Eaton MEMSHIELD3 Manual

IMPORTANTNOTES
1. This product should be installed, commissioned and
maintained by or under the supervision of a competent
electrician in accordancewithcurrent electrical engineering
Codes of Practice, Regulations forthe Electrical equipment
of Buildings (BS7671), CDM2007 - Construction (Design
and Management) Regulations 2007, HSG150 - Health and
Safety in Construction, Statutory requirements and any
Specific instruction issued by the Company.
2. Aftercompleting the installation and testing of this product it
is essential that this leaflet is drawnto the attention of the
person responsible for its futureoperation and maintenance,
and is at all times available for ready reference.
3. These notes assume throughout that the product is
disconnected fromthe supply. It is essential that this is done
before any workiscarried out.
4. When carrying out insulation resistance testing, ensure the
meter voltage fuses are removed.
MEMSHIELD3SMARTMETERSPLITLOADDISTRIBUTIONBOARD
Instruction leaflet LT1184 (03/21)
DrawnasEBMSL642MPMB
kWh
W
Meteroperating instructionscan
be found on leafletprovided with
digitalmeter.
Please ensure that meter
instructionsare available for
continueduse of the product.
METER
LOAD2
LOAD1
These Distribution Boards are designed only for
usewithMCB’s and RCBO’s as listed in the current
Memshield 3catalogue.
Failure to complywillresult in invalidwarrantyand
certification.
CAUTION
Do not fit SP & SN, or 4 pole MCB’s in TP
type B board
Ensure both neutral
shieldsare fitted
after installation
Tighten to
15Nm Earth bolt
Tightento
15Nm

FITTINGANMCB/RCBO
When fitting an RCBO, trim RCBO ‘N’ cable to length
and connect to ‘N’ busbar terminal.
Connect load live/neutral cable direct to RCBO.
TIGHTEN TERMINAL SCREWS TO2.4Nm.
All unused ways
must be fitted with
a blanking module,
assembled and
fitted in gangs of 3.
Before fitting
to busbar
ensure MCB
terminal is
fully open
IMPORTANT:
Orientate MCB clipnext
to busbar stack
Locate and
tighten terminal
screws to2.4Nm
Clip fit
Remove thin area (shaded)
inside shield toallow
link to be fitted
FITTINGSINGLEPHASE?
Ensure both
neutral shields
are fitted after
installation
W ARN IN G
SHORTINGBARFITTED
Fit cover withlabel
Single
phasing
link
Tighten
terminal
screws to
15Nm

M6 Keyhole
fixing
440
83
AB
270
For extrasecurity fit
padlock List No. PD2
FITTINGDOORLOCKEMDL&EMPL
Remove
Plastic
Knob
Insert Lock into
hole tighten
back nut
NEUTRALLINKDISCONNECTION
Incoming
neutral link
DIMENSIONS(mm) 326
10 FITTINGEMBL2
130
100
FUNCTIONAL (CLEAN)EARTH
For Functional (Clean) Earth requirement:
Modify assembly using stand-offs as shown
CAT.No.
A B
EBMSL642MPMB
1130 946
EBMSL862MPMB
1236 1052
EBMSL1082MPMB
1342 1158
EBMSL14102MPMB
1501 1317
Tightento
3.8Nm
Tightento
5Nm
Earth/Neutral
terminal screws
Tighten to:
M4 - 1.2Nm
M6 - 2.5Nm
IMPORTANT
Replace ‘N’ link and
retighten after test
M6 Earth terminal
screws Tightento
2.5Nm

INSTALLATION DATE:
CONTRACTOR:
FED FROM:
INCOMING CABLE SIZE:
LOAD 2
LEFTANDRIGHTHAND
OUTGOINGCIRCUITS
LOAD 1
LEFTANDRIGHTHAND
OUTGOINGCIRCUITS
L1
L2
L3
L1
L2
L3
L1
L2
L3
L1
L2
L3
L1
L2
L3
L1
L2
L3
L1
L2
L3
L1
L2
L3
L1
L2
L3
L1
L2
L3
L1
L2
L3
L1
L2
L3
L1
L2
L3
L1
L2
L3
L1
L2
L3
L1
L2
L3
L1
L2
L3
L1
L2
L3
L1
L2
L3
L1
L2
L3
L1
L2
L3
L1
L2
L3
Warning -
Intellectual Property Rights
Eaton wishes to make it clear that it owns intellectual property rights in the
product which it manufactures (whether or not listed in this leaflet) and that it
will take legal action against any party found to be manufacturing, using, or
selling any article which infringes the company’s intellectual property. All
marks in this document identified with an R symbol or aTM symbol adjacent to
the mark are trademarks of Eaton.
C 2019 EatonElectric Limited.
All rights reserved.
The use to which thisproductisput and itsplace of installationis outsideour control.
Particular care shouldthereforebe takento followthe instructionsgiven here and to
ensure their continuedavailabilityin conjunctionwiththeuse of the product.
No responsibility can be accepted by us if these instructionsare disregarded.
Further copiesof theseinstructionsand informationconcerningtheinstallation and
proper use of this product can be obtained by contacting the:
TechnicalServicesDepartment
Eaton ElectricLimited, Middleton, Manchester, M24 1GQ.
Tel:[phone],
email: [e-mail]