare under our sole responsibility that this product is
in conformity with the following standards.
EC 98/37, EC 93/ 68 EWG, EC 04/108 EC, or
standardisation documents DIN EN ISO 12100-1,
DIN EN ISO 12100-2, EN 50 144, EN 55 014
09 Susanne Draenert
Operating Instructions for the Radius-Seam Metal Shear 3514-7R
To avoid any disturbance please read the following instructions:
For your safety:
1 2 3 4 5
1 Safe operation of this machine is possible only
when the operating instructions and the safety
precautions are read completely and the
instructions contained therein are strictly observed.
2The machine must not be used in a wet environment.
3Always inspect cable and plug before using machine.
Only have damage repaired by a qualified professional.
Put the plug into the mains socket only when the
machine is switched off.
4+5 Always wears protective goggles, protective gloves
and heavy-duty shoes when working.
lDo not carry the machine by the cable.
lAlways remove the plug from the power supply
socket before carrying out any work on the machine,
when interrupting work and when not using the
machine.
lAlways place the cable to the rear away from the
machine.
lApply the machine to the sheet metal only when
switched on.
lAlways provide for secure footing when working.
lFirmly clamp the work piece if it does not remain
stationary from its own weight.
lThe knife should not rub on the jaws: Possible danger
of cutting tool breakage.
lDo not exceed the maximum allowable material
thickness especially when cutting over double folded
joints or welded seams.
FFor further notes on safety refer to enclosed sheet
DRÄCO Radius Seam Metal Shear
type
3514-7R
3514-7R
max. cutting capacity
Art.no.
61080
spare parts
steel
400 N/mm²
mm/ga.
2,0 / 14
knife
371401
stainless steel
600 N/mm²
mm/ga.
1,5 / 16
set of jaws
BG37222
stainless steel
800 N/mm²
mm/ga.
1,3 / 18
knife-pin set
BG35055
aluminium
250 N/mm²
mm/ga.
3,0 / 10
duct- & Pittsburgh Seam
400 N/mm²
mm/ga.
4 x 0,75 / 21
optional accessories
tightest radius
mm/ “
45 / 1¾
metal-box
18000
working speed ±
m/min
5-7
strokes
min -1
2400
motor capacity
Watts
500
weight
kg
2
starting hole
Ø mm
14
0óI
spiral ducting starting hole 12-14 mm Ø
accurate cutting along a marked line
20.11.2015 Specifications are subject to change for improvement without prior notice.
Operating instructions
1. Intended use. This Power Tool is intended for
industrial applications, for cutting sheet metal
(maximum capacity is indicated in the
Specifications), for use with cutting jaws and
cutting blades which are indicated in these
operating instructions or recommended by
DRÄCO.
2. Do NOT cut sheet metal along welding points. Do
NOT cut multi layer sheets, which exceed the
maximum cutting capacity.
3. Switching ON/OFF the power tool. First check
cable and plug for damage. Slide the switch pad
(5) BACKWARD for switching ON the power
tool. Slide the switch pad (5) FORWARD for
switching OFF the power tool.
4. For inside cutting, the shortest curve possible has
a radius of 45 mm (±1¾”). If cutting a radius with
the right hand, cut from right to left. The outside
radius is unlimited.
5. For cutting out curved or circular inside patterns,
a 14 mm (± 1/2 “) hole, or a punched slot should
be made to insert the centre cutter.
6. If after cutting, a small strip remains this can
easily be trimmed off to the exact measurement,
without leaving a burr or any distortion of the
material. Just one side of the power tools can be
used for cutting also (e.g. along a marked line).
Lift the power tools out of the shavings while the
motor is running. Cut off longer shavings.
7. Both knife and jaws can be sharpened. After
being sharpened or replaced, the knife at it’s
lowest point should protrude the jaws by
approximately 3 mm. The knife should have
approximately 0,05 mm (0,005”) play on each
side of the jaws, centring the cutter with spacing
shims supplied.
8. Every 200 operating ours have the cutting blade
and cutting jaws sharpened at a specialist
workshop.
9. Ensure that the material to be cut is free of oil
and grease.
Care and Maintenance
Warranty
Before working on machine disconnect from power
supply by removing plug from socket.
Always keep the machine and the ventilation slots
clean.
Oil the knife pin and knife at regular intervals.
If the machine should happen to fail despite the care
taken in manufacture and testing, repair should be
carried out by an authorised customer services agent
for DRÄCO power tools
DRÄCO tools carry a guarantee of 12 months from
date of delivery.
Damage attributable to normal wear and tear,
overload or improper handling will be excluded from
the guarantee. (e.g. blades/knifes and jaws)
In case of complaint please send the machine,
undismantled, to your dealer or the DRÄCO Service
Center for electric power tools.
Environmental protection
CE-Declaration of conformity
Recycling raw materials instead of waste
disposal
Machine, accessories and packaging should be sorted
for environment-friendly recycling.
These instructions are printed on recycling paper
manufactured without chlorine
We declare under our sole responsibility that this product is
in conformity with the following standards.
EC 98/37, EC 93/ 68 EWG, EC 04/108 EC, or
standardisation documents DIN EN ISO 12100-1,
DIN EN ISO 12100-2, EN 50 144, EN 55 014
09 Susanne Draenert
Operating Instructions for the Radius-Seam Metal Shear 3514-7R
To avoid any disturbance please read the following instructions:
For your safety:
1 2 3 4 5
1 Safe operation of this machine is possible only
when the operating instructions and the safety
precautions are read completely and the
instructions contained therein are strictly observed.
2The machine must not be used in a wet environment.
3Always inspect cable and plug before using machine.
Only have damage repaired by a qualified professional.
Put the plug into the mains socket only when the
machine is switched off.
