DUSK Windsor User manual

Important
Assembly Tip
Before you begin, it's best to identify all of the parts and fittings to build your ottoman bed frame.
We advise laying these out on the floor to check you have everything, and to familiarise yourself
with all of the parts and fittings before building.
Top Tip
We recommend that you build your new ottoman bed frame in the room you'd like it to be
located. This will help prevent any risk of damage to the frame whilst moving it.
Safety and Care
It's important to ensure children and animals are kept away from the assembly area, as there
are small components used in this bed frame which could present a choking hazard. All
plastic and wrapping materials should also be kept away from children and animals to prevent
any risk of suffocation.
Help and Support
Please contact our customer service team on 0113 519 0311 if you have any questions or issues
with your purchase.
Recycling
Please ensure that packaging is disposed of in a safe and environmentally friendly way, and
recycle where possible. Please keep your assembly instructions safe to refer back to in the
future.
Page 2

Parts Check List
No.
Parts List
Qty
Box No
No.
Parts List
Qty
Box No
1
Headboard
1pc
Box 1
9
Plastic Corner Bracket
4pcs
Box 1
2
Footboard
1pc
Box 1
10
Angle Corner Bracket
4pcs
Box 1
3
Side Rail with Lift Mechanism - LH
1pc
Box 2
11
Holding Block
1pcs
Box 1
4
Side Rail with Lift Mechanism - RH
1pc
Box 2
12
Strap
1pc
Box 1
5
Adjustable leg
4pcs
Box 1
13
Slat
26/30pcs
Box 1
6
Front/Rear Ottoman Metal Frame
2pcs
Box 1
14
Side Slat Cap Double/king
26/30pcs+1 extra
Box 1
7
Horizontal Support Rail
3pcs
Box 1
15
Centre Slat Cap Double/ king
13/15pcs+1 extra
Box 1
8
Central Support Rail
1pcs
Box 2
16
Fabric Base
1pc
Box 1
Pre-assembled Parts Check List
17
Side Support Rail
2pcs
Box 2
18
Side Metal Rail
2pcs
Box 2
19
Lift Mechanism - LH
1pc
Box 2
20
Lift Mechanism - RH
1pc
Box 2
21
Angle Iron Bracket -LH
2pcs
Box 2
22
Angle Iron Bracket -RH
2pcs
Box 2
23
Piston
2pcs
Box 2
3OHDVHFKHFN\RXKDYHDOOWKHILWWLQJVOLVWHGEHORZZLWK\RXUSURGXFW%R[
Pre-assembled Fittings
M8 Flat Washer 12pcs
M8 60mm Bolt 6pcs
M6 15mm Bolt 4pcs
NB there are additional spare Fittings included within the Fitting pack
Page 5
E
M8 Nut 2pcs
G
K
M8 25mm Bolt 12pcs
L
M

Step 2: Attaching the Bolts to the Headboard & Footboard
NB:
Before tightening the bolts, please ensure the bed frame is square

Step 3:
Attaching the Left & Right Side Rails to the Headboard & Footboard
NB：Before tighteing the bolts, please ensure the bed frame is square Page 7
WRONG CORRECT

6WHS4: $WWDFKLQJWKH6LGH5DLOVWRWKH+HDGERDUG
)RRWERDUGXVLQJ the Angle Corner Brackets
2 pcs
8 pcs

6WHS5:6HFXULQJWKHOHIW
5LJKW6LGH5DLOVWRWKH/LIWLQJ0HFKDQLVP
2 pcs
Leave the
ottoman bed frame in an elevated position.
Page 8
Step 6: Attaching the Fabric Base & Legs
J
E

Fit the
fabric
base
along the
velcro on
the base
of bed
frame.
Make
sure the
side of
the fabric
base with
2 holes is
attached to the footboard and attach the legs
through the 2 holes to the footboard.
5
1

Step 7: Attaching the Rear Ottoman Metal Frame to the Side Rails
Page 9

Step 11: Attaching the Slats & Strap to the Ottoman Metal Frame
Side Slat Caps Double/King 26/30 pcs
Centre Slat Caps Double/King 13/15
pcs
Push down firmly on the Slat Caps into the pre-drilled
holes on the Ottoman Metal
Frame. It is recommended to push the Centre Slat
Caps into position before pushing down on the Side
Slat Caps.
Attaching the Slats & Strap to the Ottoman Metal
Frame – this is much easier to do with the frame
closed. The frame needs to be closed without the
mattress, and may need more force than expected –
refer to the last page for gas strut trouble shooting.
1
5
1
4

Care and Maintenance
Here are some good tips to keep your new ottoman bed frame in tip-top condition.
Cleaning
To clean your new ottoman bed frame, we advise using a damp cloth if the fabric is dusty or a low
suction vacuum. Do not use abrasive chemicals or bleach as this may damage the product.
Checking and Moving
Periodically, we recommend you check that the screws and fixtures haven't become loose over time.
To move your bed frame, we recommend lifting it where possible, as dragging or pushing it could
cause damage to the legs or flooring.
Fabric
Please note, depending on the Iighting, positioning and surroundings of your room, the shade of
the fabric will appear differently. Over a period of time, the fabric may also lighten or fade
slightly due to light exposure.
Page 12

Gas strut/piston best use:
·Use caution when operating - always use two hands.
·Only attempt to close the ottoman frame, once the mattress has been placed on the frame.
·The thicker side of the cylinder should be above the thinner side - this will increase longevity ofthe part.
·Only attempt to close the frame with two hands from the footboard side, slowly increasing the pressure
until the frame starts moving downwards.
·Closing the frame for the first time may be difficult, as the cylinder needs cycling and lubricating. After
closing for the first time, open and close a further 5 times.
·If the frame is stuck open and unable to be closed, we recommend getting assistance from a second
person, both applying equal pressure from each side of the footboard until the frame closes, this may
require more force than expected. Stop applying pressure if the metal frame begins to warp – contact
customer services at this point.
Top tips:
·Do not attempt to close the gas strut/piston by hand, it can only be compressed once added to the frame
·Ensure the frame can move freely before adding the gas struts/pistons
·Check the frame is fully square, being offset can cause the frame to catch on the side rail
Page 13

Tp
efore you begin, it's best to identify all of the parts and fittings to build your ottoman bed
frame. We advise laying these out on the floor to check you have everything, and to familiarise
yourself with all of the parts and fittings before building.
T
We recommend that you build your new ottoman bed frame in the room you'd like it to be
located. This will help prevent any risk of damage to the frame whilst moving it.
a C
It's important to ensure children and animals are kept away from the assembly area, as there
are small components used in this bed frame which could present a choking hazard. All
plastic and wrapping materials should also be kept away from children and animals to prevent
any risk of suffocation.
S
Please contact our customer service team on 0113 519 0311 if you have any questions or issues
with your purchase.
Please ensure that packaging is disposed of in a safe and environmentally friendly way, and
recycle where possible. Please keep your assembly instructions safe to refer back to in the
future.
Page 2