Dynamix DW-01PlusS User manual

DYNAMIX DW-01Plus/S
FXS Gateway
User’s Manual

List of Table II
Part I: Dynamix DW-01Plus/SOverview .............................................................................1
1.1 Overview........................................................................................................................2
1.2 Software Specifications .............................................................................................3
1.3 Hardware Specifications ............................................................................................4
Part II: Start-UP....................................................................................................................... 7
2.1 Software Installation Guide .......................................................................................8
2.1.1 Default Settings of Dynamix DW-01Plus/S..........................................................8
2.1.2 Additional Installation Requirements.....................................................................8
2.1.3 Essential Configuration via Web Management interface....................................9
2.1.3.1 Save Data and Reboot..................................................................................10
2.1.3.2 Setup Network ...............................................................................................12
2.1.3.3 Application mode-Proxy/Peer-to-Peer Mode...............................................15
2.1.4 Essential Configuration via Telnet Command Line interface............................18
2.1.4.1 Save Data and Reboot..................................................................................18
2.1.4.2 Setup Network ...............................................................................................18
2.1.4.3 Application mode-Proxy/Peer-to-Peer Mode...............................................20
2.1.5 Essential Configuration via Installation Wizard..................................................22
2.1 Special Housing Installation Guide........................................................................ 23
2.1.1 Horizontal Type.....................................................................................................23
2.1.1.1..........................................................................................................................23
2.1.1.2..........................................................................................................................23
2.1.1.3..........................................................................................................................23
2.1.2 Vertical Type..........................................................................................................24
2.1.2.1..........................................................................................................................24
2.1.2.2..........................................................................................................................24
2.1.2.3..........................................................................................................................24
Part III: Special Applications and Features..................................................................... 25
3.1 Behind IP-Sharing ..................................................................................................... 26
3.1.1 IP Sharing Configuration......................................................................................26
3.1.1.1 One Dynamix DW-01Plus/S behind Dynamix DW-01Plus/S.....................26
3.1.1.2 More than one Dynamix DW-01Plus/S behind the same IP Sharing
Device..........................................................................................................................29
3.2 NAT mode (PPPoE).................................................................................................... 31
3.3 Call Hold, Transfer and Forward............................................................................. 33
3.3.1 Call Hold –press [FLASH]...................................................................................33

List of Table III
3.3.2 Call Transfer –press [FLASH], then [transferring number] ..............................33
3.3.3 Call Forward:.........................................................................................................33
3.4 Upgrade Your Dynamix DW-01Plus/S .................................................................... 35
3.4.1 Upgrade via Web management interface...........................................................35
3.4.1.1 Before start.....................................................................................................35
3.4.1.2 Upgrade Version............................................................................................35
3.4.2 Upgrade via Telnet Command interface.............................................................37
3.5 Dynamix DW-01Plus/S PSTN Line Application.................................................... 39
3.5.1 PSTN Outgoing Call.............................................................................................39
3.5.1.1 Make PSTN call from TEL Phone set..........................................................39
3.5.1.2 PSTN Backup.................................................................................................39
3.5.2 PSTN Incoming Call.............................................................................................39
3.5.2.1 VoIP TEL is busy............................................................................................39
3.5.2.2 VoIP TEL is available.....................................................................................39
3.5.3 VoIP Outgoing Call ...............................................................................................39
3.5.4 VoIP Incoming Call...............................................................................................39
3.6 Hotline mode .............................................................................................................. 40
Part IV: Web Management Interface................................................................................. 41
4.1 Login and welcome screen...................................................................................... 42
4.2 Save and Reboot........................................................................................................ 43
4.3 Web Management Configuration............................................................................ 44
4.3.1 Network Interface..................................................................................................44
4.3.2 SIP Information Screen........................................................................................46
4.3.3 System Configuration...........................................................................................48
4.3.4 PPPoE Configuration Screen..............................................................................49
4.3.5 Voice Configuration Screen.................................................................................50
4.3.6 Phone Configuration Screen ...............................................................................51
4.3.7 Support Configuration Screen.............................................................................53
4.3.8 Phone Book Configuration...................................................................................54
4.3.9 Prefix Configuration Screen.................................................................................55
4.3.10 DSCP Configuration Screen..............................................................................56
4.3.10 Password Configuration Screen........................................................................58
4.3.11 ROM Configuration Screen................................................................................59
4.3.12 Flash Clean Screen............................................................................................60
4.3.13 Commit Configuration Data Screen..................................................................61
4.3.14 Reboot Dynamix DW-01Plus/S System screen...............................................62

