Eaton IQ 200 User manual

TD 17558
Effective 3/98
Instructions for Installation, Operation,
and Maintenance of Cutler-Hammer IQ 200
Electrical Distribution System Meter

TD 17558 Page i
Effective 3/98
Table of Contents
SECTION 1: INTRODUCTION...................................................................1
1.1 PRELIMINARY COMMENTS AND SAFETY PRECAUTIONS ...............1
1.1.1 Warranty and Liability Information..........................................1
1.1.2 Safety Precautions.................................................................1
1.1.3 Factory Correspondence........................................................2
1.2 PRODUCT OVERVIEW.......................................................................2
SECTION 2: HARDWARE DESCRIPTION..............................................4
2.1 GENERAL...........................................................................................4
2.1.1 IQ 200 Display Module...........................................................4
2.1.2 IQ 200 Base Module..............................................................4
2.1.3 Installation.............................................................................4
2.2 OPERATOR PANEL............................................................................5
2.3 BASE MODULE REAR ACCESS AREA...............................................5
2.3.1 Current and Voltage Inputs ....................................................6
2.3.2 Power Supply Input................................................................6
2.3.3 Local Display Connection.......................................................6
2.3.4 INCOM™ Communications....................................................6
2.4 EXTERNAL HARDWARE.....................................................................7
2.4.1 Current Transformers.............................................................7
2.4.2 Potential Transformers...........................................................7
2.4.3 External Fuses ......................................................................7
2.5 PRODUCT SPECIFICATIONS.............................................................7
2.5.1 Regulatory/Standards Compliance.........................................8
2.6 ORDERING INFORMATION..............................................................11
SECTION 3: INSTALLATION....................................................................12
3.1 INTRODUCTION...............................................................................12
3.2 PANEL PREPARATION.....................................................................12
3.2.1 Mounting the IQ 200 Modules as a Single Unit.....................13
3.2.2 Mounting the IQ 200 Display and Base Modules Separately..13
3.3 WIRING.............................................................................................16
3.3.1 Wiring System Current and Voltage......................................16

Page ii TD 17558
Effective 3/98
3.3.2 Wiring Diagrams for Various System Configurations..............16
3.3.3 INCOM™ Network Communications.....................................22
3.3.4 KYZ Pulse Initiator ...............................................................22
SECTION 4: OPERATION.........................................................................25
4.1 GENERAL..........................................................................................25
4.2 BUTTONS..........................................................................................25
4.3 CONTRAST.......................................................................................26
4.4 DISPLAYED SIGN CONVENTIONS ...................................................26
4.5 USING THE OPERATOR PANEL.......................................................27
4.6 SYSTEM DATA DISPLAY MODE.......................................................28
4.6.1 3 Wire System and 4 Wire System........................................28
4.7 PHASE DATA DISPLAY MODE..........................................................28
4.7.1 3 Wire System......................................................................28
4.7.2 4 Wire System......................................................................29
4.8 MIN/MAX DATA DISPLAY MODE.......................................................29
4.8.1 3 Wire System......................................................................29
4.8.2 4 Wire System......................................................................30
4.9 VIEW SETPOINTS (3 and 4 wire systems)..........................................31
4.9.1 View All................................................................................31
4.9.2 Password Setup...................................................................31
4.9.3 INCOM™ Setup...................................................................32
4.9.4 System Frequency...............................................................32
4.9.5 Wiring Configuration.............................................................32
4.9.6 CT Ratio..............................................................................33
4.9.7 PT Ratio ..............................................................................33
4.9.8 Demand Window..................................................................33
4.9.9 KYZ Setup...........................................................................33
4.9.10 Exit......................................................................................33
4.10 Edit Setpoints (3 and 4 wire systems)..................................................34
4.10.1 Edit All.................................................................................34
4.10.2 Password Setup...................................................................34
4.10.3 INCOM™Setup...................................................................35
4.10.4 System Frequency...............................................................36