4+5 Always wears protective goggles, protective gloves
and heavy-duty shoes when working.
lDo not carry the machine by the cable.
lAlways remove the plug from the power supply
socket before carrying out any work on the machine,
when interrupting work and when not using the
machine.
lAlways place the cable to the rear away from the
machine.
lApply the machine to the sheet metal only when
switched on.
lAlways provide for secure footing when working.
lFirmly clamp the work piece if it does not remain
stationary from its own weight.
lThe knife should not rub on the jaws: Possible danger
of cutting tool breakage.
lDo not exceed the maximum allowable material
thickness especially when cutting over double folded
joints or welded seams.
FFor further notes on safety refer to enclosed sheet
DRÄCO Radius Seam Metal Shear
type
3514-7R
3514-7R
max. cutting capacity
Art.no.
61080
spare parts
steel
400 N/mm²
mm/ga.
2,0 / 14
knife
371401
stainless steel
600 N/mm²
mm/ga.
1,5 / 16
set of jaws
BG37222
stainless steel
800 N/mm²
mm/ga.
1,3 / 18
knife-pin set
BG35055
aluminium
250 N/mm²
mm/ga.
3,0 / 10
duct- & Pittsburgh Seam
400 N/mm²
mm/ga.
4 x 0,75 / 21
optional accessories
tightest radius
mm/ “
45 / 1¾
metal-box
18000
working speed ±
m/min
5-7
strokes
min -1
2400
motor capacity
Watts
500
weight
kg
2
starting hole
Ø mm
14
0óI
spiral ducting starting hole 12-14 mm Ø
accurate cutting along a marked line
20.11.2015 Specifications are subject to change for improvement without prior notice.
Operating instructions
1. Intended use. This Power Tool is intended for
industrial applications, for cutting sheet metal
(maximum capacity is indicated in the
Specifications), for use with cutting jaws and
cutting blades which are indicated in these
operating instructions or recommended by
DRÄCO.
2. Do NOT cut sheet metal along welding points. Do
NOT cut multi layer sheets, which exceed the
maximum cutting capacity.
3. Switching ON/OFF the power tool. First check
cable and plug for damage. Slide the switch pad
(5) BACKWARD for switching ON the power
tool. Slide the switch pad (5) FORWARD for
switching OFF the power tool.
4. For inside cutting, the shortest curve possible has
a radius of 45 mm (±1¾”). If cutting a radius with
the right hand, cut from right to left. The outside
radius is unlimited.
5. For cutting out curved or circular inside patterns,
a 14 mm (± 1/2 “) hole, or a punched slot should
be made to insert the centre cutter.
6. If after cutting, a small strip remains this can
easily be trimmed off to the exact measurement,
without leaving a burr or any distortion of the
material. Just one side of the power tools can be
used for cutting also (e.g. along a marked line).
Lift the power tools out of the shavings while the
motor is running. Cut off longer shavings.
7. Both knife and jaws can be sharpened. After
being sharpened or replaced, the knife at it’s
lowest point should protrude the jaws by
approximately 3 mm. The knife should have
approximately 0,05 mm (0,005”) play on each
side of the jaws, centring the cutter with spacing
shims supplied.
8. Every 200 operating ours have the cutting blade
and cutting jaws sharpened at a specialist
workshop.
9. Ensure that the material to be cut is free of oil
and grease.
Care and Maintenance
Warranty
Before working on machine disconnect from power
supply by removing plug from socket.
Always keep the machine and the ventilation slots
clean.
Oil the knife pin and knife at regular intervals.
If the machine should happen to fail despite the care
taken in manufacture and testing, repair should be
carried out by an authorised customer services agent
for DRÄCO power tools
DRÄCO tools carry a guarantee of 12 months from
date of delivery.
Damage attributable to normal wear and tear,
overload or improper handling will be excluded from
the guarantee. (e.g. blades/knifes and jaws)
In case of complaint please send the machine,
undismantled, to your dealer or the DRÄCO Service
Center for electric power tools.
Environmental protection
CE-Declaration of conformity
Recycling raw materials instead of waste
disposal
Machine, accessories and packaging should be sorted
for environment-friendly recycling.
These instructions are printed on recycling paper
manufactured without chlorine
We declare under our sole responsibility that this product is
in conformity with the following standards.
EC 98/37, EC 93/ 68 EWG, EC 04/108 EC, or
standardisation documents DIN EN ISO 12100-1,
DIN EN ISO 12100-2, EN 50 144, EN 55 014
09 Susanne Draenert
Operating Instructions for the Radius-Seam Metal Shear 3514-7R
To avoid any disturbance please read the following instructions:
For your safety:
1 2 3 4 5
1 Safe operation of this machine is possible only
when the operating instructions and the safety
precautions are read completely and the
instructions contained therein are strictly observed.
2The machine must not be used in a wet environment.
3Always inspect cable and plug before using machine.
Only have damage repaired by a qualified professional.
Put the plug into the mains socket only when the
machine is switched off.
4+5 Always wears protective goggles, protective gloves
and heavy-duty shoes when working.
lDo not carry the machine by the cable.
lAlways remove the plug from the power supply
socket before carrying out any work on the machine,
when interrupting work and when not using the
machine.
lAlways place the cable to the rear away from the
machine.
lApply the machine to the sheet metal only when
switched on.
lAlways provide for secure footing when working.
lFirmly clamp the work piece if it does not remain
stationary from its own weight.
lThe knife should not rub on the jaws: Possible danger
of cutting tool breakage.
lDo not exceed the maximum allowable material
thickness especially when cutting over double folded
joints or welded seams.
FFor further notes on safety refer to enclosed sheet
DRÄCO Radius Seam Metal Shear
type
3514-7R
3514-7R
max. cutting capacity
Art.no.
61080
spare parts
steel
400 N/mm²
mm/ga.
2,0 / 14
knife
371401
stainless steel
600 N/mm²
mm/ga.
1,5 / 16
set of jaws
BG37222
stainless steel
800 N/mm²
mm/ga.
1,3 / 18
knife-pin set
BG35055
aluminium
250 N/mm²
mm/ga.
3,0 / 10
duct- & Pittsburgh Seam
400 N/mm²
mm/ga.
