Duke HOT/FROST HF35-2 User manual

Installation and
Operation Manual
HOT/FROST®
Models:
HF35-2
HF48-2
HF50-2
HF64-2
HF91-2
This manual is Copyright © 2018 Duke Manufacturing Co. All rights reserved.
Reproduction without written permission is prohibited. Duke is a registered
trademark of the Duke Manufacturing Co.
P/N 568974
REV A 9/13/2018
CAUTION: Please read this manual completely before attempting
to install, operate or service this equipment

2
Installation and Operation of: Hot/Frost
IMPORTANT SAFETY INSTRUCTIONS
Throughout this manual, you will nd the following safety words and symbols that signify
important safety issues with regards to operating or maintaining the equipment.
Indicates a hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION
Indicates a hazardous situation which, if not avoided, could
result in minor or moderate injury.
CAUTION
Indicates Important Information
Indicates electrical shock hazard which, if not avoided, could
result in death or serious injury and/or equipment damage.
Indicates hot surface which, if not avoided, could result in
minor or moderate injury.
TABLE OF CONTENTS
Important Safety Instructions............................................................................................................................ 3
Product Specications.......................................................................................................................................... 4
Unit Inspection........................................................................................................................................................ 5
Un-crating Unit ....................................................................................................................................................... 5
Installing Unit .......................................................................................................................................................... 7
Operations ................................................................................................................................................................ 8
Cleaning..................................................................................................................................................................... 9
Maintenance ..........................................................................................................................................................10
Wire Diagrams .......................................................................................................................................................11
Congratulations on the purchase of your new Hot/Frost unit. Please read this manual
completely before installing or working on your new unit.

3
Installation and Operation of: Hot/Frost
In addition to the warnings and cautions in this manual, use the following guidelines for
safe operation of the unit.
• Read all instructions before using equipment.
• For your safety, the equipment is furnished with a properly grounded cord connector. Do
not attempt to remove or disconnect the grounded connector.
• Install or locate the equipment only for its intended use as described in this manual.
• Do not use corrosive chemicals on this equipment.
• Do not operate this equipment if it has a damaged cord or plug, if it is not working
properly, or if it has been damaged or dropped.
• This equipment should be serviced by qualied personnel only. Contact the nearest
Duke authorized service facility for adjustment or repair.
• Do not block or cover any openings on the unit.
• Do not immerse cord or plug in water.
• Keep cord away from heated surfaces.
• Do not allow cord to hang over edge of table or counter.
The following warnings and cautions appear throughout this manual and should be
carefully observed.
• Turn the unit o, disconnect the power source and allow unit to cool down before
performing any service or maintenance on the unit.
• The procedures in this manual may include the use of chemical products. You must read
the Material Safety Data Sheets before using any of these products.
• The unit should be grounded according to local electrical codes to prevent the
possibility of electrical shock. It requires a grounded receptacle with dedicated electrical
lines, protected by fuses or circuit breaker of the proper rating, in accordance with all
applicable regulations.
• Disposal of the unit must be in accordance with local environmental codes and/or any
other applicable codes.
• This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance
by a person responsible for their safety.

4
Installation and Operation of: Hot/Frost
SPECIFICATIONS
Model AMPS HP Refrig.
404A
HFL -208 FOL-120
NEMA NEMA
HF35-2 9.4 2lb 14.5oz L14-20P 5-15P
HF48-2 9.6 3lb .5oz L14-20P 5-15P
HF50-2 13.4 2lb 14.5oz L14-20P 5-15P
HF64-2 19.4 3lb .5oz L14-30P 5-15P
HF91-2 26.8 1lb 14.5oz L14-30P 5-15P
DIMENSIONS:
ELECTRICAL SPECIFICATIONS: 120-208V, 1P, 60Hz
Model Overall Length Cutout Length Overall Depth Cutout Depth
in cm in cm in cm in cm
HF35-2 35.0 88.9 33.375 84.77 24.00 60.96 20.813 52.87
HF48-2 48.125 122.24 46.625 118.43 32.00 81.28 28.813 73.19
HF50-2 50.125 127.32 48.5 123.19 24.00 60.96 20.813 52.87
HF64-2 64.25 163.20 62.625 159.07 24.00 60.96 20.813 52.87
HF91-2 92.875 235.90 91.25 231.77 24.00 60.96 20.813 52.87
45.243
OVERALL LENGTH DEPTH

