Eaton IQ 100 series Guide

IQ 100 Series (130/140/150)
Meter User & Installation Manual
IM02601003E
Rev D

Copyright (c) 2010 by Eaton Corporation.
All rights reserved.
Specications contained herein are subject
to change without notice.
Power Xpert and PowerVision are registered
trademarks of Eaton
Corporation.
EATON CORPORATION - CONFIDENTIAL
AND PROPRIETARY NOTICE TO PERSONS
RECEIVING THIS DOCUMENT AND/OR
TECHNICAL INFORMATION.
THIS DOCUMENT, INCLUDING THE DRAW-
ING AND INFORMATION CONTAINED
THEREON, IS CONFIDENTIAL AND IS THE
EXCLUSIVE PROPERTY OF EATON CORPO-
RATION, AND IS MERELY ON LOAN AND
SUBJECT TO RECALL BY EATON AT ANY
TIME. BY TAKING POSSESSION OF THIS
DOCUMENT, THE RECIPIENT ACKNOWL-
EDGES AND AGREES THAT THIS DOCU-
MENT CANNOT BE USED IN ANY MANNER
ADVERSE TO THE INTERESTS OF EATON,
AND THAT NO PORTION OF THIS DOCU-
MENT MAY BE COPIED OR OTHERWISE
REPRODUCED WITHOUT THE PRIOR WRIT-
TEN CONSENT OF EATON. IN THE CASE
OF CONFLICTING CONTRACTUAL PROVI-
SIONS, THIS NOTICE SHALL GOVERN THE
STATUS OF THIS DOCUMENT.

IQ 100 Series ((130/140/150) Meter
Table of Contents
User and Installation Manual IM02601003E - July 2010 www.eaton.com 3
Table of Contents
Disclaimer of Warranties and Limitation of Liability 7
Support Services 9
Support Services 9
Website 9
EatonCare Customer Support Center 9
Technical Resource Center 10
European PanelMate Support Center 10
For Customers in Europe, contact: 10
Repair and Upgrade Service 10
Additional support is also available from our well-equipped 10
Repair and Upgrade Service (support for OI) 10
IQ 100 Series Meter Overview and Specications 11
Hardware Overview 11
IQ 100 Series Meter / Digital Transducer 11
IQ 100 Series Digital Transducer 11
Voltage and Current Inputs 11
Universal Voltage Inputs 11
Current Inputs 12
Ordering Information 12
Measured Values 13
Utility Peak Demand (IQ140/150) 14
Specications 14
Compliance 16
Accuracy 16
IQ 100 Series Mechanical Installation 17
Introduction 17
ANSI Installation Steps 18
DIN Installation Steps 19
IQ 100 Series Transducer Installation 20
IQ 100 Series Electrical Installation 21
Considerations When Installing Meters 21
CT Leads Terminated to Meter 22
CT Leads Pass-Through (No Meter Termination) 23
Quick Connect Crimp CT Terminations 24
Voltage and Power Supply Connections 25
Ground Connections 25
Voltage Fuses 25
Electrical Connection Diagrams 26
1. Service: WYE, 4-Wire with No PTs, 3 CTs 26
2. Service: 2.5 Element WYE, 4-Wire with No PTs, 3 CTs 27
3. Service: WYE, 4-Wire with 3 PTs, 3 CTs 28
4. Service: 2.5 Element WYE, 4-Wire with 2 PTs, 3 CTs 29

IQ 100 Series (130/140/150) Meter
Table of Contents
4 User and Installation Manual IM02601003E-July 2010 www.eaton.com
5. Service: Delta, 3-Wire with No PTs, 2 CTs 30
6. Service: Delta, 3-Wire with 2 PTs, 2 CTs 31
7. Service: Delta, 3-Wire with 2 PTs, 3 CTs 32
8. Service: Current Only Measurement (Three Phase) 33
9. Service: Current Only Measurement (Dual Phase) 34
10. Service: Current Only Measurement (Single Phase) 35
IQ 100 Series Communication Installation 37
RS485 / KYZ Output (Communication Option) 37
For All RS485 Connections: 38
IQ 100 Series Transducer Communication Information 40
Meter Connection 40
Programming the IQ 100 Series Meter Using the Front Panel 41
Introduction 41
Understanding Meter Face Elements 41
Understanding Meter Face Buttons 41
Using the Front Panel 42
Understanding Startup and Default Displays 42
Using the Main Menu 43
Using Reset Mode 43
Entering a Password 44
Using Conguration Mode 45
Conguring the Scroll Feature 46
Conguring CT Setting 47
Conguring PT Setting 48
Conguring Connection Setting 49
Conguring Communication Port Setting 49
Using Operating Mode 50
Understanding the % of Load Bar 51
% of Load Segment Table 51
Performing Watt-Hour Accuracy Testing (Verication) 52
Programming the IQ 100 Series Meter Using Software 53
Overview 53
Connecting to the IQ 100 Series Meter/Transducer 53
Accessing the IQ 100 Series Device Prole 54
Performing Device Prole Tasks 55
Conguring Settings 56
Conguring Scaling 56
Functional Overview of CT and PT Ratios: 56
Conguring Energy and Display Settings 57
Conguring Communication Settings 58
Conguring (System) Settings 58
Polling the IQ 100 Series Meter 59
Instantaneous Polling 59
Poll Power and Demand 60
Poll Phasors 61

