Eachine TYRO79 User manual

TYRO79
QUICK START GUIDE (DIY)

Package included:
1 x 140mm racing frame kit
2 x 1607 2800KV brushless motor CW
2 x 1607 2800KV brushless motor CCW
1 x 4 IN 1 20A BLHeli_S ESC
1 x Customized F4 flight controller
1 x 700TVL CMOS camera
1 x 5.8G 40CH 0mw/25mw/200mw switchable VTX
2 x 3030 4-blade propeller CW
2 x 3030 4-blade propeller CCW
TY RO 79 QUICK START GUIDE
-2-
Antenna
F4 flight controller
20A 4in1 Brushless ESC
Switchable VTX
700TVL CMOS
Micro camera
1607 2800kv
brushless motor
3030 4-blade propeller

-3-
Contents
1.0 Frame kit----------------------------------------04
4.0 Flight controller---------------------------------05
2.0 ----------------------------------------04
Motor-----
5.0 Switchable VTX---------------------------------06-09
3.0 Esc------------------------------------------------05
6.0 Camera-----------------------------------------------09
7.0 Screws---------------------------------------------10
9.0 Motor Unlock/Lock------------------------------12
8.0 Adjusting parameter -----------------------------10-11
10.0 Traversing flight---------------------------------12
TY RO 79 QUICK START GUIDE

1.0 Frame kit
2.0 Motor
Wheel base: 140mm
Bottom plate thickness: 3mm
Side plate thickness: 1mm
Frame kit material: 3K carbon fiber & 6065 aluminium
-4-
KV: 2800KV
Lipo cell: 2-4S
Weight: 17.8g (includes wires)
Output shaft length: 14mm
Maximum pull: signal 630g
(4S 3030 4-blade propeller)
Maximum power: 350W
Configu-ration: 9N/12P
Mounting holes distance: 12*12mm
Mounting holes: φM2
Bearing: NSK
N52 Strong NdFeB Magnet
Recommend propeller: 3 inch
TY RO 79 QUICK START GUIDE

3.0 ESC
Continuous current: 20A
Peak current: 25A (10S)
BEC output: no
Input voltage: 2-4S
Main control chip: 48mhz EFM8BB2
Firmware upgrade: Supports Dshot600/BLHeli_S/Oneshot125
MOS: 3*3
MOS type: vs3610ae 30v64a
-5-
4.0 Flight controller
Main control chip: STM32F411
Sensor: ICM20602 6-axis
Integrated OSD
PPM/DSM/IBUS/UAR share: UART1-RX
Mounting holes distance: 20*20mm
Weight: 24g
PID circulation rate and refresh rate can up to 32kHz
Supports Betaflight/cleanflight/inav firmware
TY RO 79 QUICK START GUIDE

-6-
5.0 Switchable VTX
Supports TBS SmartAudio
Transmitting power: 0mW/25mW/100mW/200mW switchable
Channel: 40CH
Full video format: NTSC/PAL
Input voltage: 7V~24V
Power dissipation: +12V/600MW
Size: 25×20×6mm
Weight: ≤3.2g (except antenna)
There are two ways to control the frequency and power
of the launches:
<1>
Enter the release: FEATURES->VTX SA can enter the following
interface.
uses remote control to visualize control, as shown in Figure
1.1
Figure 1.1
The second row is the status bar, respectively.
F:freestyle modeF5: is now in frequency band F,
fifth frequency point.
5820: now has a frequency of 5820.
500: now has a transmit power of 500MW
Third lines
BAND: indicates frequency band, and BAND can be
modified by remote control.A (BOSCAM A) B (BOSCAM B)
E (BOSCAM E) F (FATSHARK) F (E)
Fourth lines
CHAN: represents frequency points, and the 1---8 can be
modified by remote control.
Fifth lines
(FREQ): indicate the
corresponding frequency now, changing with the band and
Chan above.
Sixth lines
POWER: indicates the transmission
power and can be adjusted.
TY RO 79 QUICK START GUIDE