TD 17558 Page iii
Effective 3/98
4.10.5 Wiring Configuration............................................................36
4.10.6 CT Ratio..............................................................................36
4.10.7 PT Ratio..............................................................................37
4.10.8 Demand Window.................................................................38
4.10.9 KYZ Setup...........................................................................38
4.10.10 Exit......................................................................................39
4.11 RESET VALUES................................................................................39
4.12 CONTRAST ADJUST ........................................................................40
4.13 DIAGNOSTICS..................................................................................40
4.14 EXIT MENU.......................................................................................40
SECTION 5: TROUBLESHOOTING AND MAINTENANCE...............41
5.1 GENERAL.........................................................................................41
5.1.1 Level of Repair....................................................................41
5.1.2 Maintenance and Care.........................................................41
5.2 REMOVAL AND REPLACEMENT......................................................41
5.2.1 General Safety Precautions .................................................42
5.2.2 IQ 200 Display Module.........................................................42
5.2.3 IQ 200 Base Module............................................................42
5.3 GENERAL TROUBLESHOOTING PROCEDURES.............................43
5.4 TECHNICAL ASSISTANCE................................................................44
5.5 RETURN PROCEDURE ....................................................................44

Page iv TD 17558
Effective 3/98
List of Figures
Figure 2.1 IQ 200 Display Module................................................................4
Figure 2.2 IQ 200 Base Module...................................................................4
Figure 2.3 Operator Panel...........................................................................5
Figure 2.4 Base Module (Rear Face View)...................................................5
Figure 3.1 Securing the IQ 200 Display Module..........................................13
Figure 3.2 Mounting the IQ 200 Base Module
to the IQ 200 Display Module.................................................13
Figure 3.3 Typical Mounting Options for Mounting
the IQ 200 Base Module........................................................14
Figure 3.4 Mounting Hole Pattern for the IQ 200 Base Module....................15
Figure 3.5 3 Phase 3 Wire Configuration (Up to 600 Volts).........................17
Figure 3.6 3 Phase 3 Wire Configuration (Above 600 Volts)........................17
Figure 3.7 3 Phase 3 Wire, 2 CT Configuration (Up to 600 Volts)................18
Figure: 3.8 3 Phase 3 Wire, 2CT Configuration (Above 600 Volts) ...............18
Figure: 3.9 3 Phase 4 Wire Configuration (Up to 600 Volts).........................19
Figure 3.10 3 Phase 4 Wire Configuration (Above 600 Volts)........................19
Figure 3.11 3 Phase 3 Wire Configuration (Above 600 Volts) Line Powered..20
Figure 3.12 3 Phase 4 Wire Configuration (Up to 600 Volts) Line Powered ...20
Figure 3.13 Single Phase 3 Wire Configuration (Up to 600 Volts)..................21
Figure 3.14 Single Phase 2 Wire Configuration (Up to 600 Volts)..................21
Figure 3.15 Securing INCOM™ Cable to Shroud..........................................22
Figure 3.16 2-Terminal (K-Y) Configuration..................................................24
Figure 3.17 3 Terminal (K-Y-Z) Configuration...............................................24
Figure 4.1 System Power Values Relationships..........................................27
Figure 4.2 Main Menu................................................................................27
Figure 4.3 System Display 3 and 4 Wire Systems.......................................28
Figure 4.4 Phase Display 3 Wire Systems..................................................29
Figure 4.5 Phase Display 4 Wire Systems..................................................29
Figure 4.6 Min/Max Data Display, 3 Wire System.......................................30
Figure 4.7 Min/Max Data Display, 4 Wire System.......................................31
Figure 4.8 No Password Required.............................................................32
Figure 4.9 Password Required...................................................................32

TD 17558 Page v
Effective 3/98
Figure 4.10 INCOM™ Setup.......................................................................32
Figure 4.11 System Frequency....................................................................32
Figure 4.12 Wiring Configuration.................................................................32
Figure 4.13 CT Ratio ..................................................................................33
Figure 4.14 PT Ratio...................................................................................33
Figure 4.15 Demand Window......................................................................33
Figure 4.16 KYZ Setup ...............................................................................33
Figure 4.17 Password Entry........................................................................34
Figure 4.18 Password Setup.......................................................................34
Figure 4.19 INCOM™ Setup.......................................................................35
Figure 4.20 System Frequency....................................................................36
Figure 4.21 Wiring Configuration.................................................................36
Figure 4.22 CT Ratio ..................................................................................36
Figure 4.23 PT Ratio...................................................................................37
Figure 4.24 Demand Window......................................................................38
Figure 4.25 KYZ Setup ...............................................................................38
Figure 4.26 Reset Values............................................................................39
Figure 4.27 Reset Energy...........................................................................39
Figure 4.28 Reset Amps Min/Max ...............................................................39
Figure 4.29 Contrast Adjust.........................................................................40

