Eachine 1S Cinefun 75mm 1080P/ 4K Cinewhoop User manual

M1
M2
M3 M4
+5V
TX1
IR1
GND
RX1
BIND
RX2
TX2
LED_STRIP
BOOT
GND
BAT+
M1
M2
M3
M4
+5V
TX1
BOOT
GND BAT+
IR1
GND
RX1
BIND
RX2
TX2
LED_STRIP
Arm/Disarm the Motor
2. Set Arm/Disarm switch for your Flysky Radio: Move to the Aux.channels interface, Set “SWA”
or “SWB” or “SWC” switch etc. for Ch5 to ARM/DISARM the motor.
1. The Default Arm/Disarm switch for is AUX1(Channel 5),and you can also customize it with
Betaflight Configurator.
Cinefun
3 The default channel map for Cinefun Flysky version is AETR1234, please make sure your
transmitter is matched , otherwise it will can't be armed. Toggle the AUX1 Switch ,the Green LED
.
on the flight controller will getting to be solid, this indicates the Cinefun was armed . And also you
can found “Armed” displayed on your FPV Goggles or the FPV Monitor. Please make sure keep the
Cinefun level before arming .Be careful and enjoy your flight now!
Receiver configuration
Please set Receiver mode to be SPI RX Support from the Configuration tab of the Betaflight
Configurator, then select A7105_Flysky_2A Provider for AFHDS-2A Protocol Radio transmitter
or Select A7105_Flysky Provider for AFHDS Protocol Radio transmitter, don't enable Serial RX
since the Crazybee F4 lite Flight controller is integrated SPI BUS Receiver
Binding procedure
1. Betaflight 3.5.7 version(Original firmware out of box) binding procedure: Press and hold the
bind button then powering the Cinefun , the Red LED at the bottom of the flight controller
will blinking fast , this indicate the receiver is in bind mode .
Betaflight firmware later than 4.0.1(include)binding procedure: Powering the Cinefun first,
then Press the bind button for 1 second ,the red Led at the bottom of the flight controller will
blinking fast, this indicate the receiver is in bind mode.
2. Another simple way to bind with the Flysky transmitter is : plug the usb and move to the CLI
Command , then type bind code "bind_rx_spi"(for betaflight 4.0.1~4.0.6) or type bind code
"bind_rx"(for betaflight 4.1.X), the receiver will getting into bind mode, and then make your
Flysky transmitter to bind mode, the LED at the bottom of the flight controller will getting to
be solid if bind successfully. (Betaflight 3.5.7 firmware not support these bind code)
Eachine Cinefun 75MM 1080P/4K FPV Cinewhoop Flysky version
Flight controller connection diagram
Specifications
Brand Name: Eachine
Item Name: 1S Cinefun 75mm 1080P/ 4K Cinewhoop
Wheelbase: 75mm
Size: 97mm*97mm*51mm
Weight: 39g(without battery)
Weight:54.5g(with Original 1s 650mah Lipo battery )
The lightest 4K Cinewhoop in the World
Powerful and smoothly
Caddx Loris 4K Camera & DVR ready
Runcam Split3-lite 1080P Camera & DVR ready
Betaflight OSD support ,easy to get RSSI, Voltage ,current from your goggles
Camera Angle adjustable
VTX power switchable 25mw~200mw
Features
Package includes
Qty
1
1
4
1
1
1
4
1
1
75mm Frame
Option1: CrazybeeX FR V2.2 built-in SPI Frsky receiver
Option2: CrazybeeX FS V2.2 built-in SPI Flysky receiver
Option3: CrazybeeX PNP V2.2 with external TBS Crossfire Nano RX
NC1102 KV19000 motors
HQPROP 1.6x1.6x4 propeller(4cw+4ccw)
Option1:Runcam Split3-lite
Option2:Caddx Loris
Built-in 5.8G 40ch 25mw-200mw VTX
1s 650mah Lipo battery
Propeller disassemble tool
Screwdriver
Item Name
GND
+5V Video out_
