Eaton BiWire Ultra User manual

0359-CPR-00419
2. Connection details
1a. Mounting base (IP21C) 1b. Mounting base (IP66C)
Table 1. Specification
Technical data Effective September 2014
FXN009SB/EF009SB
FXN009SBWP/EF009SBWP
FXN009/EF009
FXN009WP/EF009WP
Wall sounder/beacon
Wall sounder
Supply voltage (BiWire alarm) 25.5~35 Vdc
Supply voltage (BiWire standby) 18~25.5 Vdc
Supply voltage (conventional) 18~35 Vdc
Cable size/type 0.5~2.5mm/FIRETUF, FP200
or MICC
Standby current (BiWire mode) <15μA
Current (high volume) Sdr only = 4.7mA, AV = 11mA
Current (low volume) Sdr only = 2.6mA, AV = 8.7mA
Sound output (high volume) 99 +/- 3dB(A) : All tones
Sound output (low volume) 89 +/- 3dB(A) : All tones
Operating temperature -25 to +70ºC (93% ± 3%RH)
Material ABS FR plastic
Environmental category Type A= IP21C/ Type B= IP66
Tones 3, See section 3
Flash rate 0.5Hz (N/A to FXN009(WP), EF009(WP))
Flash on period 60ms (N/A to FXN009(WP), EF009(WP))
Feature Value Feature Value
BiWire Ultra range:
Wall sounder/beacon IP66
Wall sounder IP66
50
50
60
(i) Drill required holes for
cable gland fixing.
(iii) Fix to mounting surface
using two suitable screws.
(ii) Drill out the required
fixing holes.
Drill position for rear
cable entry
Drill position for
glands
50 (IP33)
50 (IP33)
75 (IP66)
97 (IP66)
62 (IP33)
(i) Drill required holes for cable gland fixing (top or bottom)
and ensure cables are correctly sealed for IP66 integrity.
(ii) Fix to mounting surface using four suitable screws.
Drill position
for glands
Use these four holes
to ensure IP66 integrity
1 2 3 4 5
1
On
Off
3. Switch position meaning
1, Sounder on/off (AV version only)
2, Volume high (Off)/low (On)
3, Tones
4, Tones
5, Mode: On = BiWire, Off = Conventional
Continuous: 3=On, 4=On (984Hz)
Bell: 3=On, 4=Off (1440Hz)
Alternating: 3=Off, 4=On (644/984Hz)
{
OUT IN
SCREEN ZONE OUT ZONE IN
+VE -VE +VE -VE
ZONE IN
ZONE OUT
Screen must be continuous along entire length of loop.
Compliance EN54-3; EN54-23:2010
14
(Conventional compatible)
25-12766-E
2
Note
All products meet minimum requirements of IP33C in
accordance with EN54-3.
www.acornfiresecurity.com
www.acornfiresecurity.com

6a. Sounder assembly (WP)
5b. Dimensions5a. Sounder assembly
106
91
106
100110
110
(i) Clip sounder onto base.
(ii) Ensure cables do not
put stress on the PCB.
Key
Holes
To unlock use
key provided
(i) Location ribs must align on base and sounder.
(ii) Ensure cables do not
put stress on the PCB.
(iii) Bolt sounder to base.
Ribs
6b. Dimensions (WP)
4. VAD coverage area
Cross section
view (metres)
Product
3.2m
3.2m
Technical data
Effective September 2014
FXN009SB/EF009SB
FXN009SBWP/EF009SBWP
FXN009/EF009
FXN009WP/EF009WP
Wall mounted 3D
view
Cross Section
plane
www.acornfiresecurity.com
www.acornfiresecurity.com