Page vi TD 17558
Effective 3/98
List of Tables
Table 2.1 IQ 200 Safety Specifications .......................................................8
Table 2.2 IQ 200 Operating Specifications..................................................9
Table 2.3 IQ 200 Metering Accuracy.........................................................10
Table 2.4 IQ 200 Measurement Ranges....................................................10
Table 2.5 IQ 200 Physical Characteristics.................................................11
Table 2.6 IQ 200 Ordering Information......................................................11

TD 17558 Page 1
Effective 3/98
Cutler-Hammer
IQ 200 Electrical Distribution System Meter
Installation, Operation, and Maintenance
SECTION 1: INTRODUCTION
1.1 PRELIMINARY COMMENTS AND SAFETY PRECAUTIONS
This Technical Document covers most aspects of installation, operation, and unit-
level maintenance of the IQ 200. This document is a guide only for authorized and
qualified personnel who select and use the IQ 200. Please refer to the specific
WARNING and CAUTION in this section before proceeding. If you require further
information regarding a particular installation, application, or maintenance activity,
contact your Cutler-Hammer representative.
1.1.1 Warranty and Liability Information
No warranties, expressed or implied, including warranties of fitness for a particular
purpose of merchantability, or warranties arising from course of dealing or usage of
trade are made regarding this information, recommendations, and descriptions
contained herein. In no event will Cutler-Hammer be responsible to the purchaser or
user in contract, in tort (including negligence), strict liability, or otherwise for any
special, indirect, incidental, or consequential damage or loss whatsoever, including
but not limited to damage or loss of use of equipment plant or power system, cost of
capital, loss of power, additional expenses in the use of existing power facilities, or
claims against the purchaser or user by its customers resulting from the use of the
information and descriptions contained herein.
1.1.2 Safety Precautions
All safety codes, safety standards, and/or regulations must be strictly observed in
the installation, operation, and maintenance of this device.
WARNING
THE WARNINGS AND CAUTIONS INCLUDED AS PART OF THE PROCEDURAL
STEPS IN THIS DOCUMENT ARE FOR PERSONNEL SAFETY AND PROTECTION
OF EQUIPMENT FROM DAMAGE. AN EXAMPLE OF A TYPICAL WARNING LABEL
IS SHOWN ABOVE IN REVERSE TYPE TO FAMILIARIZE PERSONNEL WITH THE
STYLE OF PRESENTATION. THIS WILL HELP TO ENSURE THAT PERSONNEL
ARE ALERT TO WARNINGS WHICH MAY APPEAR THROUGHOUT THE
DOCUMENT. IN ADDITION, CAUTIONS ARE ALL UPPER CASE AND BOLDFACED
AS SHOWN ON THE NEXT PAGE.

Page 2TD 17558
Effective 3/98
CAUTION
COMPLETELY READ AND UNDERSTAND THE MATERIAL PRESENTED IN THIS
DOCUMENT BEFORE ATTEMPTING TO INSTALL, OPERATE OR USE THE
EQUIPMENT. IN ADDITION, ONLY QUALIFIED PERSONS SHOULD BE PERMITTED
TO PERFORM ANY WORK ASSOCIATED WITH THE EQUIPMENT. ANY WIRING
INSTRUCTIONS PRESENTED IN THIS DOCUMENT MUST BE FOLLOWED
PRECISELY. FAILURE TO DO SO COULD CAUSE PERMANENT EQUIPMENT
DAMAGE.
1.1.3 Factory Correspondence
For additional information, technical assistance, or referral to a local authorized
distributor, contact Power Management Application Support (PMAS) at
1-800-809-2772, option 1.
1.2 PRODUCT OVERVIEW
The IQ 200 is a microprocessor based monitoring device that provides single phase,
2 or 3 wire, and 3 phase, 3 or 4 wire electrical metering designed to replace
numerous individual meters and recorders. It is compact, consisting of a panel-
mounted Display Module and a Base Module that can be attached to the Display
Module or mounted remotely. It communicates information over the Cutler-Hammer
IMPACC network. The IQ 200 is password protected, menu driven, and displays a
variety of user-selected electrical system values and provides control over certain
measurement and data output functions. The IQ 200 Base Module communicates
with the IQ 200 Display Module, providing access to view and reset system, phase,
and min/max values, and providing for viewing and editing of setpoints.
The IQ 200 monitors system and phase values in the following typical system wiring
configurations.
3 Phase
4 Wire 3 Phase 3 Wire 3 Phase 3 or 4 Wire Single Phase 2 or 3 Wire
208Y/120VAC 240VAC 220/380VAC 120/240VAC
480Y/277VAC 480VAC 230/400VAC
600Y/347VAC 600VAC 240/415VAC

