Eastwood 14142 User manual

PLASMA CUTTING TABLE
INSTRUCTIONS
Part #14142

2Eastwood Technical Assistance: 800.544.5118 >> [e-mail]
Your Eastwood Plasma Cutting Table offers you an industrial solution to a problem most hobbyist face when trying to cut material with their plasma cutter or
gas torch. Using this table you can lay your work piece over the support slats and make cuts with your plasma cutter or gas torch and not worry about what to
use to support the back side of the material. The 250 pound capacity allows you to layout even heavy plate steel, make your cuts and not worry about pieces
falling to the floor.
WARNINGS
• Always wear the proper ANSI-approved eye and skin protection when plasma cutting.
• Always wear safety glasses and follow common practices when using hand tools.
INCLUDES
A. Legs (4)
B. Short Leg Brace (2)
C. Long Leg Brace (2)
D. Short Table Edge (2)
E. Long Table Edge (2)
F. Cutting Slats (23)
G. Hardware - 8mm bolts and nuts; 10mm bolts and nuts
A.
B.
G.
F.
E.
D.
C.

To order parts and supplies: 800.345.1178 >> eastwood.com 3
ASSEMBLY
1. Lie out and connect two of the Legs (A) with one of the Short Leg Braces (B). All the legs are identical so they can be used in every position (Fig 1).
2. Install two of the smaller 8mm nuts and bolts through each of the Legs (A) and Short Leg Braces (B). Do not tighten the bolts at this time.
Assemble the entire table with the nuts only finger tight and after assembly wrench tighten each of the nuts securely (Figs 2, 3).
Fig. 2
Fig. 2
Fig. 3
Fig. 3
Fig. 1
Fig. 1

4Eastwood Technical Assistance: 800.544.5118 >> [e-mail]
3. Install each of the Long Leg Braces (C) to the Legs (A) in Step 2 (Figs 4, 5, 6).
Fig. 4
Fig. 4
Fig. 5
Fig. 5
Fig. 6
Fig. 6

To order parts and supplies: 800.345.1178 >> eastwood.com 5
4. Install two Legs (A) on the opposite side and connect them with a Short Leg Brace (B) using the small 8mm bolts and nuts (Fig 7).
Fig. 7
Fig. 7

6Eastwood Technical Assistance: 800.544.5118 >> [e-mail]
5 . Using the large 10mm nuts and bolts, install the four table edges (D, E) with the cut grooves in the up and inner position (Fig 8).
Insert the bolts through the legs and into the table edges (Fig 9).
Fig. 9
Fig. 9
Grooves on long piece
Grooves on long piece
Fig. 8
Fig. 8

To order parts and supplies: 800.345.1178 >> eastwood.com 7
6. With the entire frame of the table assembled and on a level surface, you can now tighten each of the bolts (Fig 10).
7. After the assembly of the frame is complete you can install each of the cutting slats. These simply rest in the grooves cut into the table edge.
These slats are a wear item and over time they can be flipped over to achieve a flat surface and eventually will need to be replaced (Fig 11).
Fig. 10
Fig. 10
Fig. 11
Fig. 11

© Copyright 2013 Easthill Group, Inc. Instruction part #14142Q Rev. 4/13
If you have any questions about the use of this product, please contact
The Eastwood Technical Assistance Service Department: 800.544.5118 >> email: [e-mail]
PDF version of this manual is available online >> eastwood.com/14142manual
The Eastwood Company 263 Shoemaker Road, Pottstown, PA 19464, USA
US and Canada: 800.345.1178 Outside US: 610.718.8335
Fax: [phone] eastwood.com
8. After installing the slats the assembly of the Eastwood Plasma Cutting Table in complete. You can now begin using your plasma cutter to cut out pieces of
material without the worry of cutting through your support surface (Fig 12).
Fig. 12
Fig. 12