Eachine US65 User manual

BAT+
3.5V-8.7V
GND BUZ-
+5V
M1
M2
M3
M4
+5V
TX2
RX2
LED_STRIP
BOOT
GND
TX1
RX1
IR1
1. Connect CH1(TX) of the XF Nano receiver to RX1 pad of the CrazybeeX , Connect CH2(RX) of the
XF Nano receiver to TX1 pad of the CrazybeeX. Enable Serial RX for Uart1 and Smart audio for
UART2
2. Choose the receiver mode to Serial-Based receiver and the Serial Receiver Provider is CRSF.
Enable telemetry in the Betaflight configurator and set AUX8 for RSSI
Receiver configuration
Arm/Disarm the Motor Use frsky x9d as an example
1. The Default Arm/Disarm switch for Us65 PRO/DE65 PRO is AUX1(Channel 5),and you can also
customize it with Betaflight Configurator.
3.The default channel map for US65 PRO/DE65 PRO Crossfire version is TAER1234, please make
sure your transmitter is matched, otherwise it will can't be armed. Toggle the AUX1 Switch ,the Green
LED on the flight controller will getting to be solid, this indicates the motor was armed . And also you
can found “Armed” displayed on your FPV Goggles or the FPV Monitor. Please make sure keep the
US65 PRO/DE65 PRO level before arming .Be careful and enjoy your flight now !
2.Turn on the transmitter radio which with TBS Micro TX module(Use Frsky x9d as a example) and
move to the MIXER interface, Set “SA” or “SB” switch etc. for Ch5 to ARM/DISARM the motor.
Some TBS TX and RX setting screen shot
TBS Micro TX configuration
TBS CRSF NANO Bind and Setup video https://www.youtube.com/watch?v=ioDzyV2vGb0
Binding the transmitter and receiver is super simple.
1. Just power up the TBS CROSSFIRE transmitter
2. On the standard transmitter, enter the configuration menu by pressing and holding the
joystick for 3 seconds, select “General” and “Binding” - a message “Binding” will start
blinking, waiting for the receiver. On the micro transmitter, a short press on the button will
initiate binding mode.
3. Now, power up the receiver (without pressing the Bind button!), if your receiver has not been
previously bound, it will automatically bind. Otherwise, press and release the “BIND” button
on the receiver to initiate binding. On the receiver is a timeout of one minute for after power up
to enter bind mode. If the status LED will start blinking slowly the receiver has switched
successfully to bind mode.
4. Within a few seconds the process will finish with a “Binding complete” message on the
standard transmitter, or a solid green LED on the micro transmitter. The receiver has now stored
the unique serial number of that particular CROSSFIRE transmitter. If it doesn’t bind, please
verify that your firmware is to the newest version on both the receiver and the transmitter.
Binding procedure
Eachine US65/DE65 PRO 1-2S 65mm Brushless FPV whoop Tbs crsf version
Package includes
US65 PRO or DE65 PRO Frame and canopy
Option1: CrazybeeX FR V1.0 built-in internal Frsky SPI D8/D16 receiver
Option2: CrazybeeX FS V1.0 built-in internal Flysky SPI receiver
Option3:CrazybeeX PNP V1.0 with External Frsky RXSR receiver
Option4:CrazybeeX PNP V1.0 with External TBS crossfire nano receiver
Eachine NX0802 KV14000 brushless motor
Gemfan 1219-3 Propellers(4cw+4ccw)
Caddx Ant 1200TVL Global WDR with OSD 2g Ultra Light Nano FPV Camera
5.8G 25mw 40ch vtx (Flight controller built-in)
1S 250mah 30C LiHV Battery
Multi port LIPO/LIHV Battery Charger with 12V adapter
Screw Driver
Propeller disassemble tool
Eachine Handbag
Qty
1
1
1
1
1
1
4
1
1
1
1
Item Name
Features
24gram 1-2s brushless 65mm whoop
New AIO 4in1 CrazybeeX flight controller
Smooth and powerful
CADDX ANT Camera
High performance 2.0 plug
Specifications
Brand Name: Eachine
Item Name: US65 PRO/DE65 PRO
Wheelbase: 65mm
Size: 81mmx81mmx39mm
Weight: 24g(without battery)
Receiver option
Internal SPI Frsky version (Compatible with ACCST D8/D16, Recommend D8 mode)
Internal SPI Flysky version(Compatible with AFHDS and AFHDS-2A Flysky transmitter)
External Frsky RXSR receiver version(ACCST D16 sbus output)
External TBS Crossfire Nano receiver version
Flight controller connection diagram
Toggle the AUX1 Switch, the Green LED on Toggle the AUX1 Switch, the Green LED on
the Flight controller will getting to be solidthe Flight controller will getting to be solid
Toggle the AUX1 Switch, the Green LED on
the Flight controller will getting to be solid
TX2
RX2
LED_STRIP
BOOT
M1
M2
M3 M4
+5V
GND
TX1
RX1

2-6S Lipo Input
DC 12V Input
4.2V/4.35V charging switch
Charging currents switchCharging currents switchCharging currents switch
Solid LED---Charging
LED OFF---Charging complete
Ports are numbered 1-6. Do not put more than one battery on a single port. For
example: do not insert one battery on the Picoblade 1.25 plug and another on the
same port with the PH 2.0 plug.