TD 17558 Page 3
Effective 3/98
The IQ200 displays the following values:
Values Displayed
System Each Phase Minimum/Maximum
Power Current Currents
Frequency Current Demand Line to Line Voltages
Apparent Power Factor Current Peak Demand Line to Neutral Voltages
Displacement Power Factor Line to Line Voltage System Power
(W, vars, VA)
Watt Hours Line to Neutral Voltage System Frequency
var Hours Watts System Apparent Power
Factor
VA Hours vars System Displacement Power
Factor
Demand (W, var, VA) VA
Peak Demand
(W, var, VA) Apparent Power Factor
DisplacementPower
Factor
The IQ 200 provides the following data outputs:
•INCOM™ communications to provide information to the network master device
(see section 4.9.3 and 4.10.3 for details)
•KYZ Pulse Output proportional to the energy consumed by the system being
monitored (see section 4.9.9 and 4.10.9 for details)

Page 4TD 17558
Effective 3/98
SECTION 2: HARDWARE DESCRIPTION
2.1 GENERAL
This section describes the IQ 200 hardware, its functions and nomenclature, and
lists the IQ 200 specifications. The IQ 200 consists of two components, the Display
Module, figure 2.1, and the Base Module, figure 2.2. Do not attempt to disassemble
or open the case of either the IQ 200 Display Module or the IQ 200 Base Module.
The units contain no user-serviceable components.
Figure 2.1 IQ 200 Display Module Figure 2.2 IQ 200 Base Module
2.1.1 IQ 200 Display Module
The Display Module screen presents system values and functions. The Menu,
up/down Scroll, and Enter buttons allow the operator to view, change, and reset
system parameters. The port for connecting to the IQ 200 Base Module is located
on the bottom side of the IQ 200 Display Module.
2.1.2 IQ 200 Base Module
The IQ 200 Base Module measures system values and provides metering data.
Current and voltage input terminals, power supply terminals, the display port, the
KYZ pulse initiator port, the INCOM™ communications port, and an INCOM™
transmit indicator LED are all located on the rear face of the IQ 200 Base Module.
2.1.3 Installation
The IQ 200 is usually mounted inside an environmentally suitable electrical switch-
gear enclosure. The IQ 200 Display Unit and the IQ 200 Base Module can be
mounted together or separately in a variety of ways, described fully in SECTION 3:
INSTALLATION.

TD 17558 Page 5
Effective 3/98
2.2 OPERATOR PANEL
The Operator Panel is the front face of the
IQ 200 Display Module. It is usually installed
so that it is visible and accessible from the
outside of the panel or door into which it is
mounted.
The Menu, up/down Scroll, and Enter
buttons allow the operator to view, change,
and reset various system parameters: Figure 2.3 Operator Panel
•Display measured system, phase, and min/max values
•View and edit all or individual setpoints
−Password
−INCOM™ network address and baud rate
−System frequency
−Wiring configuration
−CT and PT ratios
−Demand window
−Energy tracking (KYZ pulse output)
•View and reset energy, peak demands, and all or individual minimum and
maximum values.
•Change the display contrast for best viewing
The Operator Panel is an integral part of the IQ 200 Display Module. Do not attempt
to remove it from the IQ 200 Display Module.
2.3 BASE MODULE REAR ACCESS AREA
All wiring connections are made from the rear face of the chassis, shown in
figure 2.4 below.
Figure 2.4 Base Module (Rear Face View)

