DXV D35703312.100 User manual

- 1 -
INSTALLATION INSTRUCTIONS
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2017
SAVE FOR FUTURE USE
RECOMMENDED TOOLS AND MATERIALS
Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing,
supply stores. It is essential that the tools and materials be on hand before work is begun.
M965869 (11/17)
12"Grab Bar – Model D35703312.100
18"Grab Bar – Model D35703318.100
24"Grab Bar – Model D35703324.100
Grab Bar
ROUGHING-IN DIMENSIONS:
• For reference
Phillips Screwdriver
Drill
3mm (1/8")
Drill Bit Level
Flat Blade Screwdriver Hammer
In the United States:
DXV
One Centennial Avenue
Piscataway, New Jersey 08855
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.DXV.com
In Canada:
DXV
5900 Avebury Road
Mississauga, Ontario
L5R 3M3
Canada
Toll Free: 1-800-387-0369
Local: 905-306-1093
Fax: [phone]
www.DXV.ca
In Mexico:
DXV
Via Morelos 330
Col. Santa Clara Coatitla
Ecatepec, Estado de México 55540
Toll Free: 01-800-8391200
www.DXV.mx
Thank you for selecting DXV. To ensure that your
installation proceeds smoothly, please read these
instructions carefully before you begin.
3-7/16"
(88 mm)
Ø 2-1/8"
(54 mm)
11-5/8"
(295 mm)
3-5/8"
(93 mm)
Ø 2-1/4"
(57 mm)
17-1/8"
(450 mm)
3-5/8"
(93 mm)
Ø 2-1/4"
(57 mm)
23-5/8"
(600 mm)

- 2 - M965869 (11/17)
1INSTALL GRAB BAR
CARE INSTRUCTIONS:
• The GRAB BAR (1) works best when secured
to the wall studs or cross brace using WOOD
SCREWS. If mounting into the studs is not
possible, use appropriate wall fasteners
provided to secure the installation.
• Mark a vertical center line in the location you
wish to install the SLIDE BAR (1).
NOTE: The height from the finished floor is
optional. See rough-in drawing for suggested
dimensions.
• Determine desired height from the nished oor
to the lower support and mark a horizontal center
line. Slide the two WALL ESCUTCHEONS (5)
away from the MOUNTING FLANGES (3).
Position the GRAB BAR (1) as shown in Fig. A
and mark the location of the six mounting holes
to be drilled. Fig. A. Using a #10 masonry drill,
drill six mounting holes 1-1/4" max. deep. Fig. B.
• Install the six ANCHORS (2) provided into the
mounting holes. Use a hammer to lightly tap
ANCHORS (2) into place. Make sure they are
installed ush against the nished wall. Fig. B.
• Align and place the GRAB BAR MOUNTING
FLANGES (3) over the installed ANCHORS (2).
Secure the GRAB BAR (1) to the wall with the
SCREWS (4) provided. Fig. B.
• Push WALL ESCUTCHEONS (5) against nished
wall. Rotate WALL ESCUTCHEONS (5) clockwise
to lock into position. Fig. C.
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH
WITH A COARSE SURFACE.
OPTIONAL TO FINISHED FLOOR
USUALLY BETWEEN
FINISHED
FLOOR
915mm
(36")
1525mm
(60")
TO
914mm
(36")
2
LEVEL
VERTICAL
CENTER LINE
DRILLED
MOUNTING
HOLES
C/L
1 1
3
4
5
5
Fig. A Fig. B
M964179-0070A
MOUNTING KIT
AVAILABLE FINISH
POLISHED CHROME 100