4 x 0,75 / 21
optional accessories
tightest radius
mm/ “
45 / 1¾
metal-box
18000
working speed ±
m/min
5-7
strokes
min -1
2400
motor capacity
Watts
500
weight
kg
2
starting hole
Ø mm
14
0óI
spiral ducting starting hole 12-14 mm Ø
accurate cutting along a marked line
20.11.2015 Specifications are subject to change for improvement without prior notice.
Operating instructions
1. Intended use. This Power Tool is intended for
industrial applications, for cutting sheet metal
(maximum capacity is indicated in the
Specifications), for use with cutting jaws and
cutting blades which are indicated in these
operating instructions or recommended by
DRÄCO.
2. Do NOT cut sheet metal along welding points. Do
NOT cut multi layer sheets, which exceed the
maximum cutting capacity.
3. Switching ON/OFF the power tool. First check
cable and plug for damage. Slide the switch pad
(5) BACKWARD for switching ON the power
tool. Slide the switch pad (5) FORWARD for
switching OFF the power tool.
4. For inside cutting, the shortest curve possible has
a radius of 45 mm (±1¾”). If cutting a radius with
the right hand, cut from right to left. The outside
radius is unlimited.
5. For cutting out curved or circular inside patterns,
a 14 mm (± 1/2 “) hole, or a punched slot should
be made to insert the centre cutter.
6. If after cutting, a small strip remains this can
easily be trimmed off to the exact measurement,
without leaving a burr or any distortion of the
material. Just one side of the power tools can be
used for cutting also (e.g. along a marked line).
Lift the power tools out of the shavings while the
motor is running. Cut off longer shavings.
7. Both knife and jaws can be sharpened. After
being sharpened or replaced, the knife at it’s
lowest point should protrude the jaws by
approximately 3 mm. The knife should have
approximately 0,05 mm (0,005”) play on each
side of the jaws, centring the cutter with spacing
shims supplied.
8. Every 200 operating ours have the cutting blade
and cutting jaws sharpened at a specialist
workshop.
9. Ensure that the material to be cut is free of oil
and grease.
Care and Maintenance
Warranty
Before working on machine disconnect from power
supply by removing plug from socket.
Always keep the machine and the ventilation slots
clean.
Oil the knife pin and knife at regular intervals.
If the machine should happen to fail despite the care
taken in manufacture and testing, repair should be
carried out by an authorised customer services agent
for DRÄCO power tools
DRÄCO tools carry a guarantee of 12 months from
date of delivery.
Damage attributable to normal wear and tear,
overload or improper handling will be excluded from
the guarantee. (e.g. blades/knifes and jaws)
In case of complaint please send the machine,
undismantled, to your dealer or the DRÄCO Service
Center for electric power tools.
Environmental protection
CE-Declaration of conformity
Recycling raw materials instead of waste
disposal
Machine, accessories and packaging should be sorted
for environment-friendly recycling.
These instructions are printed on recycling paper
manufactured without chlorine
We declare under our sole responsibility that this product is
in conformity with the following standards.
EC 98/37, EC 93/ 68 EWG, EC 04/108 EC, or
standardisation documents DIN EN ISO 12100-1,
DIN EN ISO 12100-2, EN 50 144, EN 55 014
09 Susanne Draenert
Operating Instructions for the Radius-Seam Metal Shear 3514-7R
To avoid any disturbance please read the following instructions:
For your safety:
1 2 3 4 5
1 Safe operation of this machine is possible only
when the operating instructions and the safety
precautions are read completely and the
instructions contained therein are strictly observed.
2The machine must not be used in a wet environment.
3Always inspect cable and plug before using machine.
Only have damage repaired by a qualified professional.
Put the plug into the mains socket only when the
machine is switched off.
4+5 Always wears protective goggles, protective gloves
and heavy-duty shoes when working.
lDo not carry the machine by the cable.
lAlways remove the plug from the power supply
socket before carrying out any work on the machine,
when interrupting work and when not using the
machine.
lAlways place the cable to the rear away from the
machine.
lApply the machine to the sheet metal only when
switched on.
lAlways provide for secure footing when working.
lFirmly clamp the work piece if it does not remain
stationary from its own weight.
lThe knife should not rub on the jaws: Possible danger
of cutting tool breakage.
lDo not exceed the maximum allowable material
thickness especially when cutting over double folded
joints or welded seams.
FFor further notes on safety refer to enclosed sheet
DRÄCO Radius Seam Metal Shear
type
3514-7R
3514-7R
max. cutting capacity
Art.no.
61080
spare parts
steel
400 N/mm²
mm/ga.
2,0 / 14
knife
371401
stainless steel
600 N/mm²
mm/ga.
1,5 / 16
set of jaws
BG37222
stainless steel
800 N/mm²
mm/ga.
1,3 / 18
knife-pin set
BG35055
aluminium
250 N/mm²
mm/ga.
3,0 / 10
duct- & Pittsburgh Seam
400 N/mm²
mm/ga.
4 x 0,75 / 21
optional accessories
tightest radius
mm/ “
45 / 1¾
metal-box
18000
working speed ±
m/min
5-7
strokes
min -1
2400
motor capacity
Watts
500
weight
kg
2
starting hole
Ø mm
14
0óI
spiral ducting starting hole 12-14 mm Ø
accurate cutting along a marked line
20.11.2015 Specifications are subject to change for improvement without prior notice.
Replacing/Adjusting the Knife
Before working on machine disconnect from power
supply by removing plug from socket.
Wear protective glasses!
Replacing the Knife
Clamp the machine in a vice on the clamping surfaces
SV between aluminium protective jaws.
Unscrew the screws 70 and remove the spring plate 71.
Remove the spring 72. Remove the Cotter Pin 76 and the Washer
77. Push back the knife pin 78.
Do NOT interchange the Spacing Shims 79: the wrong spacing
could ruin the jaws and knife.
Insert a new knife with the old spacing Shims 79. Insert the knife pin
8. Mount the washer 77 and the Cotter Pin 76.
Insert the spring 72. Reassemble spring plate 71.