Page 6TD 17558
Effective 3/98
Note: For sections 2.3.1 through 2.3.4 refer to figure 2.4.
2.3.1 Current and Voltage Inputs
The voltage terminal block is located at the bottom rear of the chassis. It has four
terminals for wiring the phase voltages and the neutral, as shown below. The neutral
terminal must be connected to system neutral or ground depending on system
configuration. All connections must be made in accordance with national and local
requirements and codes.
Phase Voltage Terminal
A VA
B VB
CVC
Neutral NEU
The current transformer terminal block is located at the top rear of the chassis. It
has six terminals, grouped into three pairs: one pair for each phase current
transformer, as shown below.
Phase CT Terminal Pair
AH1A, H2A
BH1B, H2B
CH1C, H2C
2.3.2 Power Supply Input
The IQ 200 power supply input is connected to the PS1 and PS2terminals on the
lower right rear of the Base Module chassis. The IQ 200 requires 90 to 600 VAC or
48 to 250 VDC, and may be wired directly to the monitored system if the voltage is
within range.
2.3.3 Local Display Connection
The supplied Category 5 cable connects to the DISPLAY port located on the middle
right rear of the chassis and to the port on the IQ 200 Display Module. Do not route
the Category 5 cable in the same enclosure or cable tray as 600V system wiring.
2.3.4 INCOM™ Communications
The IQ 200 Electrical Distribution System Meter is an IMPACC (Integrated
Monitoring, Protection, And Control Communications) compatible device. As such, it
can be remotely monitored and functionally modified.
IMPACC is a noise-immune communications system that permits communication to
and from a master computer and the IQ 200 or other devices using a high frequency
carrier signal transmitted over a properly terminated, shielded twisted pair cable.

TD 17558 Page 7
Effective 3/98
Consult TD17513 IMPACC Wiring Specification Base Rules for detailed information
on proper installation and termination of network cable.
The following functions can be performed remotely when the IQ 200 is connected to
an external IMPACC compatible network:
•Display measured system, phase, and min/max values
•View and edit setpoints
−System frequency
−Wiring configuration
−CT and PT ratios
−Demand window
−Energy tracking (KYZ pulse output)
•View and reset energy, peak demands, and all or individual minimum and
maximum values
2.4 EXTERNAL HARDWARE
2.4.1 Current Transformers
The IQ 200 requires at least two user-supplied external instrument class current
transformers with 5 amp secondaries. These transformers must be connected to the
current transformer terminals on the IQ 200 Base Module as detailed in section 3.3.
2.4.2 Potential Transformers
The IQ 200 requires user-supplied potential transformers if line voltage is above 600
volts. These transformers must be connected to the voltage terminals on the IQ 200
Base Module as detailed in section 3.3.
2.4.3 External Fuses
It is recommended that user-supplied fuses be installed as described below to
protect the IQ 200 and related components from damage.
2.4.3.1 IQ 200 Power Supply
External fuses should be installed in the IQ 200 power supply lines, near the IQ 200
Base Module. The fuses should be ½ Amp, 600 volt, BUSS type KTK-R-1/2 Fast
Acting or equivalent.
2.4.3.2 Potential Transformers
External fuses should be installed in the potential transformer lines as specified in
the National Electric Code for the specific application.
2.5 PRODUCT SPECIFICATIONS
Refer to tables 2.1 to 2.5 for all IQ 200 specifications.

Page 8TD 17558
Effective 3/98
2.5.1 Regulatory/Standards Compliance
The IQ 200 meets UL, CUL, and CE requirements.
Table 2.1 IQ 200 Safety Specifications
Safety
IEC 1010-1 (1990) Incl. Amend 1&2 (1995)
EN61010-1 (1993)
CSA C22.2 #1010.1 (1992)
UL3111
EMC
Emissions
FCC Part 15 Class A
CISPR 11 (1990) / EN55011 (1991) Group 1 Class A
Immunity
Electrostatic Discharge
EN61000-4-2 (1995) / EN50082-2 (1995) 4kV CD
8kVAD
Electrical Fast Transient
EN61000-4-4 (1995) / EN50082-2 (1995) 2kVPL
2kVSL
Radiated Immunity
EN61000-4-3 (1997) / EN50082-2 (1995) 10V/m
Conducted Immunity
EN61000-4-6 (1996) / EN50082-2 (1995) 10Vrms
Power Frequency Magnetic Field
EN61000-4-8 (1995) 30 A/m