5
Installation and Operation of: Hot/Frost
UNIT INSPECTION AND UNCRATING
INSPECTING UNIT
• Inspect the shipping carton and/or
container, carefully noting any exterior
damage on the delivery receipt
• Crating has SHOCK WATCH labeling to
indicate improper handling of unit.
• Note any damage not evident on the
outside of the shipping container
(concealed damage). Contact the carrier
immediately and le a damage claim with
them.
• Save all packing materials when ling
a claim. Freight damage claims are the
responsibility of the purchaser and are
not covered by the warranty.
• Report any dents or breakage to source
of purchase immediately.
• Do not attempt to use unit if damaged.
CAUTION
Step 1
Remove all crating material from around the
unit.
Do not remove any support system from under the
unit. Doing so could result in damage to unit and/ or
personal injury.
CAUTION
Installation of this unit requires more than one person.
To Lift Unit
To Lift Unit
UN-CRATING

6
Installation and Operation of: Hot/Frost
UNCRATING UNIT  continued
CAUTION
If boards are not up against pylons damage to light or
heaters could result.
Step 4
Position lifting forks under the middle shelf.
Position the two (2) 2x4 boards the length of
the unit one on each side of the pylons.
CAUTION
NOT following this step will cause damage to the
sneeze guards and heaters on the unit.
Step 3
Remove the two (2) wood screws holding
two (2) 2x4 boards marked,“TO LIFT UNIT”.
These boards will be used to remove unit
from crate.
Step 2
Remove outer protective shrink wrap and
cut banding.
To Lift Unit

7
Installation and Operation of: Hot/Frost
Step 5
Making sure the boards are held against the
pylons slowly lift the unit from the crate.
Be cautious of the power cord and the
refrigerant lines at each end of the unit.
Step 1
In the same manor slowly lower the unit into
the counter.
NOTE: Be cautious of the power cord and
the refrigerant lines at each end of the unit.
INSTALLING UNIT
UNCRATING UNIT  continued
CAUTION
Step 2
Make sure unit is set square in counter, then
run a small bead of silicone around counter
top and base of unit.

8
Installation and Operation of: Hot/Frost
OPERATIONS
HOT SHELF
• Flip switch to HOT
• The amber light will come on
• Turn the Hot Control Knob to the desired level of heat
• Unit will begin to heat
COLD SHELF
• Flip the switch to COLD
• The green light will come on
• Top will begin to frost over
LIGHTS
• For lights ip switch to ON
CONTROL PANEL

9
Installation and Operation of: Hot/Frost
CLEANING
General cleaning
• Always clean equipment thoroughly before rst use.
• Clean unit daily, using warm, soapy water or mild detergent.
• A plastic scouring pad and a mild detergent may be used to remove hardened food.
• Turn o unit at breaker before doing extensive refrigeration compartment cleaning or
servicing.
NOTICE:Do not ever use steel wool, any highly caustic cleaners, acids or ammonia.
These may cause corrosion and/or damage to the stainless steel.
• Turn OFF power switch and disconnect unit from power source before performing
any cleaning, adjustments or maintenance.
• DO NOT submerge or saturate with water. Unit is not waterproof.
• This unit is not “jet proof” construction. Do not use jet clean spray to clean this unit.
• Do not stem or use excessive water on unit.
• This unit must be serviced by qualied personnel only. Service by unqualied
personnel may lead to electric shock or burn.
• FIRE HAZARD: Do not use ammable cleaning solutions to clean this unit.
Daily Cleaning
• Move the Power I/0 (on/o) Switch to the “O” (o ) position and allow the unit to defrost.
NO TE: If a catch pan is used underneath the drain tting, make sure the pan is emptied reg-
ularly to prevent overowing.
• Remove and wash any pans.
• Clean the frost top using a damp cloth or sponge and mild detergent. Use a plastic scour-
ing pad to remove any hardened food particles or mineral deposits.
• Wipe down the frost top with a non-abrasive, sanitized cloth to remove the detergent
residue.
• Repeat until all detergent residue is gone and the frost top is clean.
• Wipe down the outside of the ventilation panels where the condensing unit is installed.
• Wipe dry the entire unit and the ventilation panels with a clean, non-abrasive cloth.
Stainless Steel
• A soft cloth and clean, soapy, warm water should be used.
• A nal rinse with clean water and a dry wipe with the grain will complete the process.
Lexan
• Prepare a cleaning solution using warm water and a liquid dish soap.
• Use a soft cloth or a microber cloth to clean.
• Rinse with lukewarm water. Wipe the surface dry with a microber cloth.
• Never use scrapers, squeegees or solutions made for glass.