List of Table IV
Part V: Telnet Command Interface.................................................................................... 63
5.1 Login ............................................................................................................................ 64
5.2 Save and Reboot........................................................................................................ 64
5.3 System Commands Overview ................................................................................. 65
5.3.1 [help]......................................................................................................................65
5.3.2 [quit] .......................................................................................................................66
5.3.3 [debug]...................................................................................................................66
5.3.4 [reboot]...................................................................................................................68
5.3.5 [commit].................................................................................................................68
5.3.6 [ifaddr]....................................................................................................................69
5.3.7 [time] ......................................................................................................................71
5.3.8 [ping]......................................................................................................................72
5.3.9 [pbook]...................................................................................................................72
5.3.10 [pppoe].................................................................................................................74
5.3.11 [flash]....................................................................................................................75
5.3.12 [sysconf] ..............................................................................................................77
5.3.13 [sip].......................................................................................................................79
5.3.14 [security]..............................................................................................................81
5.3.15 [voice]...................................................................................................................82
5.3.16 [support]...............................................................................................................84
5.3.17 [tos]......................................................................................................................86
5.3.18 [phone].................................................................................................................86
5.3.19 [bureau]................................................................................................................90
5.3.20 [rom].....................................................................................................................91
5.3.21 [passwd] ..............................................................................................................94
5.3.22 [prefix]..................................................................................................................95

Dynamix DW-01Plus/S Gateway User Manual
- 1 -
Part I:Dynamix DW-01Plus/S Gateway
Overview
This part introduces the software/hardware specifications and default settings of the
Dynamix DW-01Plus/S.

Dynamix DW-01Plus/S Gateway User Manual
- 2 -
1.1 Overview
The Dynamix DW-01Plus/S is a one-port telephone extension and three ports
SOHO Router to IP network gateway. It provides Data transfer by 10/100Mbps,
telephone services and T.38 fax over IP network with easily operation and configuration.
It is most suitable for SOHO and small-to-medium enterprise in Internet communication
environment.
The Dynamix DW-01Plus/S provides IP telephone number for end users with
FreeTalk voice service. User can make phone call via Internet now. No more long
distance and international telephony fee! It also connects three computers without
another IP sharing as showed as following diagram.
The Dynamix DW-01Plus/S provides two telephone numbers that one is IP
telephone number and the other is PSTN telephone number in one device for end users.
You can make phone call via Internet or PSTN in one telephone set now. No more long
distance and international telephony fee! Especially, User still can make phone call
when external power is failure.
The Dynamix DW-01Plus/S also can connect three computers with embedded IP
sharing and DHCP server function.