5.0 Switchable VTX
Seventh lines
SET: Enter and select YES to confirm your BADN, CHAN, POWER
settings and take effect immediately., as shown in Figure 1.2
below
Figure 1.2
Figure 1.3
-7-
Eighth lines
The CONFIG: function is set in, as shown in Figure 1.3 below.
OP MODEL: mode adjustment, with free mode and race mode,
needs reboot to take effect.
FSEL MODE: regulates frequency setting mode, CHAN and
user, user mode is temporarily invalid.
PIT FMODE:PITMODE mode, with PIR and POR mode.
TY RO 79 QUICK START GUIDE

5.0 Switchable VTX
-8-
In the POR mode, POR FREQ: can enter into any frequency
between 5300-5900, as shown in Figure 1.4.
Figure 1.4
STATX: status information
XMM-VTX is operated by a button with three LED lights (red
light CH1-8; blue light BAND1-5; green light power 1-3 <25-
100-200 mW>)and TBS Smart Audio remote control operation.
Keyboard operation: Long press 3S (three LED indicators are
all on) to open and enter CH switching operation, and the red
light will flash, flashing once represents the currentCH1 (2-8
times for CH2-CH8 respectively). At this time, a short press of
the key CH plus 1 will flash the corresponding number of times.
CH1-8 cycle. Press the button 3S (three LED lights are all on)
to open and enter the BANDswitching operation, and the blue
light will flash. The flash once represents the current BAND1
(2-5 times for BAND2-BAND5 respectively). At this time, press
the button BAND plus 1, and the blue light will flash correspondingly.
BAND1-5 cycle. Press the button 3S (three LED lights are all on)
again to open the power switching operation, and the green light
will flash, one time represents the current power of the first grade
(2-3 times for the green light flashing respectively), at this time,
press the button power to add one gear, and the green light will
flash the corresponding number of times. Power stall 1-3 cycle.
Press the button 3S again (3 LED lights are all bright) to release
the above settings again. Note that the previous settings will not
be saved if the power is off before saving. For example, if CH is
only set, it is also necessary to press 3S three times longer to
save the settings.Long press button 8S (green light) quit PIT mode.
<2>
TY RO 79 QUICK START GUIDE

Note: In the remote control, the power of 25 corresponds to
the actual 25 mW, 200 corresponds to the actual 100 mW, and
500/800 corresponds to the actual 200 mW.
5.0 Switchable VTX
6.0 Camera
Case size: 19mm*19mm
Weight: 9.5g
Total pixels: PAL: 1020H×596V (0.61MP);
NTSC: 1020H×508V (0.52MP)
Effective pixels: PAL: 976H×582V (0.57MP);
NTSC: 976H×494V (0.48MP)
Signal system: PAL/NTSC switchable
Resolution ratio(horizontal center): 700TVL
Video output: 1.0Vp-p/75Ω
Automatic gain control: 0.25/0.50/0.75/1.00, up to 55dB
White balance: off
Exposure mode: electron exposure
Electronic shutter: 1/50(1/60) - 1/100000 S
Gamma correction: 0.45/1.0
Synchronization method: inter-sync
Camera lens: standard 2.1mm
Lens operating voltage: DC 5-12V
Working current: 70mA (low power consumption)
Working temperature: -20℃~ - 60℃
Humidity: 0%~98%
-9-
TY RO 79 QUICK START GUIDE

7.0 Screws
8.0 Adjusting parameter
-10-
TY RO 79 QUICK START GUIDE

8.0 Adjusting parameter
-11-
TY RO 79 QUICK START GUIDE

9.0 Motor Unlock/lock
Put the throttle rocker at the lowest point, move the rudder rocker
to the right and keep it for more than 2 seconds. The blue state
indicator is always on, that is unlock the motor.
Put the throttle rocker at the lowest point, move the rudder rocker to
the leftmost side, and the red state indicator is always turned on to
lock the motor. At this time, pushing the throttle rocker motor upward
will not rotate.
-12-
Motor Unlock
Motor lock
10.0 Traversing flight
1).Flying is more suitable for experienced pilots.
2).During the flight, please keep the flight within the video
receiving range (the actual range depends on the flight
environment and weather conditions).
3).During flight, please avoid crowd, animals and
High voltage wires and other obstacles
TY RO 79 QUICK START GUIDE