10
Installation and Operation of: Hot/Frost
Monthly Cleaning
Perform the following procedure monthly to maintain proper and ecient operation as well
as prevent malfunction of the condensing unit.
1. Remove and clean both sides of the ventilation panels that are located where the
condensing unit is installed. Dirt and dust build-up in the panels can restrict air ow to
the condensing unit and cause over-heating.
2. Clean the condenser coil cooling ns. Dirt, dust, and lint build-up in the cooling ns will
prevent proper cooling of the refrigerant in the refrigeration system. This buildup will
cause inecient operation and can lead to unit failure. Use the following methods to
clean the condenser coil cooling ns:
• Vacuum the cooling ns.
• Brush the cooling ns vertically using a condenser coil brush.
3. Clean fan blades
4. Clean and disinfect drain lines with a solution of warm water and bleach.
NOTE: Use caution when brushing the cooling ns, they are delicate and can be bent easily.
DO NOT use a wire brush.
MAINTENANCE
• Turn OFF power switch and disconnect unit from power source before performing
any cleaning, adjustments or maintenance.
• DO NOT submerge or saturate with water. Unit is not waterproof.
• This unit is not “jet proof” construction. Do not use jet clean spray to clean this unit.
• Do not stem or use excessive water on unit.
• This unit must be serviced by qualied personnel only. Service by unqualied
personnel may lead to electric shock or burn.
• FIRE HAZARD: Do not use ammable cleaning solutions to clean this unit.
Condenser Coil
Cooling Fins
NOTE: Depending on the conditions of the
installation site, this cleaning procedure
may need to be performed more often or
less often than monthly. Monitor the level of
dirt, dust, and lint buildup on the panels and
cooling ns, and make adjustments to the
frequency of cleanings as necessary.

11
Installation and Operation of: Hot/Frost
L1
L2
L3
N
Lower Shelf Refrig. Valve
1 2
1 2
Top Shelf Refrig. Valve
1 2
1 2
Power Box (Under Shelf)
COMPRESSOR
CONDENSER
FAN
REFRIGERATION CONSTANT PRESSURE SW.
ON
Plug Block
12" 4.2W
LED Light Shelf Light
Power Switch
ADDITIONAL
LIGHTS
Light Power
Supply
Power Connect
Block
ON
Plug Block
12" 4.2W
LED Light
Shelf Light
Power Switch
ADDITIONAL
LIGHTS
L1
L2
L3
N
Shelf Heat
Power Box (Under Shelf)
L1
L2
L3
N
COLD OFF
Lower Shelf Refrig. Valve
COLD
Light
Shelf Option – Frost
(w/o Heat Option)
1 2
1 2
Power Box (Under Shelf)
COMPRESSOR
CONDENSER
FAN
REFRIGERATION CONSTANT PRESSURE SW.
Shelf Option – Heat (w/o Frost Option)
WHT
BLK
BLK
WHT
BLK
WHTBLK BLK
BLK
WHT
BLK
BLK
BLK
RED
WHT
BLK
BLK
BLK
BLK
RED
RED
BLK
WHT
WHT
RED
WHT
WHT
WHT
BLK
WHT
BLK WHT
Top Shelf
ELC0116 Rev. C 08/30/2018
Hot & Frost Configuration - Top & Lower Shelf
RED
BLK
COLD
Light
Dial
Infinite Switch HOT
Light
Rear Element
Front Element
Top Shelf Heat
COLD
CENTER
OFF
HOT
BLK
BLK
ORN BLK RED
BLK
BLK
GRN
GRN
RED RED
RED
BLK
YEL
BRN
BLK BLK
RED
BLK
WHT
BLK
COLD
Light
Dial
Infinite Switch HOT
Light
Rear Element
Front Element
COLD
CENTER
OFF
HOT
BLK
BLK
ORN BLK RED
BLK
BLK
GRN
GRN
RED RED
RED
BLK
YEL
BRN
BLK
BLK
RED
Lower Shelf
Lower Shelf Heat
Dial
Infinite Switch HOT
Light
Rear Element
Front Element
BLK BLK
ORN BLK RED
GRN GRN
RED RED RED
BLK
YEL
Lower Shelf Heat
RED
BLK
H2 H1 L2 P
L1
RED
Wiring Diagram – Duke Hot Frost
(HF Models)
H1
PILOT L1
H2
L2
TOP
Dial Infinite Switch
H2 H1 L2 P
L1
H2 H1 L2 P
L1
M odel Top Shelf Heat
(Option)
Lower Shelf Heat
(Option)
HF35 Front: 24", 350W
Rear: 30", 450W
Front: 24", 350W
Rear: 30", 450W
HF48 Front 42", 675W
Rear: 36", 575W
Front 42", 675W
Rear: 36", 575W
HF50 Front: 42", 675W
Rear: 42", 675W
Front: 42", 675W
Rear: 42", 675W
HF64 Front: 54", 925W
Rear: 60", 1050W
Front: 54", 925W
Rear: 60", 1050W
HF91 Front: 54" & 30",1375W
Rear: 54" x 30", 1375W
Front: 54" & 30",1375W Rear: 54" x 30", 1375W
Heat Element Configurations
HOT FROST WIRE DIAGRAMS