TD 17558 Page 9
Effective 3/98
Table 2.2 IQ 200 Operating Specifications
Control Power
Input Range 90-600 VAC±10%48-250 VDC±10%
Frequency Range 50/60 Hz —
Burden 180 mA 7 W
Environment Indoor use only
Maximum Operating Altitude 3000 meters
Operating Temperature
Base Unit
Display Module -20° to 50° C
0° to 50° C
Storage Temperature
Base Unit
Display Module -30° to 85° C
-20° to 60° C
Maximum Relative Humidity:
Base Unit
Display Module
(80% for temperatures up to 31° C)
decreasing linearly to 50% at 50° C
decreasing linearly to 50% at 50° C
Current Inputs
InputImpedance
Burden
Overload Withstand
Accuracy Range
5 amp nominal, 10 amp maximum
0.01Ω
0.25 VA
150 Amps ac 1 second
0.5% to 200% of nominal full scale
Voltage Inputs
InputImpedance
Overload Withstand
90 to 600 volts nominal ±10%
2 MΩ
660 VAC continuous
Communication Speeds 1200 Baud ASK
9600 Baud FSK
KYZ
InputVoltage
Maximum Current Rating
Input/OutputIsolationVoltage
240 VAC/300 VDC
96 mA
3750 Vrms
Transient Overvoltage Category OVERVOLTAGE CATEGORY III
Pollution Degree 2 (IEC 664)

Page 10 TD 17558
Effective 3/98
Table 2.3 IQ 200 Metering Accuracy
Parameter Accuracy
Current (<5 amps) ±.5% of Full Scale
Current (>5 amps) ±.5% of Reading
Voltage, line-to-line ±.5% of Full Scale
Voltage, line-to-neutral ±.5% of Full Scale
Watts (<5 amps) ±1% of Full Scale
Watts (>5 amps) ±1% of Reading
vars (<5 amps) ±1% of Full Scale
vars (>5 amps) ±1% of Reading
VA (<5 amps) ±1% of Full Scale
VA (>5 amps) ±1% of Reading
Power Factor ±2% of Full Scale
Frequency ±0.1 Hz
Energy ±1%
Table 2.4 IQ 200 Measurement Ranges
Parameter Max Data Range
Current 0…65,535 amps
Voltage 0…2,097,120 volts
Power
Watts
vars
VA
-1,073,709,057…+1,073,709,056 Watts
-1,073,709,057…+1,073,709,056vars
0…2,147,450,880 VA
Energy
Fwd / Rev Wh
Fwd / Rev varh
Net Wh
Net varh
Net VAh
0…999,999,999 kWh
0…999,999,999 kvarh
-999,999,999…+999,999,999 kWh
-999,999,999…+999,999,999 kvarh
0…999,999,999 kVAh
Power Factor -1.00…+1.00
Frequency 0…255.996 Hz

TD 17558 Page 11
Effective 3/98
Table 2.5 IQ 200 Physical Characteristics
Dimension Display Module BaseModule
Length 1.84 in.(1) 6.74 in.(2)
Height 3.78 in. 3.56 in.(3)
Width 3.78 in. 3.56 in.
Base Unit Terminals
Wire Size #12-22 AWG
ScrewSize #6-32
Torque Rating 9 in.-lbs. Maximum
Distance Between Barriers 0.32 in.
Weight
Display Module 0.60 lbs.
BaseModule 2.35 lbs.
(1) includes 0.50 in. bezel and 0.37 in. ground lug terminal
(2) includes 0.06 in. front face mounting plate and 0.62 in. terminal block
(3)centered on front face mounting plate
2.6 ORDERING INFORMATION
When ordering IQ 200 components, please refer to the Catalog Number listed in
table 2.6.
Table 2.6 IQ 200 Ordering Information
Description Catalog Number
IQ 200 Base Module IQ220TRAN
IQ 200 DisplayModule IQ200D
IQ 200 Base Module and
IQ 200 DisplayModule IQ220
3 foot long Category 5 Cable IQ23CABLE
6 foot long Category 5 Cable IQ26CABLE
10 foot long Category Cable IQ210CABLE
Contents: Base Unit Package
(1) IQ 200 Base Unit
(1) DIN Rail Clip
(4) ½? #10 (10-32) screws
(1) Phoenix Contact
Cable Housing
(1) 3? DIN Rail
(1) L-Bracket
(4) ¼? #8 (8-32) screws
Display Unit Package
(1) IQ 200 Display Unit
(1) 1' shielded Category 5 patch cable
(1) Gasket
(4) Panel Mount Jacks
(4) Thumbscrews