Video in_
Camera
+5V out
GND
GND
+5V
IR1
RX1
TX1
RX2
TX2
BIND
BOOT
LED_STRIP
BUZ-
+5V
BAT+
GND
Disconnect the soldering
pad and then you can use
external vtx
Toggle the AUX1 Switch, the Green LED on
the Flight controller will getting to be solid
Toggle the AUX1 Switch, the Green LED on
the Flight controller will getting to be solid
4K version
1080P version1080P version

Firmware update
Mixer type and ESC/motor protocol
Default PID setting
3.Open the Device Manager of your computer, find the Ports, please make sure the Com port
Serial Number is under 255, otherwise it will can't connect to the BLHELISUITE. You can change
the port serial number like the bellowing step :
4.Open the BLHELISUITE, Select SILABS BLHeli Bootloader (Cleanflight) from the third tab on
the top side. Then Select the right Serial com port and Click connect. You can also Flash the
new release BLHeli_s firmware via the BLHEILISUITE, the firmware Target is “S-H-50”
Flight controller firmware update
1.Install latest STM32 Virtual COM Port Driver
2.Install STM BOOTLOAD Driver (STM Device in DFU MODE)
3.Open Betaflight configurator and choose firmware target “CRAZYBEEF4FS(LEGACY)”,then
select the firmware version.
4.There are 2 ways to get in DFU Mode: 1). solder the boot pad and then plug USB to computer 2).
loading betaflight firmware and hit “flash”, then it will getting into DFU Mode automatically.
5.Open Zadig tools to replace the drivers from STM32 Bootloader to WINUSB Driver.
6.Reconnect the flight controller to the computer after replace driver done , and open
Betaflight Configurator, loading firmware and flash.
http://www.st.com/web/en/catalog/tools/PF257938
VTX Bands and Channels setup
Frequency and channel frequency table:
CH
FR
Band1 A()
Band2 B()
Band3 E()
Band4 F()
Band5 R()
C1H
5865M
5733M
5705M
5740M
5658M
C2H
5845M
5752M
5685M
5760M
5695M
C3H
5825M
5771M
5665M
5780M
5732M
C4H
5805M
5790M
5665M
5800M
5769M
C5H
5785M
5809M
5885M
5820M
5806M
C6H
5765M
5828M
5905M
5840M
5843M
C7H
5745M
5847M
5905M
5860M
5880M
C8H
5725M
5866M
5905M
5880M
5917M
:
.,:
_=
_=
.(++)
,,
There are 2 ways to switch the vtx channels
1 If we need to use Channel 5705 then we should Go to Betaflight CLI type the command
Set VTX band 3
Set VTX channel 1
save
2 Disarm the Cinefun and then move the stick of the transmitter THR MID YAW LEFT PITCH UP
to enter OSD Menu Enter to Features then enter to VTX SA to set VTX Band and channel
1.Download New release Blhelisuite from:
2.Plug the usb and connect the flight controller to computer
https://www.mediafire.com/folder/dx6kfaasyo24l/BLHeliSuite
ESC Check and Flash firmware
Set one channel of your radio transmitter to activate the Flip over function in
.the Mode tab of Betaflight configurator
The default Switch for Activate “Flip" is AUX4(Channel8)
Crashed Disarm
The Quad
Activate
Flip over
Arm
The Quad
Move stick
to flip the Quad
“Flip over after crash” procedure
Betaflight 3.5.7 Default PID settings:
Note:
"ESC Check and flash firmware" and "Flight controller firmware update" procedure are not
necessary . The procedure at the right side is just a tutorial to show how to do it. We already
pre-install firmware and pre-configure the ESC and the flight controller.
Eachine Cinefun 75MM 1080P/4K FPV Cinewhoop Flysky version
Firmware target
Click check to see the
details of the 4in1 ESC
Flash firmware