IQ 100 Series ((130/140/150) Meter
Table of Contents
User and Installation Manual IM02601003E - July 2010 www.eaton.com 5
Using the IQ 100 Series Tools Menu 62
Accessing the Device Prole Screen 62
Reset Device Information 62
Retrieve Device Status 62
Flash Update Firmware 62
Performing Additional Tasks with Eaton Meter Conguration Software 63
Using Connection Manager 63
Disconnecting from an IQ 100 Series meter 65
Changing the Primary Device/Address 65
Merging Connection Databases 65
Using the Options Screen 66
Using the Help Menu 66
App. A: IQ 100 Series Navigation Maps 67
Introduction 67
Navigation Maps (Sheets 1 to 4) 67
Main Menu Screens (Sheet 1) 68
Operating Mode Screens (Sheet 2) 69
Reset Mode Screens (Sheet 3) 70
Conguration Mode Screens (Sheet 4) 71
App.B Modbus Mapping for IQ 100 Series 73
Introduction 73
Modbus Register Map Sections 73
Floating Point Values 74
Important Note Concerning the IQ 100 Series Modbus Map 75
Modbus Register Map (MM-1 to MM-16) 75

IQ 100 Series (130/140/150) Meter
Table of Contents
6 User and Installation Manual IM02601003E-July 2010 www.eaton.com

IQ 100 Series ((130/140/150) Meter
Disclaimer of Warranties and Limitation of Liability
User and Installation Manual IM02601003E - July 2010 www.eaton.com 7
Disclaimer of Warranties and Limitation of Liability
The information, recommendations, descriptions and safety notations in this document are based on
Eaton Corporation’s (“Eaton”) experience and judgment and may not cover all contingencies. If further
information is required, an Eaton sales ofce should be consulted. Sale of the product shown in this
literature is subject to the terms and conditions outlined in appropriate Eaton selling policies or other
contractual agreement between Eaton and the purchaser. THERE ARE NO UNDERSTANDINGS,
AGREEMENTS, WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF FITNESS FOR A
PARTICULAR PURPOSE OR MERCHANTABILITY, OTHER THAN THOSE SPECIFICALLY SET OUT IN ANY
EXISTING CONTRACT BETWEEN THE PARTIES. ANY SUCH CONTRACT STATES THE ENTIRE OBLIGA-
TION OF EATON. THE CONTENTS OF THIS DOCUMENT SHALL NOT BECOME PART OF OR MODIFY
ANY CONTRACT BETWEEN THE PARTIES.
In no event will Eaton be responsible to the purchaser or user in contract, in tort (including negligence),
strict liability or otherwise for any special, indirect, incidental or consequential damage or loss
whatsoever, including but not limited to damage or loss of use of equipment, plant or power system,
cost of capital, loss of power,additional expenses in the use of existing power facilities, or claims
against the purchaser or user by its customers resulting from the use of the information, recommenda-
tions and descriptions contained herein.

IQ 100 Series (130/140/150) Meter
Disclaimer of Warranties and Limitation of Liability
8 User and Installation Manual IM02601003E-July 2010 www.eaton.com

IQ 100 Series ((130/140/150) Meter
Support Services
User and Installation Manual IM02601003E - July 2010 www.eaton.com 9
Support Services
Support Services
The goal of Eaton is to ensure your greatest possible satisfaction
with the operation of our products. We are dedicated to
providing fast, friendly and accurate assistance. That is why we
offer you so many ways to get the support you need. Whether
it’s by phone, fax or e-mail, you can access Eaton’s support
information 24 hours a day, seven days a week. Our wide range
of services is listed below.
You should contact your local distributor for product pricing,
availability, ordering, expediting and repairs.
Website
Use the Eaton website to nd product information. You can also
nd information on local distributors or Eaton’s sales ofces.
Website Address
www.eaton.com/electrical
EatonCare Customer Support Center
Call the EatonCare Support Center if you need assistance with
placing an order, stock availability or proof of shipment,
expediting an existing order, emergency shipments, product
price information, returns other than warranty returns, and
information on local distributors or sales ofces.
Voice: 877-ETN CARE (386-2273) (8:00 am – 6:00 pm EST)
FAX: [phone]
After-Hours Emergency: 800-543-7038
(6:00 pm – 8:00 am EST)
If you are in the US or Canada, and have OI or PLC questions,
you can take advantage of our toll-free line for technical
assistance with hardware and software product selection,
system design and installation, and system debugging and
diagnostics. Technical support engineers are available for calls
during regular buiness hours.

IQ 100 Series (130/140/150) Meter
Support Services
10 User and Installation Manual IM02601003E-July 2010 www.eaton.com
Technical Resource Center
Voice: 877-ETN CARE (386-2273) (8:00 am – 5:00 pm EST)
FAX: [phone]
e-mail: [email protected]
European PanelMate Support Center
This engineering company, located in Zurich, Switzerland,
provides high-level quality support and repair assistance for your
PanelMate products. You will receive technical and application
support.
For Customers in Europe, contact:
BFA Solutions, Ltd.
Voice: [phone] (9:00 am – 5:00 pm CET)
e-mail: [email protected]
www.bfa.ch
Repair and Upgrade Service
Additional support is also available from our well-equipped
Repair and Upgrade Service department. If you have questions
regarding the repair or upgrade of OI product, contact your local
distributor.
Repair and Upgrade Service (support for OI)
Voice:
877-ETN-CARE (877-386-2273) (8:00 am – 5:00 pm EST)
414-449-7100 (8:00 am – 5:00 pm EST)
FAX: [phone]
e-mail: [email protected]