Dreame F9 User manual

Robot Vacuum Mop F9
User Manual • Uživatelský manuál •
Užívateľský manuál • Használati utasítás •
Benutzerhandbuch

2
English
3 –24
Čeština
25 –46
Slovenčina
47 –68
Magyar
69 –91
Deutsch
92 –114

3
Dear customer,
Thank you for purchasing our product. Please read the following instructions carefully
before first use and keep this user manual for future reference. Pay particular attention to
the safety instructions. If you have any questions or comments about the device, please
contact the customer line.
✉www.alza.co.uk/kontakt
✆[phone]
Importer Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Prague 7, www.alza.cz

4
Safety Information
Only for navigation and positioning purposes, the camera of the vacuum-mop will collect
individuals in the surrounding within the range of the viewing angles when it is cleaning.
Please b assured that all your personal information will be protected by the data
encryption technology.
Usage Restriction
This product is for floor cleaning in a home environment only. Do not use it
outdoors, on non-floor surfaces, or in commercial or industrial setting.
Do not use the vacuum-mop in an area suspended above ground level without a
protective barrier.
Do not use the vacuum-mop at an ambient temperature above 40°C or below 0° or
on a floor with liquids or sticky substances.
Pick up any cables from the floor before using the vacuum-mop to prevent it from
dragging them while cleaning.
Remove fragile or small items from the floor to prevent the vacuum-mop from
bumping into and damaging them.
This product can be used by children aged from 8 years and above and persons
with physical, sensory, intellectual deficiencies or limited experience or knowledge,
under the supervision of a parent of guardian to ensure safe operation and to avoid
any risk of hazards. Cleaning and maintenance shall not be made by children
without supervision.
Children shall not paly with this product. Ensure children and pets are kept at a
safe distance from the vacuum mop while it is operating.
Keep the brush cleaning tool out of reach of children.
Do not place children, pets or any item on top of the vacuum-mop regardless of
whether it is stationary or moving.
Keep hair, fingers, and other body parts away from the suction opening of the
vacuum-mops.
Do not use the vacuum-mop to clean aby burning substances.
Do not vacuum up hard or sharp objects.
Make sure the vacuum is turned off and charging dock is unplugged before
cleaning or performing maintenance.
Do not wipe any part of this product using a wet cloth or any liquids.
Please use this product in accordance with the instructions in the User Manual.
Users are responsible for any loss or damage arising from improper use of this
product.

5
Batteries and Charging
Do not use any third party battery, charger, or charging dock. Use only with RCS0
supply unit.
Do not attempt to disassemble, repair, or modify the battery or charging dock on
your own.
Do not place the charging dock near a heat source.
Do not use a wet cloth or wet hands to wipe or clean dock’s charging contacts.
Do not improperly dispose of old batteries. Unneeded batteries should be discarded
at an appropriate recycling facility.
If the power cord becomes damaged or broken, stop using it immediately and
contact after-sales service.
Make sure the vacuum-mop is turned off when being transported and kept in its
original packaging if possible.
If the vacuum-mop will not be used for an extended period, fully charge it, then
turn it off and store in a cool, dry place. Recharge the vacuum-mop at least once
every 3 months to avoid over-discharging battery.
This product contains batteries that can only be replaced by qualified technicians
or after-sales service.
Product Overview
Accessories
Charging Dock
Cleaning Tool
Power Cord
Water Tank
Mop Pad
Side Brush
Note: The illustrations I this manual are for reference only, please refer to the actual
product for the actual appearance.

6
Vacuum-Mop
Vacuum-Mop
Power/Clean Button
Press and hold for 3 seconds
Press to start cleaning after the vakuum-mop is powered on
Status Indicator
White: Cleaning or cleanup is completed
Blinking white: Cleaning paused
Blinking blue: Connecting to network
Blinking orange: Error
Spot/Dock Button
Press and send vakuum-mop back to charging dock
Press and hold for 3 seconds to start Spot Clean Mode
Note: Press any button to pause while the vakuum-mop is
cleaning returning to dock, or in Spot Clean mode
Visual Navigation Sensor
Cover latch
Reset Button
Press and hold to restore factory settings
Wi-Fi Indicator
Blinking slowly: To be connected
Blinking quickly: Connecting
On: Wi-Fi connected
Cleaning Tool
Air Outlet/Speaker

7
Vacuum-Mop Sensors
Omnidirectional Wheel
Charging Contacts
Optical Sensor
Side Brush
Main Wheels
Main Brush
Brush Guard Clips
Cliff Sensors
Infrared Decelaration Sensor
Collision Buffer

8
Dust Bin
Mopping Module
Charging Dock
Bin Clip
Bin Cover
Filter
Water Tank
Water Tank Stopper
Mop Pad
Attaching Area
Signaling Area
Charging Contacts
Power Port

9
Preparation
Remove the protective film.
Install the slide brush.
Place the charging dock on the level ground against wall and connect to a
power outlet.