Page 12 TD 17558
Effective 3/98
SECTION 3: INSTALLATION
3.1 INTRODUCTION
The IQ 200 is designed to be installed, operated, and maintained by adequately
trained personnel. These instructions do not cover all details, variations or
combinations of the equipment, its storage, delivery, installation, checkout, safe
operation, or maintenance. Care must be exercised to comply with local, state, and
national regulations, as well as with industry standard safety practices for this class
ofequipment. Refer to figure3.5 through 3.14 forwiring details.
WARNING
A THREE PHASE SWITCH OR CIRCUIT BREAKER SHOULD BE IN CLOSE
PROXIMITY TO THE IQ200 MOUNTING LOCATION AND MARKED AS THE
DISCONNECTING DEVICE FOR THE EQUIPMENT.
WARNING
TURN OFF AND LOCK OUT POWER SUPPLYING THE PANELBOARD OR
SWITCHGEAR IN WHICH THE IQ200 IS BEINGINSTALLED. INJURY TO
PERSONNEL OR DAMAGE TO EQUIPMENT CAN RESULT.
3.2 PANEL PREPARATION
It is recommended that the IQ 200 be mounted in an electrical switchgear enclosure
that is suitable for its environment. The IQ 200 Display and IQ 200Base Modules
maybemounted together or separately. TheIQ 200 is designed with flexibility in
mind.Whileit is recommended that theIQ 200 Display Module be door- or panel-
mounted,the Base Modulemay be attachedtothe IQ 200 Display Module; mounted
remotely using the supplied DIN rail and clip, or L-bracket; or mounted directly to
panel or floor. For floor or panel mounting, a #10 (10-32) or #12 (12-28) screw is
recommended.
In all instances where the IQ 200 Base Module is mounted remotely, the IQ 200
Display Module Chassis must be connected to earth ground.
Before installing the IQ 200, refer to dimensions listed in table 2.5 and allow
adequate room for wiring of and access to the IQ 200 Base Module terminals and
connectors.

TD 17558 Page 13
Effective 3/98
3.2.1 Mounting the IQ200 Modules as a Single Unit
Using the screws provided, attach the supplied DIN rail to the back of the IQ 200
Display.Usethe screws provided with theIQ 200 Base Module to attach the
suppliedDIN cliptothefrontfaceofthe IQ 200 Base Module.
Cut a ¼ DIN (92mm x 92mm) access cutout in the switchgear door or other panel
wherethe IQ 200 is to be mounted as shown in figure 3.1. Install the IQ 200 Display
Module as shown in figure 3.1, following these steps:
•Install the supplied gasket
when using in NEMA 12
applications.
•Slide the supplied gasket over
the rear of the IQ 200Display
Module until it is flush with the
rear of the outer bezel.
•InserttheIQ 200 Display
Module with gasket installed
intothe cutout.
•Slide the 4 supplied locking
barsinto the 4slots in thetop,
bottom, and sides at the rear of
theIQ 200 Display Module
Figure 3.1 Securing the IQ 200 Display
Module
•Insert and tighten the supplied thumbscrews to secure the IQ 200 Display Module
in place.
•ConnecttheIQ 200 Base Module to the IQ 200 Display Module using the DIN rail
andclip,as shown in figure 3.2.
ConnecttheIQ 200 Display
ModuletotheIQ 200 Base
Module by inserting one end of the
1 foot long Category 5 cable into
theport on the IQ 200 Display
Module, and the other end into the
DISPLAYport on the IQ 200 Base
Module. Do not route the Category
5 cable in the same enclosure or
cable tray as 600V system wiring.
Proceed to section 3.3, Wiring.
Figure 3.2 Mounting the IQ200 Base
Module to the IQ200 Display Module
3.2.2 Mounting the IQ200 Display and Base Modules Separately
In allinstances where the IQ 200Base Moduleismounted remotely,the IQ 200
Display Module Chassis must be connected to earth ground.