Dynamix DW-01Plus/S Gateway User Manual
- 3 -
1.2 Software Specifications
Dynamix DW-01Plus/S Gateway Features
Provide Voice over IP and Fax over IP features.
SIP RFC 3261 compliance
Built-in NAT/IP sharing function
Provided call features: Hold, forward and transfer
Automatic FAX detection (Support T.38 protocol)
Codec: G.711 a/ìlaw, G.723.1, G.729A
PPPoE connection
VAD (Voice Activity Detection), CNG (Comfort Noise Generate)
G.168/165 echo cancellation
FSK and DTMF Caller ID
Provide both IP telephone number and PSTN telephone number in one device
for end users
PSTN backup: user still can make phone call when external power is failure
Audio feature
Codec: G.711 a/ìlaw, G.723.1 (6.3kbps), G.729A
VAD (Voice Activity Detection)
CNG (Comfort Noise Generation)
G.168/165-compliant adaptive echo cancellation
Dynamic Jitter Buffer
Bad Frame Interpolation
Voice/DTMF Gain Settings
System Monitoring
System status (WAN, LAN, TEL, Status, Power)
Remote Firmware Upgrade
You can use FTP/TFTP to perform firmware upgrade for the Dynamix
DW-01Plus/S Gateway from a remote location.
Security
Password protection for system management
Built-in NAT function.
Certification
CE, FCC

Dynamix DW-01Plus/S Gateway User Manual
- 4 -
1.3 Hardware Specifications
Chassis
190mm(W) x 110mm(D) x 51.5mm(H)
Weight (unit): 0.3 kg
Interface
Four 10/100 Base-T Ethernet RJ-45 ports (Auto LAN MDI/MDIX).
Input AC 100V-240V, Output DC 12V.
One/Two RJ11 Telephone Port.
Special Housing
The plastic housing can be adjustable by manual (Vertical type or Horizontal
type)
Environment
Operational Humidity: 10 to 90 % (Non-condensing)
Operational Temperature: 0 to +40 C
Storage Humidity: 10 to 90 % (Non-condensing)
Storage Temperature: -10 to +50 C
Front Panel
The LEDs on the front panel indicate the operational status of the Gateway.
Power (Green):
(1) Light on: Dynamix DW-01Plus/S is connected with power adapter
correctly and power on.
(2) Light off: Dynamix DW-01Plus/S is not connected with power adapter
correctly or not power on.
Status (Green):
(1) Light on: Dynamix DW-01Plus/S is under Proxy mode and successfully
register to Proxy.
(2) Light off: Under Peer-to-Peer mode.

Dynamix DW-01Plus/S Gateway User Manual
- 5 -
(3) Light Blanking: Dynamix DW-01Plus/S is under Proxy mode and not
successfully register to Proxy.
TEL (Orange):
(1) Light Blinking: Dynamix DW-01Plus/S IP side has incoming call.
(2) Light On: Dynamix DW-01Plus/S IP side is in communication.
(3) Light Off: IP Line of Dynamix DW-01Plus/S is in standby mode.
WAN/LAN (Green):
(1) Light on: Ethernet port successfully connected with network.
(2) Light Blanking: Ethernet port is transmitting or receiving data.
PSTN (Orange):
(1) Light Blinking: Dynamix DW-01Plus/S IP side has incoming call.
(2) Light On: Dynamix DW-01Plus/S PSTN side is in communication.
(3) Light Off: PSTN Line of Dynamix DW-01Plus/S is in standby mode.
Back Panel
Ethernet Port:
Ethernet port is for connecting VoIP Gateway to network, transmit rate
supports 10/100 Base-T.
Ethernet connector（LAN/WAN）

Dynamix DW-01Plus/S Gateway User Manual
- 6 -
TEL Port:
RJ-11 connector, Dynamix DW-01Plus/S interface to connect analog phone
sets or trunk port of PABX.
PSTN Port:
RJ-11 connector, Dynamix DW-01Plus/S interface to CO PSTN line or
extension port of PABX.
DC 12V Port:
DC 12V Power supply.

Dynamix DW-01Plus/S Gateway User Manual
- 7 -
:
Part II: Start-UP
This part explains how to configure essential and basic items before user can run
Dynamix DW-01Plus/S gateway.