10
Note:
Make sure there is a distance of 0.5 meters or more on either side of the charging
dock, and more than 1.5 meters in front of it.
Tidy up any loose cord which could accidentally move or unplug the charging dock.
To ensure you can well connect to the vacuum-mop with your phone, make sure
the vacuum-mop and charging dock are in the range of Wi-Fi
Do not place the charging dock in an area with direct sunlight or where other
objects could block its signalling area, as this may hinder the vacuum-mop from
returning to the charging dock.
Place the robot onto the charging clock to recharge
Battery Level Indicator
White: Battery level is more than 15%
Orange: Battery level is less than 15%
Note:
Fully charge before first use.
Don’t install the mopping module while charging.
Connecting with Mi Home/Xiaomi Home App
This product works with Mi Home/Xiaomi Home app.
Scan the QR code to download and install the app.
You will be directed to the connection setup page if the app is installed already.
Or search “Mi Home/Xiaomi Home”in the app store to download and install it.
Open Mi Home / Xiaomi Home app, tap “+”on the upper right, and then follow prompts to
add your device.
Note: The version of the app might have been updated, please follow the instructions
based on the current app version.

11
Reset Wi-Fi
Simultaneously press and hold the buttons and until you hear a voice saying,
“Waiting for the network configuration”.
Once the Wi-Fi indicator is slowly blinking, the Wi-Fi has been successfully reset.
How to Use
Turn On/Off
Press and hold button to turn on the vacuum-mop. Once the power indicator turns solid
white, the vacuum-mop is in standby mode. To turn off the vacuum-mop, press and hold
the button while the vacuum-mop is stationary. Turning off the vacuum-mop will end
the current cleaning task.
Start Cleaning
Upon activation, the vacuum-mop will methodically clean each room in an S-shape patter,
then finish by cleaning along edges and wall to ensure a thorough job. When the vacuum-
mop is done cleaning, it will automatically return to the charging dock to recharge.
Note:
Please fully charged and start from the charging dock before cleaning. Don’t move
the robot and charging dock when the robot is working.
If the battery is too low, the robot will automatically return to the dock to charge. It
will resume unfinished cleaning tasks after charging to the appropriate power.

12
Cleaning Mode
Four cleaning modes are available in the app: Quiet, Standard, Strong and Turbo. The
default mode is Standard.
Pausing/Sleep Mode
Press any button to pause the vacuum-mop during cleaning.
The vacuum-mop will automatically enter sleep mode after 10 minutes of inactivity,
then the power and charging indicators will go off. To wake up the vacuum-mop,
press any button.
Note: When the vacuum-mop is paused, placing it onto the charging dock will end the
current cleaning task.
Spot Clean Mode
When the vacuum-mop is in standby mode or paused, press and hold the button for 3
seconds to start Spot Clean mode. In this mode, it will clean a square-shaped area of 1.5 x
1.5 meters directly around the vacuum-mop. When the spot cleaning is done, the vacuum-
mop will automatically return to its original location and shut off.
Note: Activating Spot Clean mode will end the current cleaning task of the vacuum-mop.
Do Not Disturb Mode
Do not Disturb mode prevents the vacuum-mop from automatically starting cleaning
tasks, and the power indicator remains off. You can enable Do Not Disturb or modify its
hours in the app.
Note:
Scheduled clean-ups will still be carried out during the DND period.
The vacuum-mop will continue cleaning after this period ends.
Scheduled Cleaning
You can schedule cleaning time in the app.
The vacuum-mop will automatically start cleaning at the designated time and then return
to the charging dock to recharge when the cleaning is done.
Advanced Function
The app can be used to set up advanced functions such as selected rom cleaning, zone
cleaning, forbidden area / virtual wall, etc.

13
Note:
Map Saving mode switched on before these functions can be used. After
completing several clean-ups under different lighting conditions, a full map will be
created. When starting a clean-up, please open all the doors in your home to
ensure the integrity of the map.
Do not rely on forbidden areas and virtual walls to isolate dangerous areas.
Moving the robot manually or making significant changes to the home environment
may cause the loss of virtual walls.
Use the mopping function
It is recommended that all floors are vacuumed at least three times before the first
mopping session to achieve better cleaning effect.
1. Install the mop pad: Dampen the mop pad and wiring out excess water. Slide the
pad all the way into the slot of the water tank until it is securely in place.
Select Room
Forbidden Area / Virtual Wall

14
2. Fill the water tank: Open the water tank lid, fill the tank with water, then securely
close the lid.
Note: Do not use non-designated detergents or disinfectants.
3. Install the mopping module: Align the mopping module as indicated by the arrow,
then slide it into the back of the vacuum until it click into place. Press the button
or use Mi Home/Xiaomi Home app to start cleaning.
Note:
Only use the mopping module when someone is at home
To prevent the vacuum-mop from entering carpet areas, objects may be used.
Use the app to adjust the water flow as required.
4. Press the two slide clips inwards and slide the water tank backwards to separate it
from the robot.
Note: When the vacuum-mop is charging or not in use, remove the mopping module, pour
out all remaining water in the tank, and clean the mop pad to prevent mildew or lingering
odors.

