Eaton EG-2 User manual

EG-2
Ethernet Gateway
Installation guide

Eaton Lighting Systems iLight Product Series - EG-2 9850-000224-02 2
Contents
Introduction 3
Basic Schematic 3
Installation 3
Product Overview 4
Connecting the Supply 5
iCAN Network Connections 5
Set Up Instructions 6
Configuration 6
Setting the IP address 6-7

Eaton Lighting Systems iLight Product Series - EG-2 9850-000224-02 3
Introduction
The Ethernet Gateway 2 provides
connection between an iLight CAN
network and an Ethernet LAN. This allows
a user to control and configure the iLight
system using iCANsoft on a LAN network
PC rather than by connecting directly into
the network.
The EG2 also facilitates connection to the
internet when installed behind a firewall.
This then enables remote connection for
controlling, programming and obtaining
diagnostics of the lighting control system.
The EG2 also functions as a smartphone
device host allowing control and
programming of the iLight network. Apps
are available free of charge for Android
and Apple devices.
Facilities are provided to allow a BMS or
smart home system to interact with the
iLight network. This is achieved by simple
character strings communicated via a UDP
or TCP connection.
Basic Schematic
Installation
Location
The EG2 should be installed in a dry ventilated
location, where ambient conditions are main-
tained within the requirements of the unit. The
unit has ventilation slots on its sides to allow
convection cooling and in no circumstances
should these be blocked.
Mounting
Always mount in well ventilated location Allow
50mm (2”) above and below the unit if trunking
with a depth greater than 50mm (2”) is used.
Ambient atmosphere requirements
Temperature: +2°C to +40°C (+36°F to +104°F)
Humidity: 5% to 95% non-condensing
IP Rating: IP20
Weight:
0.25Kg (0.55 lbs)
Dimensions

Eaton Lighting Systems iLight Product Series - EG-2 9850-000224-02 4
Ethernet LINK
LED on indicates the
link is connected at
100Mb
LED off indicates the
link is connected at
10Mb
Ethernet DATA
LED on indicates that
the Ethernet link is
established
LED flashes off briefly
when Ethernet traffic is
present
SD card DATA
LED flashing indicates
memory card is being
accessed
SD card INPUT
Indicates SD Memory
card location
iCAN DATA
Red flashing LED indicates
traffic being sent and/or
received
Red LED on indicates a
CANbus error
iCAN IDENT
Switch that causes the EG2 to
send a message on the CAN
BUS to identify itself
iCAN status
Green flashing LED indicates
normal operation
Product Overview
The label on the enclosure identifies the position of the status LEDS, switches & connectors.
iCAN Network
For connection
see P6 for wiring
details
TIMECLOCK
Set through iLight
programming
software.
LED on when
timeclock active
RESET
Switch that resets
the device. Only
press this on
direct instruction
from Eaton
to avoid data
corruption
Ethernet INPUT
Indicates Ethernet
connector location
POWER
The Green Power
LED will double flash
continuously while
EG2 is on.
CAN Termination
End of network
termination jumper.

Eaton Lighting Systems iLight Product Series - EG-2 9850-000224-02 5
Connecting the Supply
Power is to be supplied to the EG2 via an external
regulated power supply in the range of 9-36VDC
0.3A
Eaton are able to provide a recommended power
supply if required.
Catalogue Number: PSU-15-DIN (15VDC 0.67A)
A removable 2 way connector screw terminal
plug is provided for the connection of the power
supply. Terminal sizes: 2 x 1.5mm2
iCAN Network Connections
A removable 5 way connector screw terminal
plug is provided for the connection of iCAN
network cables. Terminal sizes: 5 x 1.5mm²
IMPORTANT NOTE: Connecting a mains
potential cable to the iCAN Network terminals
is likley to damage the unit and others
connected, and invalidate warranty.
Function Cable Colours
+12Vdc Red
CAN H Blue
Shield Silver
CAN L White
0V Black
+V
0V
CAN-L
SHIELD
CAN-H
0V
+12V
iCAN devices are ‘daisy-chained’ on the
network. Spurs from the Network are not
permitted and will result in communications
problems. Devices on an iCAN network can be
wired in any order. Termination is required at
both ends of the network.
Network Termination
T - Indicates where a termination is required.
The EG-2 has built-in network termination. If
the EG-2 is at the end of the network, ensure
the CAN TERMINATION jumper is fitted in the
Termination On position.
Termination On
Termination Off
iCAN
Device
iCAN
Device
EG2