Dynamix DW-01Plus/S Gateway User Manual
- 8 -
2.1 Software Installation Guide
This guide covers all essential configurations under different application, user can follow
steps below to configure basic items to run Dynamix DW-01Plus/S gateway.
2.1.1 Default Settings of Dynamix DW-01Plus/S gateway
WAN IP Parameters
(1) WAN
IPAddress = 10.1.1.3
Subnet mask = 255.0.0.0
Default gateway = 10.1.1.254
(2) LAN
IPAddress = 192.168.123.123
Subnet mask = 255.255.255.0
Telnet and Web Login Password
Login User Name= root
Password = “Null”(default)
2.1.2 Additional Installation Requirements
In addition to the contents of your package, there are other hardware and software
requirements you need before you can install and use your Dynamix DW-01Plus/S
Gateway. These requirements include:
1. A computer with an Ethernet NIC (Network Interface Card) installed.
2. Use Internet Explorer 5.5 or later / Netscape Navigator 6 or later versions.
3. Analog telephone set.
4. Software tools: SIP Proxy Server (optional)
5. Installation Wizard (optional): This is a configuration tool for users can easy
access products and configuring IP address. Please contact with your
retailer for more information.
Please follow steps below to access Dynamix DW-01Plus/S configuration interface:
Step 1.Connect WAN Port of Dynamix DW-01Plus/S Gateway to public
network
Connect the WAN port (silver) on the Dynamix DW-01Plus/S Gateway to

Dynamix DW-01Plus/S Gateway User Manual
- 9 -
the Ethernet port of your network (e.g. Cable Modem, ADSL Modem)
using the standard CAT-5 straight Ethernet cable.
Step 2. Connect your PC to the LAN port of Dynamix DW-01Plus/S
Connect your PC to the LAN port of Dynamix DW-01Plus/S with standard
CAT-5 straight Ethernet cable.
Step 3. Set your PC as DHCP mode
Please go to the network setting of your PC and set it as DHCP mode, let
your PC can automatically search for DHCP server and get one valid IP
address. Dynamix DW-01Plus/S has embedded DHCP server (default is
enabled) so that your PC will get one IP address from Dynamix
DW-01Plus/S DHCP server.
Step 4.Open your browser and input IP address 192.168.123.123
Once your PC has got an IP from Dynamix DW-01Plus/S, you may
connect Dynamix DW-01Plus/S via WEB browser to do more
configurations. The default LAN IP address of Dynamix DW-01Plus/S is
“192.168.123.123”;please input this IP address on web browser to
connect with web management interface. Please refer to Part III Web
management for more information.
Step 5.Advanced Setting via Telnet (Optional)
If user wants to do more advanced and complete settings that cannot be
found via web management interface, please Telnet to the Dynamix
DW-01Plus/S to do more detail configurations.
Step 6.Connect other PC with LAN Ports (Optional)
If you have more than one PC, you can connect them with LAN Ports
(black) on the Dynamix DW-01Plus/S. Please set these PCs as DHCP
mode so that they can automatically get IP from DHCP server. DHCP
server of Dynamix DW-01Plus/S can assign 253 IP most.
Caution:
To prevent damage to the Dynamix DW-01Plus/S Gateway, please make
sure you have connected with the correct power adapter.
2.1.3 Essential Configuration via Web Management interface
This section describes how to setup Dynamix DW-01Plus/S via Web management
interface. Please follow procedures below to configure essential items before you use
Dynamix DW-01Plus/S gateway.

Dynamix DW-01Plus/S Gateway User Manual
- 10 -
2.1.3.1 Save Data and Reboot
After any configuration has been made, user has to save all data and reboot system to
make configurations take effect.
Step 1. Click [Commit Data] on the navigation panel. In the Commit Configuration
Data screen, click the [Commit] button. In the Commit Configuration Data screen
will Display [Commit to Flash OK!], when Dynamix DW-01Plus/S finished
committing data.
Step 2. Click [Reboot System] on the navigation panel. In the Dynamix DW-01Plus/S
Gateway screen, click the [Reboot] button. It will take around 40 seconds to reboot.

Dynamix DW-01Plus/S Gateway User Manual
- 11 -
Step 3. Close the current browser windows and launch your web browser again.