Replacing the Jaws
Loosen the screws 80 and remove the jaws 82. Press out the
positioning pins 81. Mount new jaws and positioning pins. Tighten
the screws 80.
Adjusting the knife Clearance
For clearance between knife and jaws that is too large, loosen the
fillister head screw 67. Adjust the clearance with the setscrew 68.
Retighten the fillister head screw 67.
The knife must not rub on the jaws: Danger of breakage.
Note: If heavy burring is produced while cutting, repeat the
adjustment.
Sharpening the Knife/Jaws
The Knife and the Jaws must be sharpened and adjusted at the
same time. This work should be performed by an authorised
DRÄCO customer service location. Send in the complete machine
for this purpose.
Spare part List DRÄCO Radius Seam Metal Shear 3514-7R
Pos.
Description
Qty.
Order-No.
Pos.
Description
Qty.
Order-No.
Shear Head 3514-7R cpl. assembl.
1
37515
39
Washer
3
81059
Pos. 35, 39, 44-82
44
Ball Bearing
1
13039
45
Gear
1
13540
46
Pinion
1
13041
Drive Shaft cpl. Pos. 54-62
1
BG31558
47
Sleeve
1
13042
Pinion with Gear cpl. Pos. 39, 44-47
1
BG31541
48
Needle Bearing
1
13043
Motor cpl. 230 V
1
32229
49
Securing Washer
3
81249
Motor cpl. 115 V
1
32129
50
Screw
3
81262
51
Gear Case Cover Pos. 48-53
1
BG13046
1
Motor Housing
1
32040
52
Securing Washer
2
81243
2
Housing Cap
1
32047
53
Hex Socket Screw
2
81031
3
Switch
1
32050
54
Circlip
1
10009
4
Guide Piece
1
32054
55
Key
1
10006
5
Switch Pad
1
32056
56
Gear
1
13051
6
Pressure Spring
1
32055
57
Cover for Needle Bearing Pos. 57+59
1
BG10450
7
Wire
2
32044
58+62
Sleeve
1
10005
8
Carbon Brush
2
32042
59+63
Needle Bearing
1
10300
9
Carbon Brush Holder
2
32041
60
Roller Bearing
1
35285
10
Condensator
1
32045
61
Eccentric Shaft assembled Pos. 54+55,60-62
1
BG35556
11
Cable with Plug
1
32046
64
Head Casting Pos. 63-65+69
1
BG37547
12
Connection Cable
1
32522
65
Knife Pin Bushing
2
35542
13
Screw
2
32048
66
Spacing Block Pos. 66-68
1
BG37059
14
Screw
2
32053
67
Screw
1
81176
15
Cable Collar
1
32052
68
Tap Screw
1
81120
16
Field 230 V
1
32039
69
Tap Screw
2
81239
16
Field 115 V
1
32139
70
Screw
4
81285
17
Air Deflector Ring
1
32038
71
Spring Cover Plate
1
12300
18
Rubber Sleeve
1
32036
71
Spring Cover Plate Pos. 70-72
1
BG12300
19
Ball Bearing
1
32030
72
Spring
1
12200
20
Washer
1
32037
73-74
Knife Adjust Screw with Locking
1
35566
21
Armature 230 V
1
32033
73-75
Knife 3514-7R
1
37140
21
Armature 115 V
1
32133
78-79
Knife-pin set BG12400+BG35145
1
BG35055
23
Bearing Cover
1
32032
76
Safety Cotter Pin
2
35054
24
Ball Bearing
1
10038
77
Washer
2
81072
25
Securing Ring
1
32034
78
Knife Pin Pos. 76-78
1
BG35145
27
Bearing End Plate
1
32014
79
Spacing Shims Set
1
BG12400
28
Screw
4
32010
80
Screw
4
81440
29
Pin
1
81132
81
Pin
4
81248
30
Screw
2
32012
82
Set of Jaws 3514-7R
1
37222
31
Rating Plate
1
32057
82
Set of Jaws 3514-7R Pos. 80-82
1
BG37222
Max Draenert GmbH & Co.KG Electric - Cordless - Pneumatic Tools - Machines Germany
Werk I:
Administration
D-73777 Deizisau
P.O.Box
1120
Tel.
+49-7153-8217-0
Production Shears
K-Series
D-73779 Deizisau
Gutenbergstreet
15-17
Fax
+49-7153-8217-66
Internet
http://www.dracotools.com
E-mail:
20.11.2015 Specifications are subject to change for improvement without prior notice.
Replacing/Adjusting the Knife
Before working on machine disconnect from power
supply by removing plug from socket.
Wear protective glasses!
Replacing the Knife
Clamp the machine in a vice on the clamping surfaces
SV between aluminium protective jaws.
Unscrew the screws 70 and remove the spring plate 71.
Remove the spring 72. Remove the Cotter Pin 76 and the Washer
77. Push back the knife pin 78.
Do NOT interchange the Spacing Shims 79: the wrong spacing
could ruin the jaws and knife.
Insert a new knife with the old spacing Shims 79. Insert the knife pin
8. Mount the washer 77 and the Cotter Pin 76.
Insert the spring 72. Reassemble spring plate 71.
Replacing the Jaws
Loosen the screws 80 and remove the jaws 82. Press out the
positioning pins 81. Mount new jaws and positioning pins. Tighten
the screws 80.
Adjusting the knife Clearance
For clearance between knife and jaws that is too large, loosen the
fillister head screw 67. Adjust the clearance with the setscrew 68.
Retighten the fillister head screw 67.
The knife must not rub on the jaws: Danger of breakage.
Note: If heavy burring is produced while cutting, repeat the
adjustment.
Sharpening the Knife/Jaws
The Knife and the Jaws must be sharpened and adjusted at the
same time. This work should be performed by an authorised
DRÄCO customer service location. Send in the complete machine
for this purpose.
Spare part List DRÄCO Radius Seam Metal Shear 3514-7R
Pos.
Description
Qty.
Order-No.
Pos.
Description
Qty.
Order-No.
Shear Head 3514-7R cpl. assembl.