Eaton Lighting Systems iLight Product Series - EG-2 9850-000224-02 6
Set Up Instructions
iCAN Network
Connect the EG2 to the iCAN network using the network connector. If the EG2 is at the end of a
network set the Term link to ON otherwise set to the OFF position
Ethernet
Ethernet connection by RJ45 (568B). This should be connected to either an Ethernet Switch or to
a Wireless Router.
Configuration
iCAN Device Number
The EG2 is supplied with a iCAN Network Device number with Segment number 255 and a
node number in the range 1-255. Both Segment and Node number can be changed using iLight
programming software.
Factory Default IP settings
IP Address: 192.168.0.100
Subnet mask: 255.255.255.0
Gateway: 192.168.0.254
DHCP: Off
Note: The EG2 default settings are to use a fixed IP address of 192.168.0.100. Any device used to
communicate with the EG2 will need to be located within the 192.168.0.x subnet.
Power up
The EG2 takes approximately 60 seconds to be ready for use once power is applied.
Wait for the Green CAN LED to flash slowly.
The Green Power LED will double flash continuously while EG2 is on.
Setting the IP address
The factory set IP Address can be changed using the iCAN network connection or using a
computer connected directly to the Ethernet port.
Changing with iCAN Network
Connect to the iCAN network a computer running iLight programming software using an iLight PC
Node. Search the network and load the EG2 into the software.
Go the Ethernet tab. Either the Default settings can be applied or other settings can be applied.
Select OK or Apply to download the changes to the EG2.

Eaton Lighting Systems iLight Product Series - EG-2 9850-000224-02 7
Change IP address via the Ethernet port
EG2 is supplied from the factory without DHCP enabled; therefore, it is necessary that the
Ethernet port of the PC is set to the correct IP Address and Subnet Mask. For details of setting
the IP address of your computer consult information on line. This will depend on your Operating
System.
Example
IP Address: 192.168.0.99
Subnet mask: 255.255.255.0
Gateway: 192.168.0.254
To connect the EG2 directly to the PC, it may be necessary to use a Crossover Cable, however,
most modern computers are able to connect directly to another Ethernet device without a
crossover cable.
The Ethernet port of your computer will need to configured to a compatible IP address.
Open iLight programming software. It will be required to set the software to communicate using
the Ethernet Port.
This is done by selecting from the Tool bar Tools>Options>Network.
Select Ethernet Gateway and change the IP address to 192.168.0.100. Also ensure the ‘Use
Select OK to confirm and set the address.
The software can now be used to configure
any items connected on the network.
Set the IP address of the EG2 as described
in section opposte. The new IP address will
become valid when the EG2 is reset or power
to the device is removed and re-instated.
Reset to factory defaults
Factory defaults may be reset by the following procedure:
Remove power from the board.
Press the CAN ID button and reapply power. Keep the button pressed until the CAN LED flashes
then stays on. At this point the Ethernet settings will have been restored to defaults.
After setting to factory defaults, the IP address of the device will revert to 192.168.0.100

Document: EG-2 9850-000224-02
Eaton Lighting Systems
Usk House, Lakeside, Llantarnam Park, Cwmbran, NP44 3HD, UK
T: [phone] F: [phone]
E: [email protected] EatonLightingSystems.com
iLight Technical Support
Tel: [phone] (available Mon-Fri 9am-5pm GMT)
Email: Tec[email protected]
Web: www.iLight.co.uk
All products manufactured by Eaton Lighting Systems and identified with the iLight product series
mark are warranted to be free from defects in material and workmanship and shall conform to and
perform in accordance with Seller’s written specifications.
This warranty will be limited to the repair or replacement, at Seller’s discretion, of any such goods
found to be defective, upon their authorized return to Seller. This limited warranty does not apply
if the goods have been damaged by accident, abuse, misuse, modification or misapplication, by
damage during shipment or by improper service.
There are no warranties, which extend beyond the hereinabove-limited warranty,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE
IMPLIED WARRANTY OF FITNESS.
No employee, agent, dealer, or other person is authorised to give any warranties on behalf of the
Seller or to assume for the Seller any other liability in connection with any of its goods except in
writing and signed by the Seller. The Seller makes no representation that the goods comply with
any present or future federal, state or local regulation or ordinance. Compliance is the Buyer’s
responsibility.
The use of the Seller’s goods should be in accordance with the provision of the National Electrical
Code, UL and/or other industry or military standards that are pertinent to the particular end use.
Installation or use not in accordance with these codes and standards could be hazardous.
!
WARNING HAZARDOUS VOLTAGES
DISCONNECT FROM SUPPLY
BEFORE REMOVING COVERS
NO USER SERVICEABLE PARTS INSIDE
SERVICE BY QUALIFIED PERSONNEL ONLY
WARNING
To reduce the risk of fire or electric shock,
DO NOT expose this device to rain or moisture.
DO NOT energise unless the front cover is in place.
This device must be earthed.
Installation, programming and maintenance must be carried out by qualified personnel.
Eaton Lighting Systems cannot accept responsibility for repairs or modifications that are not
competently executed and in accordance with service or upgrade information.
CE compliant to all relevant standards