USB 5V out
Firmware update
Mixer type and ESC/motor protocol
VTX Bands and Channels setup
Frequency and channel frequency table
CH
FR
Band1(A)
Band2(B)
Band3(E)
Band4(F)
Band5(R)
CH1
5865M
5733M
5705M
5740M
5658M
CH2
5845M
5752M
5685M
5760M
5695M
CH3
5825M
5771M
5665M
5780M
5732M
CH4
5805M
5790M
5665M
5800M
5769M
CH5
5785M
5809M
5885M
5820M
5806M
CH6
5765M
5828M
5905M
5840M
5843M
CH7
5745M
5847M
5905M
5860M
5880M
CH8
5725M
5866M
5905M
5880M
5917M
There are 2 ways to switch the vtx channels:
1.If we need to use Channel 5705 then we should Go to Betaflight CLI,type the command:
Set VTX_band=3
Set VTX_channel=1
save
2.Disarm the US65 PRO/DE65 PRO and then move the stick of the transmitter
(THR MID+YAW LEFT+PITCH UP)to enter OSD Menu,Enter to Features,then enter to VTX SA to set
VTX Band and channel
Fix the CW propeller onto the M2
and M3 motor (CW motors)
Fix the CCW propellers onto the M1
and M4 motor (CCW motors)
Props Out
Eachine US65/DE65 PRO 1-2S 65mm Brushless FPV whoop Tbs crsf version
Default PID setting
3. Open the Device Manager of your computer, find the Ports, please make sure the Com port Serial
Number is under 255, otherwise it will can't connect to the BLHELISUITE. You can change the port
serial number like the bellowing step :
4. Open the BLHELISUITE, Select SILABS BLHeli Bootloader (Cleanflight) from the third tab on
the top side. Then Select the right Serial com port and Click connect. You can also Flash the
new release BLHeli_s firmware via the BLHEILISUITE, the firmware Target is “S-H-50”
Flight controller firmware update
1. Install latest STM32 Virtual COM Port Driver
http://www.st.com/web/en/catalog/tools/PF257938
2. Install STM BOOTLOAD Driver (STM Device in DFU MODE)
3. Open Betaflight configurator and choose firmware target “CRAZYBEEF4DX(LEGACY)”,then
select the firmware version.
4. There are 2 ways to get in DFU Mode: 1). solder the boot pad and then plug USB to computer 2).
loading betaflight firmware and hit “flash”, then it will getting into DFU Mode automatically.
5. Open Zadig tools to replace the drivers from STM32 Bootloader to WINUSB Driver.
6. Reconnect the flight controller to the computer after replace driver done , and open
Betaflight Configurator, loading firmware and flash.
1. Download New release Blhelisuite from:
https://www.mediafire.com/folder/dx6kfaasyo24l/BLHeliSuite
2. Plug the usb and connect the flight controller to computer
ESC Check and Flash firmware
Set one channel of your radio transmitter to activate the Flip over function in the Mode tab of Betaflight
configurator.
The default Switch for Activate “Flip" is AUX3(Channel7)
Crashed Disarm
The Quad
Activate
Flip over
Arm
The Quad
Move stick
to flip the Quad
“Flip over after crash” procedure
Click check to see the
details of the 4in1 ESC
Flash firmware
Firmware target