1
37515
39
Washer
3
81059
Pos. 35, 39, 44-82
44
Ball Bearing
1
13039
45
Gear
1
13540
46
Pinion
1
13041
Drive Shaft cpl. Pos. 54-62
1
BG31558
47
Sleeve
1
13042
Pinion with Gear cpl. Pos. 39, 44-47
1
BG31541
48
Needle Bearing
1
13043
Motor cpl. 230 V
1
32229
49
Securing Washer
3
81249
Motor cpl. 115 V
1
32129
50
Screw
3
81262
51
Gear Case Cover Pos. 48-53
1
BG13046
1
Motor Housing
1
32040
52
Securing Washer
2
81243
2
Housing Cap
1
32047
53
Hex Socket Screw
2
81031
3
Switch
1
32050
54
Circlip
1
10009
4
Guide Piece
1
32054
55
Key
1
10006
5
Switch Pad
1
32056
56
Gear
1
13051
6
Pressure Spring
1
32055
57
Cover for Needle Bearing Pos. 57+59
1
BG10450
7
Wire
2
32044
58+62
Sleeve
1
10005
8
Carbon Brush
2
32042
59+63
Needle Bearing
1
10300
9
Carbon Brush Holder
2
32041
60
Roller Bearing
1
35285
10
Condensator
1
32045
61
Eccentric Shaft assembled Pos. 54+55,60-62
1
BG35556
11
Cable with Plug
1
32046
64
Head Casting Pos. 63-65+69
1
BG37547
12
Connection Cable
1
32522
65
Knife Pin Bushing
2
35542
13
Screw
2
32048
66
Spacing Block Pos. 66-68
1
BG37059
14
Screw
2
32053
67
Screw
1
81176
15
Cable Collar
1
32052
68
Tap Screw
1
81120
16
Field 230 V
1
32039
69
Tap Screw
2
81239
16
Field 115 V
1
32139
70
Screw
4
81285
17
Air Deflector Ring
1
32038
71
Spring Cover Plate
1
12300
18
Rubber Sleeve
1
32036
71
Spring Cover Plate Pos. 70-72
1
BG12300
19
Ball Bearing
1
32030
72
Spring
1
12200
20
Washer
1
32037
73-74
Knife Adjust Screw with Locking
1
35566
21
Armature 230 V
1
32033
73-75
Knife 3514-7R
1
37140
21
Armature 115 V
1
32133
78-79
Knife-pin set BG12400+BG35145
1
BG35055
23
Bearing Cover
1
32032
76
Safety Cotter Pin
2
35054
24
Ball Bearing
1
10038
77
Washer
2
81072
25
Securing Ring
1
32034
78
Knife Pin Pos. 76-78
1
BG35145
27
Bearing End Plate
1
32014
79
Spacing Shims Set
1
BG12400
28
Screw
4
32010
80
Screw
4
81440
29
Pin
1
81132
81
Pin
4
81248
30
Screw
2
32012
82
Set of Jaws 3514-7R
1
37222
31
Rating Plate
1
32057
82
Set of Jaws 3514-7R Pos. 80-82
1
BG37222
Max Draenert GmbH & Co.KG Electric - Cordless - Pneumatic Tools - Machines Germany
Werk I:
Administration
D-73777 Deizisau
P.O.Box
1120
Tel.
+49-7153-8217-0
Production Shears
K-Series
D-73779 Deizisau
Gutenbergstreet
15-17
Fax
+49-7153-8217-66
Internet
http://www.dracotools.com
E-mail:
20.11.2015 Specifications are subject to change for improvement without prior notice.
Replacing/Adjusting the Knife
Before working on machine disconnect from power
supply by removing plug from socket.
Wear protective glasses!
Replacing the Knife
Clamp the machine in a vice on the clamping surfaces
SV between aluminium protective jaws.
Unscrew the screws 70 and remove the spring plate 71.
Remove the spring 72. Remove the Cotter Pin 76 and the Washer
77. Push back the knife pin 78.
Do NOT interchange the Spacing Shims 79: the wrong spacing
could ruin the jaws and knife.
Insert a new knife with the old spacing Shims 79. Insert the knife pin
8. Mount the washer 77 and the Cotter Pin 76.
Insert the spring 72. Reassemble spring plate 71.
Replacing the Jaws
Loosen the screws 80 and remove the jaws 82. Press out the
positioning pins 81. Mount new jaws and positioning pins. Tighten
the screws 80.
Adjusting the knife Clearance
For clearance between knife and jaws that is too large, loosen the
fillister head screw 67. Adjust the clearance with the setscrew 68.
Retighten the fillister head screw 67.
The knife must not rub on the jaws: Danger of breakage.
Note: If heavy burring is produced while cutting, repeat the
adjustment.
Sharpening the Knife/Jaws
The Knife and the Jaws must be sharpened and adjusted at the
same time. This work should be performed by an authorised
DRÄCO customer service location. Send in the complete machine
for this purpose.
Spare part List DRÄCO Radius Seam Metal Shear 3514-7R
Pos.
Description
Qty.
Order-No.
Pos.
Description
Qty.
Order-No.
Shear Head 3514-7R cpl. assembl.