Dynamix DW-01Plus/S Gateway User Manual
- 12 -
2.1.3.2 Setup Network
(1) Fixed IP
To configure the VoIP Gateway IP address, please click [Network Interface] on the
navigation panel. In the Network Interface screen, type a new IP address, subnet
mask and the default routing gateway (e.g. IP Address: 192.168.0.188, Subnet
mask: 255.255.255.0, Default routing gateway: 192.168.0.1) and click the OK
button.

Dynamix DW-01Plus/S Gateway User Manual
- 13 -
(2) DHCP
Click [Network Interface] on the navigation panel. In the Network Interface screen,
enable the DHCP function if you are using the cable modem or DHCP server and
click the [OK] button.

Dynamix DW-01Plus/S Gateway User Manual
- 14 -
(3) PPPoE
Click [PPPoE Configuration] in the navigation panel and open the [PPPoE
Configuration] Screen.
-Device: Set PPPoe function to be On or Off.
-User Name: Set PPPoE authentication User Name.
-Password: Set PPPoE authentication password.
-Reboot After Remote Host Disconnection: Enable/Disable auto reboot after
PPPoE disconnection
If user enables this function, after PPPoE being disconnected, Dynamix
DW-01Plus/S will automatically reboot to re-connect, and after rebooting, if
Dynamix DW-01Plus/S still can’t get contact with server, Dynamix DW-01Plus/S
will keep trying to connect. After re-connected, Dynamix DW-01Plus/S will also
restart system. On the other hand, if user disables this function, Dynamix
DW-01Plus/S won’t reboot and keep trying to connect.
-Other items: for reference only, cannot allow to be configured.

Dynamix DW-01Plus/S Gateway User Manual
- 15 -
2.1.3.3 Application mode-Proxy/Peer-to-Peer Mode
After setting IP address, user must assign Dynamix DW-01Plus/S to work under Proxy
mode or Peer-to-Peer mode. If there is no Gatekeeper, please set your Dynamix
DW-01Plus/S as Peer-to-Peer Mode.
2.1.3.3.1 Proxy mode
Proxy mode means that there will be an intermediate Proxy Server between Dynamix
DW-01Plus/S Gateway and the remote entity. While operating at this mode, Dynamix
DW-01plus/S Gateway will first register to the Proxy Server located at the ISP side. For
the following operation, it sends the INVITE message to the Proxy Server once you
initiate a session. Then the Proxy server will forward the INVITE message to the right
place.And the Response message from the remote entity will be forwarded back to you
via Proxy server.
Step 1. Configure the Dynamix DW-01Plus/S Gateway SIP Configuration. Click SIP
Information on the navigation panel. In the SIP Information screen, select Proxy
routed Mode function.
Step 2. Set the SIP information from your service provider: Proxy IP Address, Line1
Number, Line1 Account, Line1 Password, and click the OK button.
Note:
1. Please contact with your Proxy vendor to obtain user account information.
2. If no need to enter password, user also has to set security information, please set
“name”the same with line number.
3. Dynamix DW-01Plus/S Gateway uses “line number”to regist
er to proxy server,
the “name”is only for authentication.

Dynamix DW-01Plus/S Gateway User Manual
- 16 -
2.1.3.3.2 Peer-to-Peer Mode
Peer-to-Peer Mode allows users to call other VoIP devices without the proxy server.
When in Peer-To-Peer mode, Dynamix DW-01Plus/S Gateway use Phone Book, which
will dial predefined phone number, and press “#”(optional, to accelerate the dial) as end
of dial.
To configure Peer-To-Peer Mode in Dynamix DW-01Plus/S Gateway, follow the steps
below:
Step 1. Configure the Dynamix DW-01Plus/S Gateway SIP information. Click [SIP
information] on the navigation panel. In the SIP information screen, select
Peer-to-Peer Mode function, set line number, line account and click the [OK] button.
Line account must be the same with Line number.