Installation and Operation of: Product Name
Duke Manufacturing Co.
2305 N. Broadway
St. Louis, MO 63102
Phone: [phone]
Toll Free: 1-800-735-3853
Fax: [phone] www.dukemfg.com
L1
L2
L3
N
Lower Shelf Refrig. Valve
1 2
1 2
Top Shelf Refrig. Valve
1 2
1 2
Power Box (Under Shelf)
COMPRESSOR
CONDENSER
FAN
REFRIGERATION CONSTANT PRESSURE SW.
ON
12" 4.2W
LED Light Shelf Light
Power Switch
ADDITIONAL
LIGHTS
Light Power
Supply
ON
12" 4.2W
LED Light
Shelf Light
Power Switch
ADDITIONAL
LIGHTS
BLK
RED
WHT
BLK
BLK
BLK
BLK
RED
RED
BLK
WHT
WHT
RED
WHT
WHT
WHT
BLK
WHT
BLK WHT
Top Shelf
ELC0252 Rev. A 11/20/2017
BLK
COLD
Light
Dial
Infinite Switch HOT
Light
COLD
CENTER
OFF
HOT
ORN BLK RED
BLK
BLK
YEL
BRN
BLK BLK
RED
BLK
WHT
BLK
COLD
Light
Dial
Infinite Switch HOT
Light
Rear Element
Front Element
COLD
CENTER
OFF
HOT
BLK
BLK
ORN BLK RED
BLK
BLK
GRN
GRN
RED RED
RED
BLK
YEL
BRN
BLK
BLK
RED
Lower Shelf Heat
Wiring Diagram – Duke Hot Frost
91" Models
H2 H1 L2 P
L1
H2 H1 L2 P
L1
120Vac
Coil
N.C.
N.O.
BLK BLK
BLK
WHT
BLK
BLK BLK
Plug Block
Power Connect
Block
Plug Block
BLK
BLK
RED RED
RED
BLK
120Vac
Coil
N.C.
N.O.
BLK BLK
BLK
WHT
BLK
BLK BLK
Bottom Shelf
H1
PILOT L1
H2
L2
TOP
Dial Infinite Switch
RED RED
RED RED
NO
NC
COM
COIL
BLK – Output to
Heater Splice
WHT – Frost
Light ‘N’ Splice
BLK – H1
Output Splice
BLK – Power
Switch L1
Relay Connections
HOT FROST WIRE DIAGRAM  Model HF91-2 Only