1
37515
39
Washer
3
81059
Pos. 35, 39, 44-82
44
Ball Bearing
1
13039
45
Gear
1
13540
46
Pinion
1
13041
Drive Shaft cpl. Pos. 54-62
1
BG31558
47
Sleeve
1
13042
Pinion with Gear cpl. Pos. 39, 44-47
1
BG31541
48
Needle Bearing
1
13043
Motor cpl. 230 V
1
32229
49
Securing Washer
3
81249
Motor cpl. 115 V
1
32129
50
Screw
3
81262
51
Gear Case Cover Pos. 48-53
1
BG13046
1
Motor Housing
1
32040
52
Securing Washer
2
81243
2
Housing Cap
1
32047
53
Hex Socket Screw
2
81031
3
Switch
1
32050
54
Circlip
1
10009
4
Guide Piece
1
32054
55
Key
1
10006
5
Switch Pad
1
32056
56
Gear
1
13051
6
Pressure Spring
1
32055
57
Cover for Needle Bearing Pos. 57+59
1
BG10450
7
Wire
2
32044
58+62
Sleeve
1
10005
8
Carbon Brush
2
32042
59+63
Needle Bearing
1
10300
9
Carbon Brush Holder
2
32041
60
Roller Bearing
1
35285
10
Condensator
1
32045
61
Eccentric Shaft assembled Pos. 54+55,60-62
1
BG35556
11
Cable with Plug
1
32046
64
Head Casting Pos. 63-65+69
1
BG37547
12
Connection Cable
1
32522
65
Knife Pin Bushing
2
35542
13
Screw
2
32048
66
Spacing Block Pos. 66-68
1
BG37059
14
Screw
2
32053
67
Screw
1
81176
15
Cable Collar
1
32052
68
Tap Screw
1
81120
16
Field 230 V
1
32039
69
Tap Screw
2
81239
16
Field 115 V
1
32139
70
Screw
4
81285
17
Air Deflector Ring
1
32038
71
Spring Cover Plate
1
12300
18
Rubber Sleeve
1
32036
71
Spring Cover Plate Pos. 70-72
1
BG12300
19
Ball Bearing
1
32030
72
Spring
1
12200
20
Washer
1
32037
73-74
Knife Adjust Screw with Locking
1
35566
21
Armature 230 V
1
32033
73-75
Knife 3514-7R
1
37140
21
Armature 115 V
1
32133
78-79
Knife-pin set BG12400+BG35145
1
BG35055
23
Bearing Cover
1
32032
76
Safety Cotter Pin
2
35054
24
Ball Bearing
1
10038
77
Washer
2
81072
25
Securing Ring
1
32034
78
Knife Pin Pos. 76-78
1
BG35145
27
Bearing End Plate
1
32014
79
Spacing Shims Set
1
BG12400
28
Screw
4
32010
80
Screw
4
81440
29
Pin
1
81132
81
Pin
4
81248
30
Screw
2
32012
82
Set of Jaws 3514-7R
1
37222
31
Rating Plate
1
32057
82
Set of Jaws 3514-7R Pos. 80-82
1
BG37222
Max Draenert GmbH & Co.KG Electric - Cordless - Pneumatic Tools - Machines Germany
Werk I:
Administration
D-73777 Deizisau
P.O.Box
1120
Tel.
+49-7153-8217-0
Production Shears
K-Series
D-73779 Deizisau
Gutenbergstreet
15-17
Fax
+49-7153-8217-66
Internet
http://www.dracotools.com
E-mail:
20.11.2015 Specifications are subject to change for improvement without prior notice.
Replacing/Adjusting the Knife
Before working on machine disconnect from power
supply by removing plug from socket.
Wear protective glasses!
Replacing the Knife
Clamp the machine in a vice on the clamping surfaces
SV between aluminium protective jaws.
Unscrew the screws 70 and remove the spring plate 71.
Remove the spring 72. Remove the Cotter Pin 76 and the Washer
77. Push back the knife pin 78.
Do NOT interchange the Spacing Shims 79: the wrong spacing
could ruin the jaws and knife.
Insert a new knife with the old spacing Shims 79. Insert the knife pin
8. Mount the washer 77 and the Cotter Pin 76.
Insert the spring 72. Reassemble spring plate 71.
Replacing the Jaws
Loosen the screws 80 and remove the jaws 82. Press out the
positioning pins 81. Mount new jaws and positioning pins. Tighten
the screws 80.
Adjusting the knife Clearance
For clearance between knife and jaws that is too large, loosen the
fillister head screw 67. Adjust the clearance with the setscrew 68.
Retighten the fillister head screw 67.
The knife must not rub on the jaws: Danger of breakage.
Note: If heavy burring is produced while cutting, repeat the
adjustment.
Sharpening the Knife/Jaws
The Knife and the Jaws must be sharpened and adjusted at the
same time. This work should be performed by an authorised
DRÄCO customer service location. Send in the complete machine
for this purpose.
Spare part List DRÄCO Radius Seam Metal Shear 3514-7R
Pos.
Description
Qty.
Order-No.
Pos.
Description
Qty.
Order-No.
Shear Head 3514-7R cpl. assembl.
1
37515
39
Washer
3
81059
Pos. 35, 39, 44-82
44
Ball Bearing
1
13039
45
Gear
1
13540
46
Pinion
1
13041
Drive Shaft cpl. Pos. 54-62
1
BG31558
47
Sleeve
1
13042
Pinion with Gear cpl. Pos. 39, 44-47
1
BG31541
48
Needle Bearing
1
13043
Motor cpl. 230 V
1
32229
49
Securing Washer
3
81249
Motor cpl. 115 V
1
32129
50
Screw
3
81262
51
Gear Case Cover Pos. 48-53
1
BG13046
1
Motor Housing
1
32040
52
Securing Washer
2
81243
2
Housing Cap
1
32047
53
Hex Socket Screw
2
81031
3
Switch
1
32050
54
Circlip
1
10009
4
Guide Piece
1
32054
55
Key
1
10006
5
Switch Pad
1
32056
56
Gear
1
13051
6
Pressure Spring
1
32055
57
Cover for Needle Bearing Pos. 57+59
1
BG10450
7
Wire
2
32044
58+62
Sleeve
1
10005
8
Carbon Brush
2
32042
59+63
Needle Bearing
1
10300
9
Carbon Brush Holder
2
32041
60
Roller Bearing
1
35285
10
Condensator
1
32045
61
Eccentric Shaft assembled Pos. 54+55,60-62
1
BG35556
11
Cable with Plug
1
32046
64
Head Casting Pos. 63-65+69
1
BG37547
12
Connection Cable
1
32522
65
Knife Pin Bushing
2
35542
13
Screw
2
32048
66
Spacing Block Pos. 66-68
1
BG37059
14
Screw
2
32053
67
Screw
1
81176
15
Cable Collar
1
32052
68
Tap Screw
1
81120
16
Field 230 V
1
32039
69
Tap Screw
2
81239
16
Field 115 V
1
32139
70
Screw
4
81285
17
Air Deflector Ring
1
32038
71
Spring Cover Plate
1
12300
18
Rubber Sleeve
1
32036
71
Spring Cover Plate Pos. 70-72
1
BG12300
19
Ball Bearing
1
32030
72
Spring
1
12200
20
Washer
1
32037
73-74
Knife Adjust Screw with Locking
1
35566
21
Armature 230 V
1
32033
73-75
Knife 3514-7R
1
37140
21
Armature 115 V
1
32133
78-79
Knife-pin set BG12400+BG35145
1
BG35055
23
Bearing Cover
1
32032
76
Safety Cotter Pin
2
35054
24
Ball Bearing
1
10038
77
Washer
2
81072
25
Securing Ring
1
32034
78
Knife Pin Pos. 76-78
1
BG35145
27
Bearing End Plate
1
32014
79
Spacing Shims Set
1
BG12400
28
Screw
4
32010
80
Screw
4
81440
29
Pin
1
81132
81
Pin
4
81248
30
Screw
2
32012
82
Set of Jaws 3514-7R
1
37222
31
Rating Plate
1
32057
82
Set of Jaws 3514-7R Pos. 80-82
1
BG37222
Max Draenert GmbH & Co.KG Electric - Cordless - Pneumatic Tools - Machines Germany
Werk I:
Administration
D-73777 Deizisau
P.O.Box
1120
Tel.
