DURAVIT Starck 3 030160 User manual

Installation instructions Washbasin
MI_Allg_WT_51193_21_03_3.indb 1MI_Allg_WT_51193_21_03_3.indb 1 23.06.2021 09:53:3723.06.2021 09:53:37

2MAL_51193/21.03.3
MI_Allg_WT_51193_21_03_3.indb 2MI_Allg_WT_51193_21_03_3.indb 2 23.06.2021 09:53:3723.06.2021 09:53:37

MAL_51193/21.03.3 3
Important information 4
Installation 10
MI_Allg_WT_51193_21_03_3.indb 3MI_Allg_WT_51193_21_03_3.indb 3 23.06.2021 09:53:3723.06.2021 09:53:37

en
4MAL_51193/21.03.3
About these instructions
These mounting instructions come as part of the Duravit
washbasin and are to be read carefully prior to the installation.
Target readership and qualifications
This is a professional grade product. A working knowledge
of construction techniques and code compliant plumbing
installation are required for proper installation and user
satisfaction. The product must be installed by a licensed
plumber.
Explanation of the signal words and symbols
NOTE! To avoid property damage
Link to the mounting instructions in this
section
Inspection (e.g. for scratches)
Check for leaks and leak-tightness
Indication of the length of time (e.g. 10
minutes)
Safety instructions
Product and/or property damage
The breach of local and country-specific regulations and
standards can cause damage to the product and/or property
damage.
> Observe the local installation regulations and any
country-specific standards at all times.
Prior to installation
Please read the specifications sheets prior to installation.
Specification sheets are available for download at
www.pro.duravit.us.
Products are in compliance with the following codes:
• Uniform Plumbing Code (UPC®)
• National Plumbing Code of Canada
• Following standards: ASME A112.19.2/CSA B45.1
MI_Allg_WT_51193_21_03_3.indb 4MI_Allg_WT_51193_21_03_3.indb 4 23.06.2021 09:53:4123.06.2021 09:53:41

MAL_51193/21.03.3 5
The washbasin will include mounting hardware model # 695100 0000.
The plastic anchors provided are for concrete wall applications. For wood stud walls,
the lag bolts should be screwed into the wood backing.
#
695100 0000
Delivery contents
MI_Allg_WT_51193_21_03_3.indb 5MI_Allg_WT_51193_21_03_3.indb 5 23.06.2021 09:53:5223.06.2021 09:53:52

6MAL_51193/21.03.3
The washbasin specification sheet will
provide the recommended mounting
height and show the location of the
mounting holes. (The height can be
adjusted to your personal preference)
> Mark the location of the mounting
holes.
> Using the appropriate bit for the
wall material, drill pilot holes.
55
A
B
When mounting the washbasin on a
pre-wall carrier, install the mounting
bolts to the element.
When mounting the washbasin
into a wood stud wall,
there must be adequate bracing.
We recommend doubling up
2x6‘s or 2x8‘s between the studs
to form a solid anchoring point.
Reference the washbasin
specification sheet to establish
the height and the spacing
of the mounting bolts.
Washbasins with siphon cover
> Continue with mounting A
Washbasin with pedestal
> Continue with mounting B
X
X
X
X
Ø
9
/
16
"
Ø 14 mm
A1 A2
MI_Allg_WT_51193_21_03_3.indb 6MI_Allg_WT_51193_21_03_3.indb 6 23.06.2021 09:54:0023.06.2021 09:54:00

MAL_51193/21.03.3 7
> Leveling the washbasin: the white
plastic sleeves protect the china
from the metal bolt and allow for
slight adjustment in the height of
the washbasin to level it.
> Apply silicone around washbasin
edges.
> Install faucet and trap assembly
according to manufacturer’s
installation instructions.
Please note if the washbasin will
be mounted on a concrete wall
application, anchors must be used.
> Screw mounting bolts into the
pre-drilled holes with an adjustable
wrench.
> Screw in the full length of the
mounting bolt, so the lag thread is
no longer visible.
> Install Shut off valves according
to manufacturer’s installation
instructions.
> Carefully slide washbasin onto the
mounting bolts.
> Insert white plastic sleeve over
the bolt and into the hole of the
washbasin.
> Install provided washer and nut.
> Hand tighten the nut so the
washbasin is secure.
A6 A7 A8
A5A3 A4
MI_Allg_WT_51193_21_03_3.indb 7MI_Allg_WT_51193_21_03_3.indb 7 23.06.2021 09:54:0423.06.2021 09:54:04

8MAL_51193/21.03.3
> Mark the location of the mounting
holes.
> Mark the location of the back edge
where the washbasin meets the
wall.
Pedestal
Note!
Pedestal may only be installed with corresponding listed washbasin.
> Scan QR Code on packaging label or visit the webadress
qr.duravit.com/”articlenumber” to get listed washbasin.
> Using the appropriate bit for the
wall material, drill pilot holes.
Please note if the washbasin will
be mounted on a concrete wall
application, anchors must be used.
> Screw mounting bolts into the
pre-drilled holes with an adjustable
wrench.
> Screw in the full length of the
mounting bolt, so the lag thread is
no longer visible.
> Set washbasin on pedestal leg
carefully, then using a level,
properly align the washbasin.
Ø ⅝"
Ø 14 mm
B4B2 B3
B1
#...., #...., #....,
#...., #...., #....,
#...., #...., #....,
#...., #...., #....,
#...., #...., #....,
#...., #...., #....,
#...., #...., #....,
#....
+
MI_Allg_WT_51193_21_03_3.indb 8MI_Allg_WT_51193_21_03_3.indb 8 23.06.2021 09:54:0823.06.2021 09:54:08

MAL_51193/21.03.3 9
> Install Shut off valves according
to manufacturer’s installation
instructions.
> Carefully slide washbasin onto the
mounting bolts.
> Insert white plastic sleeve over
the bolt and into the hole of the
washbasin.
> Install provided washer and nut.
> Hand tighten the nut so the
washbasin is secure.
> Leveling the washbasin: the white
plastic sleeves protect the china
from the metal bolt and allow for
slight adjustment in the height of
the washbasin to level it.
> Install the faucet according to
the corresponding installation
instructions.
> Install the siphon according to
the corresponding installation
instructions.
> Turn on Shut off valves to test water
flow to faucet and drain.
B8 B9 B10
1
2
B5 B6 B7
MI_Allg_WT_51193_21_03_3.indb 9MI_Allg_WT_51193_21_03_3.indb 9 23.06.2021 09:54:1323.06.2021 09:54:13

10 MAL_51193/21.03.3
> Test faucet and drain to ensure
there are no leaks.
> Test faucet and drain to ensure
there are no leaks.
> Apply silicone around washbasin
edges.
> Gently lift the front of the
washbasin to allow pedestal to
slide underneath. Slightly loosen
mounting if needed to allow for safe
lift of basin lip.
> Tighten mounting bolts with wrench
to secure. Inspect and adjust for
proper level.
> Washbasin should sit snug upon
pedestal base.
1
2
B11
B14
B12
B15
B13
MI_Allg_WT_51193_21_03_3.indb 10MI_Allg_WT_51193_21_03_3.indb 10 23.06.2021 09:54:1723.06.2021 09:54:17