Indiana Furniture Square One 17-10 User manual

800.422.5727 www.IndianaFurniture.com
Square One
Assembly Instructions
17-10
Tools Needed:
Components: Model Description 17-10
Quantity
17-2424BL Single Block, 24"x24“
(4 Bolts & Nuts Included) 36
17-17548EC End Cap, 48" 2
(used horizontally)
17-17597EC End Cap, 97-3/4" 4
(used vertically)
17-17524CP Corner Post, 24" 2
(used horizontally)
17-17548CP Corner Post, 48” 2
(used horizontally)
17-17548TCB T-Connector Beam, 48" 1
17-17596TCB T-Connector Beam, 96" 2
17-LEVKIT Leveler Kit, 2 Levelers 8
17-12MMBOLTKIT 12mm Bolt Kit, qty 8 1
A
A
B
B
B
C
C
D
C
E
D
F
E
4x8x8
17-10 Page 1 of 3
D
F
Drill 5mm & 4mm
Allen Keys
Box Level Tape
Measure
Ladder 2 to 3
Installers
6mm Allen Key
Driver Bit
NOTE: Anchoring to floor or wall may require additional tools and hardware. See note at end of instructions.

800.422.5727 www.IndianaFurniture.com
Square One
Assembly Instructions
17-10
17-10 Page 2 of 3
4x8x8
Begin by building the configuration 1 block high. To
establish the configuration footprint.
Align the holes in blocks and connect with 2, 80mm
bolts and 2, 17mm nuts.
Fasten the bolt and nut together but do not
over tighten because you will want to align
and firmly tighten upon final setup.
In the bottom row of blocks install the levelers. Use
the 6mm Allen Key Driver Bit to install the threaded
insert into the bottom holes of the block.
It is important that the threaded insert is
installed as close to perpendicular as possible.
Thread the leveler into the insert. Then thread a
17mm nut onto the top of the leveler.
Connect the 97-3/4” T-Connectors to the wall
sections using the 60mm bolts and the threaded
inserts in the post.
Using a box level to check level, adjust the levelers
on the configuration so they are all touching the
floor.
Install the rest of the blocks using the 80mm bolts
and 17mm nuts until the configuration is built.
1
2
3
4
Box Level T-Connector
Adjust
Levelers
6
5
6
7
17mm nut
Threaded
Insert
Leveler
4
80mm bolt
60mm bolt
17mm nut
Cap, Post, or Beam
2
5
2

800.422.5727 www.IndianaFurniture.com
T-Connector
Corner Post
End Cap
Square One
Assembly Instructions
17-10
17-10 Page 3 of 3
4x8x8
Install the 97-3/4” vertical End Caps using the 60mm
bolts.
Using a ladder and an assistant, install the 48” T-
Connector, 24” & 48” Corner Posts on the top of the unit
using the 60mm bolts.
Fasten 2 blocks together with a 24” end cap on one side
and attach the assembly to the top of the configuration.
Install 12mm bolts into any unused inserts in the corner
posts
Once everything is attached, go back and align
components. This may require loosening bolts and nuts
to align. Once adjusted to satisfaction, tighten hardware
to a secure fit.
Your configuration is complete.
If adding Acoustical or Tackable Panels, Acrylic Inserts,
Dry Erase Boards, or TV Mounts, see individual
instructions for installation.
Wall / Floor Anchoring:
Additional support is required for configurations that are
not free standing. Anchoring to the floor, wall, ceiling,
and other furniture will require additional tools and
hardware, not provided by Indiana Furniture. The
installer is responsible for sourcing hardware and for the
installation of support per building conditions.
8
98
10
11
9
12
13
13
10
97-3/4”