+49-7153-8217-0
Production Shears
K-Series
D-73779 Deizisau
Gutenbergstreet
15-17
Fax
+49-7153-8217-66
Internet
http://www.dracotools.com
E-mail:
20.11.2015 Specifications are subject to change for improvement without prior notice.
Replacing/Adjusting the Knife
Before working on machine disconnect from power
supply by removing plug from socket.
Wear protective glasses!
Replacing the Knife
Clamp the machine in a vice on the clamping surfaces
SV between aluminium protective jaws.
Unscrew the screws 70 and remove the spring plate 71.
Remove the spring 72. Remove the Cotter Pin 76 and the Washer
77. Push back the knife pin 78.
Do NOT interchange the Spacing Shims 79: the wrong spacing
could ruin the jaws and knife.
Insert a new knife with the old spacing Shims 79. Insert the knife pin
8. Mount the washer 77 and the Cotter Pin 76.
Insert the spring 72. Reassemble spring plate 71.
Replacing the Jaws
Loosen the screws 80 and remove the jaws 82. Press out the
positioning pins 81. Mount new jaws and positioning pins. Tighten
the screws 80.
Adjusting the knife Clearance
For clearance between knife and jaws that is too large, loosen the
fillister head screw 67. Adjust the clearance with the setscrew 68.
Retighten the fillister head screw 67.
The knife must not rub on the jaws: Danger of breakage.
Note: If heavy burring is produced while cutting, repeat the
adjustment.
Sharpening the Knife/Jaws
The Knife and the Jaws must be sharpened and adjusted at the
same time. This work should be performed by an authorised
DRÄCO customer service location. Send in the complete machine
for this purpose.
Spare part List DRÄCO Radius Seam Metal Shear 3514-7R
Pos.
Description
Qty.
Order-No.
Pos.
Description
Qty.
Order-No.
Shear Head 3514-7R cpl. assembl.
1
37515
39
Washer
3
81059
Pos. 35, 39, 44-82
44
Ball Bearing
1
13039
45
Gear
1
13540
46
Pinion
1
13041
Drive Shaft cpl. Pos. 54-62
1
BG31558
47
Sleeve
1
13042
Pinion with Gear cpl. Pos. 39, 44-47
1
BG31541
48
Needle Bearing
1
13043
Motor cpl. 230 V
1
32229
49
Securing Washer
3
81249
Motor cpl. 115 V
1
32129
50
Screw
3
81262
51
Gear Case Cover Pos. 48-53
1
BG13046
1
Motor Housing
1
32040
52
Securing Washer
2
81243
2
Housing Cap
1
32047
53
Hex Socket Screw
2
81031
3
Switch
1
32050
54
Circlip
1
10009
4
Guide Piece
1
32054
55
Key
1
10006
5
Switch Pad
1
32056
56
Gear
1
13051
6
Pressure Spring
1
32055
57
Cover for Needle Bearing Pos. 57+59
1
BG10450
7
Wire
2
32044
58+62
Sleeve
1
10005
8
Carbon Brush
2
32042
59+63
Needle Bearing
1
10300
9
Carbon Brush Holder
2
32041
60
Roller Bearing
1
35285
10
Condensator
1
32045
61
Eccentric Shaft assembled Pos. 54+55,60-62
1
BG35556
11
Cable with Plug
1
32046
64
Head Casting Pos. 63-65+69
1
BG37547
12
Connection Cable
1
32522
65
Knife Pin Bushing
2
35542
13
Screw
2
32048
66
Spacing Block Pos. 66-68
1
BG37059
14
Screw
2
32053
67
Screw
1
81176
15
Cable Collar
1
32052
68
Tap Screw
1
81120
16
Field 230 V
1
32039
69
Tap Screw
2
81239
16
Field 115 V
1
32139
70
Screw
4
81285
17
Air Deflector Ring
1
32038
71
Spring Cover Plate
1
12300
18
Rubber Sleeve
1
32036
71
Spring Cover Plate Pos. 70-72
1
BG12300
19
Ball Bearing
1
32030
72
Spring
1
12200
20
Washer
1
32037
73-74
Knife Adjust Screw with Locking
1
35566
21
Armature 230 V
1
32033
73-75
Knife 3514-7R
1
37140
21
Armature 115 V
1
32133
78-79
Knife-pin set BG12400+BG35145
1
BG35055
23
Bearing Cover
1
32032
76
Safety Cotter Pin
2
35054
24
Ball Bearing
1
10038
77
Washer
2
81072
25
Securing Ring
1
32034
78
Knife Pin Pos. 76-78
1
BG35145
27
Bearing End Plate
1
32014
79
Spacing Shims Set
1
BG12400
28
Screw
4
32010
80
Screw
4
81440
29
Pin
1
81132
81
Pin
4
81248
30
Screw
2
32012
82
Set of Jaws 3514-7R
1
37222
31
Rating Plate
1
32057
82
Set of Jaws 3514-7R Pos. 80-82
1
BG37222
Max Draenert GmbH & Co.KG Electric - Cordless - Pneumatic Tools - Machines Germany
Werk I:
Administration
D-73777 Deizisau
P.O.Box
1120
Tel.
