DUSK Melrose User manual

Important
Assembly Tip
Before you begin, it's best to identify all of the parts and fittings to build your ottoman bed
frame. We advise laying these out on the floor to check you have everything, and
to familiarise yourself with all of the parts and fittings before building.
Top Tip
We recommend that you build your new ottoman bed frame in the room you'd like it to be
located. This will help prevent any risk of damage to the frame whilst moving it.
Safety and Care
It's important to ensure children and animals are kept away from the assembly area, as there
are small components used in this bed frame which could present a choking
hazard.All plastic and wrapping materials should also be kept away from children
and animals to prevent any risk of suffocation.
Help and Support
Please contact our customer service team on 0113 519 0311 if you have any questions or
issues with your purchase.
Recycling
Please ensure that packaging is disposed of in a safe and environmentally friendly way,
and recycle where possible. Please keep your assembly instructions safe to refer back to
in the future.
Page 2

Note：The frame can be lifted from either left or right side,
please choose the side you desire when assembling the bed
.
Step 1: Attaching the Lift Mechanisms to the Headboard &
Footboard

Step 2: Attaching the Bolts to the Headboard & Footboard
The image follows on from 1a (right side), if you are building the bed to open on the
other side than shown, please follows the instructions in the opposite direction.

Step 3: Attaching the Left & Right Side Rails to the Headboard &
Footboard, attaching the holding blocks to the side rails.
8pcs
1pc
1%%HIRUHWLJKWHLQJWKHEROWVSOHDVHHQVXUHWKHEHGIUDPHLVVTXDUH Page 7
WRONG
CORRECT

Step 4 : Attaching the Central Support Rail & Angle Corner Brackets

Step 5 : Attaching the Fabric Base & Legs
Fit the fabric base along the
velcro on the base of bed frame.
Make sure the side of the fabric base with 2 holes
is attached to the footboard and attach the legs
through the 2 holes to the footboard.
Page 8
1
7
1
5

Step 6: Attaching the Ottoman Metal Frames to the Side Ottoman
Metal Frame, conect the Central Support Rail to the Ottoman Metal
Frames

Step 7: Attach the horizontal support rails (8) to the ottoman metal frames
and the use blots to connect the ottoman metal frames to each lift
mechanism.

Step 8: Attaching the Slat Caps to the Ottoman Bed Frame

Step 9: Attaching the Gas Stuts to Lift Mechanisms
Note: if you are having issues with closing your bed frame and the gas struts Page
10 please seek advice on the last page.

Care and Maintenance
Here are some good tips to keep your new ottoman bed frame in tip-top condition.
Cleaning
To clean your new ottoman bed frame, we advise using a damp cloth if the fabric is
dusty or a low suction vacuum. Do not use abrasive chemicals or bleach as this may
damage the product.
Checking and moving
Periodically, we recommend you check that the screws and fixtures haven't become
loose over time. To move your bed frame, we recommend lifting it where possible, as
dragging or pushing it could cause damage to the legs or flooring.
Fabric
Please note, depending on the Iighting, positioning and surroundings of your room,
the shade of the fabric will appear differently. Over a period of time, the fabric may
also lighten or fade slightly due to light exposure.
Page 11

Gas strut/piston best use:
·Use caution when operating - always use two hands.
·Only attempt to close the ottoman frame, once the mattress has been placed on the frame.
·The thicker side of the cylinder should be above the thinner side - this will increase longevity ofthe
part.
·Only attempt to close the frame with two hands from the footboard side, slowly increasing the
pressure until the frame starts moving downwards.
·Closing the frame for the first time may be difficult, as the cylinder needs cycling and lubricating.
After closing for the first time, open and close a further 5 times.
·If the frame is stuck open and unable to be closed, we recommend getting assistance from a second
person, both applying equal pressure from each side of the footboard until the frame closes, this may
require more force than expected. Stop applying pressure if the metal frame begins to warp – contact
customer services at this point.
Top tips:
·Do not attempt to close the gas strut/piston by hand, it can only be compressed once added to the
frame
·Ensure the frame can move freely before adding the gas struts/pistons
·Check the frame is fully square, being offset can cause the frame to catch on the side rail
Page 12