Eaton Power Xpert Gateway 900 User manual

Figure 1. Dimensions of the PXG 900 Advanced Display - 12” Color Touchscreen (PXG900-DISP-12).
8.94
(227)
13.31
(338.07)
Behind panel surface for mounting hardware
0.33
(8.4)
2.04
(51.7)
1.80
(45.7)
3.94
(100)
3.76
(95.5)
11.85
(301)
12.56
(319)
9.76
(248)
7.34
(186.4)
9.65
(245)
3.94
(100)
9.65
(245)
Behind panel surface for mounting hardware
Effective October 2017
Technical Data TD150022EN
Power Xpert Gateway 900 Advanced Color
Touchscreen Display Quick Start Guide
For detailed information concerning the operation and features
available in the PXG 900 Advanced Display - 12” Color Touchscreen
(PXG900DISP-12), please refer to the Eaton Power Xpert Gateway
900 User’s Guide (MN152006EN) available on the Eaton website
(www.eaton.com/pxg) for information on Web Server Screens.
Installation
1. Disconnect and lockout all power to the enclosure.
2. Inspect the enclosure door to determine the best mounting loca-
tion for the PXG 900 Advanced Display.
ote:N A minimum clearance of 1 in. (25.4 mm) must be maintained
between the back of the display and any other component within the
enclosure.
3. Use the mounting template to mark the cutout area on the
enclosure door. Cut out the marked area.
Figure 2. PXG 900 Advanced Display.
Figure 3. Cut out dimensions.
9.02
(229)
11.93
(303)
Mounting hole

2
Technical Data TD150022EN
Effective October 2017
Power Xpert Gateway 900 Advanced Color
Touchscreen Display Quick Start Guide
EATON www.eaton.com
4. Insert the PXG 900 Advanced Display through the cutout. After
the display is inserted into the front side of the cutout, secure
the display by attaching the eight supplied fasteners to the rear
perimeter of the display.
Figure 4. PXG 900 Advanced Display fasteners.
5. Check for proper alignment of the PXG 900 Advanced Display
then torque fasteners to 7 lb-in. (0.8 N·m).
Figure 5. PXG 900 Advanced Display fasteners - installed.
Setting up the PXG 900 for display
In order for the display to function properly, the Power Xpert
Gateway 900 (PXG 900) must not timeout after inactivity. This set-
ting can be changed by following the instructions below.
1. Begin by installing the Power Xpert USB configuration driver
on your PC. The driver and instructions can be found at
www.eaton.com/pxg
2. Connect the PXG 900 to a PC with the accompanying USB cord.
3. With a browser, visit the IP address 192.168.200.101.
4. Select Settings >Security >General >Edit.
5. Set the Session Timeout to 0.
6. Click the Save button.
Figure 6. Editing session timeout.
The display requires an account with the user name and a password
of the user. This account exists by default. This can be confirmed
with the instructions below.
1. With a PC connected to the PXG 900 via USB, navigate to
192.168.200.101.
2. Select Settings > Security > User Configuration. All existing user
access credentials are shown.

3
Technical Data TD150022EN
Effective October 2017
Power Xpert Gateway 900 Advanced Color
Touchscreen Display Quick Start Guide
EATON www.eaton.com
Figure 7. User accounts.
3. If a “user” account does not exist, or if the password needs to
be changed, this can be corrected by clicking on the Edit button
in the upper right hand corner of the screen.
4. If the “user” account does not exist, add it with the Add User
button.
5. If the password needs to be corrected, select the return the
password to the default of user by selecting the arrow to pull out
the side-pane and change the password.
Figure 8. Updating password.
Connections
To use the PXG 900 Advanced Display, provide power through the
included connector. This display accepts an input from 9-36 Vdc with
a maximum power consumption of 60 W.
ote:N A power supply must be purchased as it is not supplied with the dis-
play. Eaton recommends the following power supplies: PSG60E (85-264 Vac
input); PSG60F (320-575 Vac input).
The display’s plug-in terminals provide connections for +V, -V, and
floating ground.
Figure 9. Power and COM port connections for the PXG 900
Advanced Color Touchscreen Display.
Figure 10. Power port connection.
The PXG 900 Advanced Color Touchscreen Display requires a USB
cable (included with the PXG 900). This connects directly to the
USB Local Configuration port on the PXG 900 and can be plugged
into either USB port on the display.
USB connection
To DC power supply
display power input range:
9-36 Vdc
minimum 60 W

4
Technical Data TD150022EN
Effective October 2017
Power Xpert Gateway 900 Advanced Color
Touchscreen Display Quick Start Guide
EATON www.eaton.com
Figure 11. COM port connections.
Display hot-spots
There are a handful of hot-spots that aid with navigation. An on-
screen keyboard can be called by tapping in the upper left corner.
The keyboard will be hidden when it is closed.
If connection to the PXG 900 is lost, open the keyboard and use
Ctrl+R to refresh the page.
Figure 12. Access to the keyboard.
LAN 1
(Reserved for factory
configuration)
LAN 2
USB 2.0 (top)
USB 3.0 (bottom)
Alternative power
connection
Audio jack
COM 1 COM 2
To scroll, tap the empty section of any scrollbar.
Figure 13. Scrolling.
Tap the upper
left corner to
unhide on-
screen
keyboard
Tap to scroll

5
Technical Data TD150022EN
Effective October 2017
Power Xpert Gateway 900 Advanced Color
Touchscreen Display Quick Start Guide
EATON www.eaton.com
PXG 900 firmware requirements
The minimum gateway firmware version required for compatibility is
4.2.2.
Technical information
• 1024 x 768 pixel backlit LCD graphic touch screen display.
• Power: 9–36 Vdc input.
• Recommended power supplies: PSG60E (85-264 Vac input);
PSG60F (320-575 Vac input).
Display measurements
• Height: 9.65 in. (245 mm);
• Width: 12.56 in. (319 mm);
• Depth: 2.00 in. (52 mm);
• Shipping weight: 2.1 lb (2.5 kg);
• Cutout dimensions: 11.90 x 9.00 in. (303 x 229 mm).
Ratings
• Front Bezel IP rating: IP65;
• Operating temperature: 0 ~ 50°C (32 ~ 122°F);
• Storage temperature: -20 ~ 60°C (-4 ~ 140°F);
• Storage humidity: 10%~90%, non-condensing.

Technical Data TD150022EN
Effective October 2017
Power Xpert Gateway 900 Advanced Color
Touchscreen Display Quick Start Guide
Eaton
Electrical Sector
1000 Eaton Boulevard
Cleveland, OH 44122
United States
877-ETN-CARE (877-386-2273)
Eaton.com
© 2017 Eaton
All Rights Reserved
Printed in USA
Publication No. TD150022EN / TBG001372
October 2017
Eaton is a registered trademark.
All other trademarks are property of their
respective owners.