+49-7153-8217-0
Production Shears
K-Series
D-73779 Deizisau
Gutenbergstreet
15-17
Fax
+49-7153-8217-66
Internet
http://www.dracotools.com
E-mail:
20.11.2015 Specifications are subject to change for improvement without prior notice.
Replacing/Adjusting the Knife
Before working on machine disconnect from power
supply by removing plug from socket.
Wear protective glasses!
Replacing the Knife
Clamp the machine in a vice on the clamping surfaces
SV between aluminium protective jaws.
Unscrew the screws 70 and remove the spring plate 71.
Remove the spring 72. Remove the Cotter Pin 76 and the Washer
77. Push back the knife pin 78.
Do NOT interchange the Spacing Shims 79: the wrong spacing
could ruin the jaws and knife.
Insert a new knife with the old spacing Shims 79. Insert the knife pin
8. Mount the washer 77 and the Cotter Pin 76.
Insert the spring 72. Reassemble spring plate 71.
Replacing the Jaws
Loosen the screws 80 and remove the jaws 82. Press out the
positioning pins 81. Mount new jaws and positioning pins. Tighten
the screws 80.
Adjusting the knife Clearance
For clearance between knife and jaws that is too large, loosen the
fillister head screw 67. Adjust the clearance with the setscrew 68.
Retighten the fillister head screw 67.
The knife must not rub on the jaws: Danger of breakage.
Note: If heavy burring is produced while cutting, repeat the
adjustment.
Sharpening the Knife/Jaws
The Knife and the Jaws must be sharpened and adjusted at the
same time. This work should be performed by an authorised
DRÄCO customer service location. Send in the complete machine
for this purpose.
Spare part List DRÄCO Radius Seam Metal Shear 3514-7R
Pos.
Description
Qty.
Order-No.
Pos.
Description
Qty.
Order-No.
Shear Head 3514-7R cpl. assembl.
1
37515
39
Washer
3
81059
Pos. 35, 39, 44-82
44
Ball Bearing
1
13039
45
Gear
1
13540
46
Pinion
1
13041
Drive Shaft cpl. Pos. 54-62
1
BG31558
47
Sleeve
1
13042
Pinion with Gear cpl. Pos. 39, 44-47
1
BG31541
48
Needle Bearing
1
13043
Motor cpl. 230 V
1
32229
49
Securing Washer
3
81249
Motor cpl. 115 V
1
32129
50
Screw
3
81262
51
Gear Case Cover Pos. 48-53
1
BG13046
1
Motor Housing
1
32040
52
Securing Washer
2
81243
2
Housing Cap
1
32047
53
Hex Socket Screw
2
81031
3
Switch
1
32050
54
Circlip
1
10009
4
Guide Piece
1
32054
55
Key
1
10006
5
Switch Pad
1
32056
56
Gear
1
13051
6
Pressure Spring
1
32055
57
Cover for Needle Bearing Pos. 57+59
1
BG10450
7
Wire
2
32044
58+62
Sleeve
1
10005
8
Carbon Brush
2
32042
59+63
Needle Bearing
1
10300
9
Carbon Brush Holder
2
32041
60
Roller Bearing
1
35285
10
Condensator
1
32045
61
Eccentric Shaft assembled Pos. 54+55,60-62
1
BG35556
11
Cable with Plug
1
32046
64
Head Casting Pos. 63-65+69
1
BG37547
12
Connection Cable
1
32522
65
Knife Pin Bushing
2
35542
13
Screw
2
32048
66
Spacing Block Pos. 66-68
1
BG37059
14
Screw
2
32053
67
Screw
1
81176
15
Cable Collar
1
32052
68
Tap Screw
1
81120
16
Field 230 V
1
32039
69
Tap Screw
2
81239
16
Field 115 V
1
32139
70
Screw
4
81285
17
Air Deflector Ring
1
32038
71
Spring Cover Plate
1
12300
18
Rubber Sleeve
1
32036
71
Spring Cover Plate Pos. 70-72
1
BG12300
19
Ball Bearing
1
32030
72
Spring
1
12200
20
Washer
1
32037
73-74
Knife Adjust Screw with Locking
1
35566
21
Armature 230 V
1
32033
73-75
Knife 3514-7R
1
37140
21
Armature 115 V
1
32133
78-79
Knife-pin set BG12400+BG35145
1
BG35055
23
Bearing Cover
1
32032
76
Safety Cotter Pin
2
35054
24
Ball Bearing
1
10038
77
Washer
2
81072
25
Securing Ring
1
32034
78
Knife Pin Pos. 76-78
1
BG35145
27
Bearing End Plate
1
32014
79
Spacing Shims Set
1
BG12400
28
Screw
4
32010
80
Screw
4
81440
29
Pin
1
81132
81
Pin
4
81248
30
Screw
2
32012
82
Set of Jaws 3514-7R
1
37222
31
Rating Plate
1
32057
82
Set of Jaws 3514-7R Pos. 80-82
1
BG37222
Max Draenert GmbH & Co.KG Electric - Cordless - Pneumatic Tools - Machines Germany
Werk I:
Administration
D-73777 Deizisau
P.O.Box
1120
Tel.
+49-7153-8217-0
Production Shears
K-Series
D-73779 Deizisau
Gutenbergstreet
15-17
Fax
+49-7153-8217-66
Internet
http://www.dracotools.com
E-mail:
Other Draco Power Tools manuals