15
Routine Maintenance
Dust Bin and Filter
1. Open the vacuum-mop cover, then pitch the bin clips to remove the dust bin.
2. Open the bin cover as indicated by the diagram.
3. Remove the filter, rinse repeatedly and tap the filter frame to remove as much as
dirt as possible.
Note: Do not attempt to clean the filter with a brush or finger.

16
4. Wash the dust bin and filter, with water, and then place it aside to dry fully before
reinstalling it.
Note:
Only clean water should be used to clean the filter. Do not use detergent.
Filter must be fully dry before use (allow at least 24 hours).
Mopping Module
1. Press the side clips of the mopping module inward and pull to remove the module.
Pull the mop pad off the mopping module to remove it.
2. Empty the remaining water in the water tank and keep it dry naturally:

17
3. Clean and dry the mop pad.
Note:
Remove the pad from the mopping module before cleaning it, and make sure dirty
water does not flow back into the water outlet to avoid clogging.
Do not press too hard on the mop pad, as this can hinder its performance.
Pad should be cleaned before each use It is recommended to change the mop pad
every 3 to 6 months.
4. If slow water flow occurs, or the volume is not well-distributed, please clean the air
hole in the cover of the water tank.
Main Brush
1. Flip the vacuum-mop over and pinch the clips to remove the main brush guard. Lift
the main brush out of the vacuum-mop, then clean the brush bearings.
2. Use the included brush cleaning tool to remove any hairs tangled on the brush.

18
Note: If there is a large amount of hair or hair is tightly entangled, remove it carefully to
avoid damage to the main brush.
Side Brush
Flip the vacuum-mop over, then gently pull out the side brush ash shown in the diagram
below to clean it.
Omnidirectional Wheel
Flip the vacuum-mop over and pull out the omnidirectional wheel. Remove hair, dirt, and
other debris from the wheel and axle.
Note: Use tools such as a small screwdriver, etc. to separate the axle and the tire.

19
Use a soft cloth to clean all sensors in the vacuum-mop including:
Visual Navigation Sensor
Infrared Declaration Sensor
Cliff Sensor and Optical Sensor
Clean the contacts of the charging dock with a soft cloth.

20
FAQ
Problem Type
Solution
Vacuum-mop does not turn on
Battery level is low. Recharge the vacuum-mop at
the charging dock, then try again. The ambient
temperature is too low (below 0°) or too high above
(50°C). The operating temperature of the vacuum-
mop is 0°C to 40°C.
Vacuum-mop does not recharge
The charging dock is not receiving power. Please
confirm that both ends of the power cord are
plugged in correctly. Poor contact, clean the
charging contacts of the charging dock and the
vacuum-mop.
Vacuum-mop does not return to
charging dock
There are too many obstructions around charging
dock. Place the charging dock in a more open area.
Vacuum-mop is malfunctioning
Turn of the vacuum-mop and the reactivate it.
Vacuum-mop makes a strange
noise
A foreign object might be caught in the brush, side
brush, or one of the main wheels. Stop the vacuum-
mop and remove any debris.
Vacuum-mop no longer cleans
efficiently or leaves dust behind
The dust bin is full. Please clean it.
The filter is blocked. Please clean it.
A foreign object caught in the brush. Please clean
it.
Vacuum-mop cannot connect to
Wi-Fi
Wi-Fi signal is weak. Make sure the vacuum-mop is
in an area with good Wi-Fi coverage. There is
something wrong with the Wi-Fi connection. Reset
the Wi-Fi and download the latest version of the
app, then try reconnecting.
Vacuum-mop does not perform
scheduled cleaning.
Vacuum-mop has low battery. Scheduled cleaning
will not start unless the vacuum-mop has at least
15% battery left.
Does leaving the vacuum-mop on
the charging dock consume power
if it’s already charged?
Leaving the vacuum-mop on the charging dock
after it’s fully charged consumes very little
electricity and helps maintain optimal battery
performance.
Does the vacuum-mop need to be
fully charged for 16 hours the first
three times it is used?
Lithium batteries do not suffer memory effects, so
it is not necessary to wait 16 hours after fully
charging the vacuum-mop before using it.
No water comes out of the
mopping module, or only a little
bit comes out.
Confirm that the water tank is filled with water and
clean the mop pad id necessary.
Make sure the mop pad is installed correctly
according to the user manual.
Too much water comes out of the
mopping module.
Make sure the water tank lid is securely closed.
Vacuum-mop doesn’t resume
cleaning after charging.
Make sure the vacuum-mop is not set to Do Not
Disturb mode, which will prevent it from resuming
cleaning.
The vacuum-mop does not resume cleaning when it
is manually recharged or placed onto the charging
dock.
Vacuum-mop doesn’t return to
charging dock after being moved
Moving the vacuum-mop may cause it to re-
position itself or re-map its surrounding. If the