Dreame P10 Pro Installation guide

Dreame Support Team
1
Dreame P10 Pro
Cordless Stick Vacuum
FAQ

Dreame Support Team
2
Specs............................................................................................................................................3
Battery......................................................................................................................................... 4
Accessories.................................................................................................................................. 6
Troubleshooting.......................................................................................................................... 8
Precaution....................................................................................................................................9

Dreame Support Team
3
Specs
1. How many suction modes does the P10 pro have?
A: Dreame P10 pro is equipped with three suction modes:
Eco, Med, Turbo.
2. What accessories is P10 pro compatible with, and what are they for?
A：Main brush: Soft roller brush;
Accessory: Mini Motorized Brush, 2-in-1 Crevice Nozzle, Extension Hose;
Soft Roller Brush: for cleaning wood floor, marble, and other hard surfaces.
Mini Motorized Brush: for cleaning dust and pet’s hair on the surface as well as dirt
deep inside a mattress or sofa.
2-in-1 Crevice Nozzle: for cleaning crevices such as corners of walls, doors, and
windows.
Extension Hose: for cleaning areas which are hard to reach like drawer, car seats,
corners under the sofa or bed.
3. What is the weight of P10 pro?
A: Mainly made of ABS engineering plastics, the net weight of the P10 pro main
body
is 1.63kg, the total net weight is 2.62 kg (With extension rod and soft roller brush).
4. What is the battery pack capacity of P10 pro?
A: P10 pro is equipped with seven 2500mAh batteries.
5. What is the highest suction power of P10 pro?
A: The max suction of P10 pro is 130 AW with a vacuum degree of 22 KPa.
6. What is the decibel noise when P10 pro is running?
A: The noise is lower than 84dB(A).
7. What is the motor speed of P10 pro?
A: Powered by the Dreame High-Speed Motor, P10 pro reaches a max motor speed
of up to 120000 rpm.
8. Can P10 pro memorize the suction mode and electronic self-lock after powered
off?
A: Yes.

Dreame Support Team
4
Battery
9. How long can P10 pro operate after fully charged?
Turbo
Med
Eco
With 2-in-1 Crevice
Nozzle
10 min
25 min
60 min
With main
brush
8mins
24min
34min
Mini Motorized Brush
8min
24min
36min
10. How long does it take to fully charge P10 pro?
A: Approximately 3 hours. While charging, LED indicators will flash during charging
and turn solid after fully charged where the circuit disconnects automatically.
11. Can I leave the vacuum and keep it charged all the time?
Yes. After fully charged, the circuit will automatically disconnect to protect the
vacuum from overcharging.
12. What should I do with the batteries if I am not going to use them for a long time?
It is recommended to fully charge P10 pro before storing it in dry and cool places. If
you are going to store it for a long time, we also recommend you to fully recharge it
every 3 months to prevent the battery from over discharging.
13. What is the purpose of the metal contact below the power trigger?
A: It is designed to discharge the static electricity on the surface of the body to
prevent static electricity from hitting the hands. (Completely harmless to human body)
14. Why is the LED indicator off during charging?
1Check if the battery has already been fully charged.
2Check if the adapter is properly connected with the vacuum. If the LED indicator
is still off, contact Dreame Support Team.
15. Why did the P10 pro fail to charge?
If charging failure occur, please try the following steps for troubleshooting.
1. Check if the power plug is properly inserted into the socket.
2. Please make sure the socket is on. If not, please turn it on, if charging still fails,
please contact Dreame Support Team.

Dreame Support Team
5
3. Connect the adapter properly with the main body and check again. If charging still
fails, contact Dreame Support Team.

Dreame Support Team
6
Accessories
16. How to install the P10 pro vacuum?
A: Please refer to the picture below to install the vacuum:
17. How to clean the dust cup and filtration system?
A: Please refer to below pictures:
18. How often do I need to replace the filter? Is the filter washable?
A: Wash: It is recommended to wash the cyclone module, built-in foam and filter in
every 3-4 month before replacing them with a new one.
Dry: Make sure the filter and foam are fully dried for about 24 hours before
installation and use.
19. How to install the Dust Bin Assembly?

Dreame Support Team
7
A: Please refer to the picture below:
20. How to clean and wash the soft roller brush?
A: Please refer to the picture below:
21. How to clean the Mini Motorized Brush?
A: Please refer to the picture below:

Dreame Support Team
8
Troubleshooting
22. What should I do if the vacuum stop working?
A: Please refer to below:
1. Please check whether the battery is dead: Connecting the Vacuum to the adapter for
charging, if it could not charge, please contact the Dreame Support Team.
2. High working temperature caused by blockage will trigger the automatic protection.
If this is the case, please clean the suction port and then reboot the device after it cools
down.
3. Motor damage. If this is the case, please contact Dreame Support Team.
4. if the Vacuum is sucking up liquids, etc., the motor will fail to work. If this is the
case, please contact the Dreame Support Team.
23. Why is the suction power fading?
A: Please refer to below details:
1. Check if there is too much dust inside the dust cup. If yes, clean the dust cup.
2. Check if the extension rod or main body adaptor is clogged. If yes, remove the
foreign matters.
3. Check if the filter is clogged with dust. If yes, clean the filter.
4. If the airduct is not clogged at all, it may be caused by motor issues. Please contact
the Dreame Support Team for repairing.
24. Why does the brush fail move around?
A: Check if the brush is clogged. If yes, remove the foreign matters; if
not, contact Dreame Support Team for help.
25. Why does the vacuum become less responsive to power on?
A: In this case, please contact Dreame Support Team for help.
26. Why does the vacuum heat up rapidly after working for a while?
A: Check if any part of the airduct is clogged. If yes, remove the foreign matters.
Check if there is too much dust accumulated in the filter. If yes, clean the filter.
27. What is cause of the error message on the P10 proScreen? And How to solve it?
A: Please refer to below details:

Dreame Support Team
9
Precaution
28. What could the Vacuum clean?
A:
1. A vacuum can only be used to clean indoor dry surfaces;
2. Do not use the vacuum to clean water, gasoline or any other flammable or
explosive liquid. Do not use it to clean toxic solution, including bleach, ammonia,
drain cleaner and other similar liquid;
3. Do not use the vacuum to clean plaster, fireplace, or ashes. Do not clean any
smoky or burning substance, such as live charcoal, cigarette butts, or matchsticks. Do
not clean sharp objects, such as glass, nails, screws, and coins, otherwise it will cause
damage to the vacuum cleaner.