DTM System Rival 431 User manual

I. General information
II. Receiver characteristics
III. Rival 431 receiver’s instalation
Rival 431 radio receiver is an additional device from the series of ZSP remote control system. It’s a simplified,
one-channel device devoted to gates, rollers and other devices where triggering pulse is needed. ZSP Rival 431 system
allows to broaden functioning of simple gate systems with a remote control in a cheap and easy way.
The receiver cooperates with ZSP series remotes: NEO, TIP and MAKSTER. Radio signal transmission is based on
KeeLoq®standard by Microchip®(dynamically variable code) which gives the best security. KeeLoq®system is
considered to be one of the safest coding systems.
Electric connection must be done according to , which shows receiver with outputs description.
Connector has plugged-in wire-antenna. Also additional antenna can be used. Antenna should be switched into
connectors -( ) middle cable conductor, ( ) cable screen by concentric wire of 50 impedance.
fig.1
W
- dynamically variable code KeeLoq®,
- superheterodyne receiver, frequency 433.92 MHz,
- simple and easy, one-button interface with a built-in LED indicator,
- receiver’s memory containing 15 ZSP remote controls,
- one separated relay NO-type output with max 1A/24V AC or DC,
- operating mode: monostable, about 0.8 second,
- possibility of simple registering remotes, without the necessity of using a receiver's button,
- screw terminal block with the outside access, for connecting cables and outdoor aerial,
- supply voltage: from 12 V to 24V AC/DC,
- maximal current consumption: about 40mA (with relay on),
- tightness level: IP-53, the device devoted to surface mounting,
- working temperature: from –20°C to +55°C,
- dimensions : in case, heigh 118, width 55, depth 27,5[mm]
1
Fig. 1 Receiver with enclosure and connection description
programming button
LED indicator
Antenna
( )
( )
12...24V AC/DC
C1 (NO)
Legend:
1. weakening for wires in bottom part of enclosure (inside
instalation),
2. weakenings for receiver mounting,
3. clip to hold wire,
4. chamber for electric plate,
5. wire clip clousure,
6. distance sleeve for plate mounting
układu elektronicznego (screw 2,2 x 6,5),
8. case closing openings,
7. weakening for wires in top part of enclosure (surface
instalation),
3
4
5
1
2
6
7
8
39 mm
102 mm
ZSP Rival 431
A radio receiver for gate controllers
2
1
3
4
MADE IN
POLAND

IV. Receiver’s programming
1) Registering a new remote
While holding the receiver’s button, press a button in the remote which you want to register. The light will blink.
- If you hold the receiver’s button for too long, all remotes will be removed from the receiver’s memory,
- You can’t register more than 15 remotes.
This useful function allows adding a new remote to the receiver’s memory without using the receiver’s button. The
feature is useful only if some registered remote is available and it is within the receiver’s radio range.
a) press and hold button in previously registered remote for 15 seconds,
b) press and hold button in a remote which you want to register for 15 seconds, within 3 seconds after releasing the previous
button,
c) the new remote is now registered with the same active button as in the previously registered remote.
- failure in registering may be caused by low batteries, radio interferences or full memory of the receiver.
Press the active button in the remote while holding the receiver button. The light will fade then.
- if you hold the receiver’s button for too long, all remotes will be removed from the receiver’s memory.
Press and hold the receiver’s button for 10 seconds. Release the button when the light fades.
While registering the remote in the receiver’s memory, the button controlling the output channel must be used. Only one
button of the remote can be registered. Registering another button of the same remote will result in removing the previous
one.
Remarks:
2) Registering a new remote without using receiver’s button
Remarks:
3) Removing a remote
Remarks:
4) Removing all remotes
V. Specification of ZSP remotes
- KeeLoq®system,
- 2 buttons (4 buttons in NEO4P),
- Working frequency: 433.92 MHz,
- Battery L1028 23A 12V,
-TIP remote range: up to 50m, NEO remote range up to 150m,
- ERP: 1mW (TIP), 3mW (NEO),
- working temperature: from 0°C to +55°C.
VI. Warranty
DTM System checks all the devices before shipping. The
warranty time is 24 months from the selling date. This time is counted
according to the warranty label. The manufacturer will fix all the
problems which come because of his fault. Non functioning device
should be delivered back to the distributor with short problem
description. The cost of mount/dismount is on user's own expense. The
warranty do not cover: batteries in the remotes, faults caused by
improper usage, user self repairs and adaptations, lightning strikes, over
voltages or short circuits in the mains supply. Appropriate legal acts
regulates details of the warranty.
The intention of the WEEE Directive (Directive 2002/96/EC on waste electrical and electronic equipment) is to reduce the amount of
hazardous substances in waste. The underlying purpose is to promote the avoidance, recovery and risk-free disposal of waste.
2
1
3
4
2
1
2
Declaration of conformity Nr
02/2009
Product is compatible with European Directives:
R&TTE 99/5/EC
Bydgoszcz, Poland 01-08-2009
www.dtm.pl
DTM System, ul. Brzeska 7, 85-145 Bydgoszcz