Duevi VV-ZELA-RB-868 User manual

VV-ZELA-RB-868 21.09-M:2.2-H:4a/4b-F:0.27+
VV-ZELA-RB-868 Battery powered outdoor wireless siren
VV-ZELA-RB-868 is a self-powered outdoor wireless siren
with a high-power magnetodynamic horn, used for external
alarm signaling, indicating the arming and disarming of the
system.
PLEASE NOTE. Before definitively fixing the
siren, carry out some transmission tests towards
the control panel to check that the position is
adequate.
1. Identification of parts
Figure 1 –Identification of parts
Figure 2 –Electronic board
REFERENCES ELECTRONIC BOARD
TMP
Tamper connector
SIR
Trumpet magnetodynamic connector
BAT
Battery Connector
ANT
Antenna Connector
DIP-SWITCH
Switches for settings
LED1-2-3-4
High power LEDs for signaling
2. Dip-switch
DIP
Function
OFF
ON
1
Mode
Normal
operation
Wireless enroll
2
Tamper
DISABLED
Siren tamper
does not make
the siren sound
ENABLED
Siren tamper
makes the siren
sound
3
Control
Panel Model
CE-LAN
EZY-LAN
4
NOT USED
LEAVE OFF
5
6
7
8
PLEASE NOTE. The position of DIP3 (for the
selection of the panel model) is checked only
when the siren boot. In case of modification
disconnect the battery, wait a few minutes and
reconnect the battery.
3. Wireless enroll
To enroll the siren on the control panel (CE-LAN or EZY-
LAN), proceed as follows:
1. Log in as INSTALLER on the control panel
2. Enter SETUP> DEVICES> ADD NEW DEVICES. The
control unit waits for the sensor to be enrolled
3. Enter ENROLL MODE on the siren (DIP1 = ON)
4. Press the siren TAMPER button (9)
5. Check that the control panel has learned the code
6. Exit the ENROLL MODE on the siren (DIP1 = OFF)
To confirm that the siren has been learned, two beeps will
be issued accompanied by the flashing of the siren LEDs. In
case of missed learning repeat the operation.
4. Settings
Once the siren is enrolled, it is possible to set its sound
functions directly on the control panel setup.
Follow the control panel manual for details

5. LEDs signals
The LEDs on the device provides the following indications:
•Continuous flashing during alarm
•One long flash during arming (if enabled in the control
panel)
•Three short flashes during disarming (if enabled on the
control panel)
6. Operation
The siren is bidirectional, therefore it receives and transmits
radio packets to communicate with the alarm control panel
and act accordingly. Each transmission waits for a
confirmation response, otherwise it is repeated.
The siren emits audible and visual alarm alerts.
Radio information sent by the control panel:
•System armed / disarmed
•Entry / Exit from SETUP
•High level alarm (High power sound)
•Low level alarm (Sound with intermittent beeps)
•End of alarm (Siren silence)
Radio information sent by the siren:
•Tamper manumission
•Battery level
•Supervision
7. Auto-protection
The device is equipped with anti-opening and anti-removal
protection. If enabled, the tamper alarm is active 24H, even
when the system is disarmed (excluding the case in which
the control panel is in "SETUP").
When the siren cover is opened, the tamper code is sent to
the control unit and both start to ring.
Once the tamper alarm has been triggered, it is disabled
until the next ARMING of the system.
Following a tamper alarm, it is therefore necessary to arm
the system at least once to reactivate it.
NOTE: when the siren is new to enable the
tamper it is necessary to perform at least one
arming.
8. Battery
The battery level is constantly monitored and sent to the
control panel. The status of the battery can be viewed in real
time on the Software / Application. In case of low battery,
the control panel records it as an event and, if programmed,
notifies the user.
When replacing the battery it is important to place it away
from the antenna, in fact if the battery is placed near the
antenna it could reduce the range. For correct battery
installation, refer to figure 1.
CAUTION:
DANGER OF EXPLOSION IF THE BATTERY IS
REPLACED BY ANOTHER INCORRECT TYPE.
DISPOSE OF USED BATTERIES FOLLOWING
THE INSTRUCTIONS.
9. Warnings and precautions
•The installer must follow the current regulations. The
manufacturer declines all responsibility in the event of
improper use by the user or incorrect installation by the
installer
•Handle the battery carefully. Explosion and fire hazard.
Do not throw the battery into a fire, do not weld or
damage the battery. Replace the battery only with one
of the same type. Have the battery replaced by a
specialized technician
•Dispose of used batteries according to the regulations
in force, even if the equipment is no longer in use. In
case of leakage of liquid, protect your hands with special
gloves
10.Technical features
Power supply
Lithium battery pack 7,2V - 13Ah (mod.
BAT7V2LITIO)
Consumption
Stand-by: about 50 µA
Alarm: about 850 mA
Battery life
About 2 years (4 activations per day + 50 alarms).
Alarm limitation
max 5 alarms for each arming
Alarm duration
Limited to max 90 seconds (settable on the control
panel)
Acoustic power
115 dB / m
System status
reports
ARMING →long flash + 1 beep (programmable on
panel)
DISARMING →3 short flashe + 3 beeps
(programmable on panel)
Frequency
869,650 MHz
Radio range
200m (open field)
Temperature
-5°C / +45°C
Dimensions
310 x 210 x 85 mm (HxLxP)
DUEVI SRL
Via Bard 12/A –10142 Torino
MADE IN ITALY
EU DECLARATION OF CONFORMITY
Hereby, DUEVI declares that the radio equipment type
“Battery powered outdoor wireless siren” mod. VV-ZELA-
RB-868 is in compliance with Directive RED 2014/53/EU.
The full text of the EU Declaration of Conformity is
available at the internet address www.duevi.eu