Drive DeVilbiss Healthcare 1275/PS/HI/EX User manual

Drive Devilbiss Sidhil Ltd, Sidhil Business Park, Holmfield, Halifax, West Yorkshire, HX2 9TN
Tel: [phone] Fax: [phone] Email: s[email protected]
A Member of the Drive Devilbiss Group of Companies
INSTRUC/1275/PS/HI/EX rev0 06/11/17
Thank you for purchasing the Bradshaw Height Extension Side Rail Padding. To install the padding
system please follow the instructions carefully ensuring no steps are missed out.
Installation Procedure
1. Remove padding from protective packaging and dispose of according to local policy.
2. Set the Bradshaw bed at a comfortable working height.
3. Remove all bedding and the mattress, if required, to allow full access to the entire side rail.
4. With pads flat and on a clean level surface identify the head end, foot end*, and inside** of
the pad. *Sewn into the foot end of the “pocket” is a foot end label. **The inside of the pad
faces the patient.
Figure 1 –Inside of Pad (patient side)
5. Ensure all hook and loop fastenings are opened up and place the pad “pocket” over the
height extension.
Figure 2 –Left Hand Pad Fitted to Bradshaw Side Rail Height Extension
Instructions for Use
Bradshaw Height Extension Padding:
1275/PS/HI/EX
Side Rail Pad
“Top Pocket”
A risk assessment must be carried out on a patient by patient basis to
determine suitability of bed and side rail pad.
This and the bed instructions for use must be read and understood fully
before fitting/using the accessory. Incorrect fitment or use could result
in injury or death.
Incorrectly fitted pads can lead to equipment damage or failure.
Warning
Caution
Foot End Hook &
Loop Strap
Lower Rail Flap
Head End Hook
& Loop Strap
Middle Rail Hook
& Loop Straps
Height Extension
Foot End “Leg”of
Height Extension

Drive Devilbiss Sidhil Ltd, Sidhil Business Park, Holmfield, Halifax, West Yorkshire, HX2 9TN
Tel: [phone] Fax: [phone] Email: s[email protected]
A Member of the Drive Devilbiss Group of Companies
INSTRUC/1275/PS/HI/EX rev0 06/11/17
6. Push the two sides of the top pocket together ensuring both sides are aligned and fasten the
hook and loop.
7. Allow the rest of the pad to drop down against the inside (patient side) of the side rails
ensuring that pad sits in-between the mattress platform and the side rail.
8. Wrap & fasten the middle side rail hook and loop straps around the middle side rail.
9. Wrap and fasten the foot end hook and loop strap around the lower side rail ensuring it is in
the correct position as shown in figure 2. This is in-between the foot board and the foot end
“leg”of the side rail height extension.
10. Wrap the lower side rail flap around the lower side rail and fasten together using the zip.
11. Wrap the head end hook and loop strap around the lower side rail and ensure it is the position
as shown in figure 2.
12. Check all straps are tight and pad is in place protecting the bed side rails.
13. Repeat steps 4-12 for the other side rail and pad.
Cleaning Procedure
Routine cleaning for infection control must be carried out in accordance with your local infection
control policy or regulatory body.
The pads should be cleaned by starting with the cleanest parts and systematically moving to the
dirtiest parts. Extra care should be taken around areas where excess dirt or dust may gather.
• The cloth should be changed during the cleaning process if it becomes soiled.
• Wipe down with a clean cloth moistened with a mild detergent and dilute with warm water (40°C).
• Rinse with cold, clean water and a clean cloth, and allow to fully dry before use.
Warranty
A copy of the warranty information can be obtained from a member of the Drive Devilbiss Sidhil Ltd.
customer service team on the telephone number or email shown below.