Drive Trekker TK 1000 User manual

Trekker Gait Trainer
Item #s TK 1000, TK 2000 & TK 3000
www.drivemedical.com
EU Authorized Representative
Drive Medical LTD
Ainley’s Industrial Estate
Elland, West Yorkshire,
United Kingdom HX5 9JP
Lifetime Limited
Warranty
Your Drive brand product is warranted to be free
of defects in materials and workmanship for the
lifetime of the original consumer purchaser.
This device was built to exacting standards
and carefully inspected prior to shipment. This
Lifetime Limited Warranty is an expression of our
confidence in the materials and workmanship of
our products and our assurance to the consumer
of years of dependable service.
This warranty does not cover device failure
due to owner misuse or negligence, or normal
wear and tear. The warranty does not extend to
non-durable components, such as rubber
accessories, casters, and grips, which are subject
to normal wear and need periodic replacement.
If you have a question about your Drive device or
this warranty, please contact an authorized Drive
dealer.
© 2006 Medical Depot, Inc. All rights reserved.
Drive is a trademark of Medical Depot, Inc.
Port Washington N.Y. 11050 USA Made in China

assembly
The TK 1000 comes completely assembled and does
not fold
TK 2000 & TK 3000.
1. Remove the Trekker from the box.
2. Unfold gait trainer by lifting top frame until both
latches click into notches (A) in the bottom frame.
adjustments
Height
Pull triggers (B) upwards and slide handlebar to desired
height. Release trigger and move handlebar until triggers
click into place.
B
A
Swivel Lock
Casters can be locked to prevent swivel. Align lever (C)
with one of the two notches in the caster and push lever
into notch.
Wheel Brake
Pressing on bottom part of brake pedal (D) will lock rota-
tion of wheels. Pressing on top part of pedal will release
brake.
Wheel Resistance
Lever (E) provides resistance to wheels. Rotating the
lever towards the thinner markings lowers the resistance
and towards the thicker markings adds resistance.
Directional Lever
One-direction use can be achieved by pushing lever (F)
upwards. When one-direction is engaged, there will be a
clicking sound when moving forward and the wheel will
lock when rolled backward.
C
D
E
F

accessories
Most accessories are mounted with the universal mount-
ing bracket. To install the mounting bracket, loosen knob
(G) on clamp and lower it. Lift clamp and place over
handlebar. Bring knob up and tighten. The mounting
bracket can be placed anywhere on the handlebar and it
will depend on the user’s abilities. It can also be mounted
towards the outside or the inside of the handlebar.
Forearm Platforms
Item #s TK 1035 S & TK 1035 L
Install mounting bracket and post at appropriate location.
Place forearm platform on mounting bracket post by loos-
ening knob (H) and placing forearm platform at desired
position.
Forearm platform adjustments
Height – Push in button (I) and slide post to desired posi-
tion. Release button and move forearm platform until it
clicks into place.
Width – Forearm platforms can be placed closer or far-
ther from the user by
• Looseningknob(H)andslidingtheforearmplatform
outward or inward.
• Placemountingbracketwiththeclampfacingtowards
the outside or inside of the handlebar.
• Positionforearmplatformposts(J)facingtowardsthe
outside or inside of the handlebar.
Rotation – Loosen knob (H) to rotate up or down and in
or out. It can rotate 360°.
Depth – Loosen knob (H) and slide arm pad forward or
backward or reposition mounting bracket.
• Looseningknob(K)allowsthehandgripstoextend
forward and backward, supinate and pronate.
• Looseningknob(L)allowswristangleadjustability.
• Armstrap(M)andwriststrap(N)securesarm.
Handgrips
Item # TK 1045
Install mounting brackets at appropriate location on the
handlebar. They can be mounted with the clamp facing
towardstheoutsideorinsideofthehandlebar.Toadjust
the height, push in button (I) and slide post to desired
position. Release button and move handgrip until it clicks
into place. Handgrips can rotate in four directions.
KM N
G
I
JHL
G

Ankle Prompts
Item #s TK 1060 S, TK 1060 M & TK 1060 L
Install the ankle prompts by inserting the end of rod into
caster slot, then pull back white trigger (O) and insert
intooppositecasterslot.Toadjustthestrideoftheuser,
press and slide the spring clips (P) to appropriate length.
Toadjustthesizeofanklestrapsusebuckleadjuster(Q).
P P
O
Q
Hip Positioner & Pad
Item #s TK 1070 S & TK 1070
Install mounting bracket and handgrips at the back of the
handlebar. Attach the front of the hip positioner towards
the front of the handlebar using buckles (R). Attach the
rear of the hip positioner towards the rear of the handle-
bar by either attaching rings (S) to handgrips or remove
clamp and handgrips and loop straps over rear of handle-
bar.Adjustloopwithbuckles.
R
T
S
S
U
U
Hip positioner adjustments
Height - rear of the hip positioner - Push in button (T)
and slide handgrip to desired position. Release button
and move handgrip until it clicks into place.
Height – hip positioner – Raise or lower hip positioner by
adjustingthelengthofthetwofrontandtworearstraps.
Depth - Reposition mounting bracket on handlebar.
The hip positioner can be used with or without the pad.
To attach the hip pad, push the rear straps (U) of the hip
positioner through the holes at the back of the pad and
pull into place. Securely snap front and side flaps around
the hip positioner.
REAR
FRONT
T

Trunk Support
Item # TK 1080 S, TK 1080 M & TK 1080 L
Install mounting bracket and post directly behind the
uprights. Loosen knobs (V) on the post and slide chest
prompt rods into the post at desired position. Tighten
knobs.
Trunk support adjustments
Thetrunksupporthastwoadjustablestrapsandbuckles
on each side. The front of the trunk support also has a
restraining loop to keep the pads together. Each strap is
independentlyadjustabletoadjustthesize,fitandangle
of the trunk support.
Height - Push in button (I) and slide post to desired posi-
tion. Release button and move post until it clicks into
place.
Width – Trunk support can be placed closer or farther
from the user by
• Looseningknobs(V)andslidingthetrunksupport
outward or inward.
• Placemountingbracketwiththeclampfacingtowards
the outside or inside of the handlebar
Depth – Reposition mounting bracket on handlebar.
Rotation – Loosen knobs (V) and tilt trunk support to
desired position. Tighten knobs.
V
V
I
X
W
Y
Thigh Prompts
Item #s TK 1090 S & TK 1090 L
Install thigh prompt clamps on handlebar. It is advisable
to mount them behind the trunk support.
Thigh prompt adjustments
Height – Loosen knob (W) and slide thigh pad (X) up or
down to desired position. Tighten knob.
Width – Thigh pads can be placed closer or farther from
the user by
• Looseningknob(Y),adjustthighpadsinwardor
outward and tighten knob
• Placemountingbracketwiththeclampfacingtowards
the outside or inside of the handlebar.
Depth - Reposition mounting bracket on handlebar.
Rotation – Loosen knob (W), rotate the thigh pad and
tighten knob.

www.drivemedical.com
www.drivemedical.com