eDecks Rosedene User manual

Contents
Don’t forget to check your work with a level as you go! Page 1 of 8
PARTS INCLUDED IN YOUR KIT
www.eDecks.co.uk
3 x 1400mm
1 x 1400mm notched for legs
6 x 1210mm
2 x 915mm
2 x 560mm Chamfered Arm Rests
4 x 560mm
2 x 470mm
2 x 510mm Angled Cut Back Supports
60 x 80mm Screws
All images are for illustration only, Please see individual item listings for actual item specifications
Garden Bench Fitting Instructions

Step 1
Don’t forget to check your work with a level as you go! Page 2 of 8
Start by joining the 915mm back legs (A) and
560mm front legs (D) together by screwing into the
470mm arm support (B) with 2 x 80mm screws from
the front & 2 x 80mm screws from the back, as shown
in the diagram.
Then screw into place (C) so it is 1ft off the ground
and sits flush to the front of (A) and back of (D) again
using 2 x 80mm screws front and back.
Repeat these steps for the opposite side so it mirrors
2 x 80mm
1 ft off the ground Front
Back
Inside
Outside
2 x 80mm
2 x 80mm
2 x 80mm
www.eDecks.co.uk
All images are for illustration only, Please see individual item listings for actual item specifications
Garden Bench Fitting Instructions
A
D
B
C
A
B
C
D
560mm

Step 2
Don’t forget to check your work with a level as you go! Page 3 of 8
INSTALL ANGLED BACK SUPPORTS
Place the angled support (A) so that it sits
30mm from the back of the seat support.
Fix this into position using 2 x 80mm screws
top and bottom as shown in diagram.
www.eDecks.co.uk
All images are for illustration only, Please see individual item listings for actual item specifications
Garden Bench Fitting Instructions
Back
Inside
2 x 80mm
2 x 80mm
A
30mm

Screw a 1400mm support to the front of the
frame, using 2 x 80mm screw at each end as
shown in diagram below.
INSTALL THE BENCH FRONT SUPPORT
Step 3
Don’t forget to check your work with a level as you go! Page 4 of 8
www.eDecks.co.uk
All images are for illustration only, Please see individual item listings for actual item specifications
Garden Bench Fitting Instructions
Front
1 ft off the ground

Screw a1400mm support to the top, using 1
x 80mm screw at each end into the back
legs (A) and 2 x 80mm screws into the
angled back rest supports (B) as shown in
diagram below.
INSTALL THE BENCH TOP SUPPORT
Step 4
Don’t forget to check your work with a level as you go! Page 5 of 8
www.eDecks.co.uk
All images are for illustration only, Please see individual item listings for actual item specifications
Garden Bench Fitting Instructions
A B

Position the 1400mm piece with cuts outs
for the legs at the front of the seat (A) secure
with 2 x 80mm screws at each end as shown
in diagram below.
Then add the 3 x 1210mm slats to the seat
area with a gap of 1” between each slat t,
secure with 2 x 80mm screws at each end as
shown below (B)
INSTALLING THE SEAT SLATS
Step 5
Don’t forget to check your work with a level as you go! Page 6 of 8
www.eDecks.co.uk
All images are for illustration only, Please see individual item listings for actual item specifications
Garden Bench Fitting Instructions
A
B

Evenly space the 3 remaining 1210mm slats
(A) on the angled part of the frame using 2 x
80mm screws at each end
Fix the last piece of 1400mm to the top of the
backrest so it is flush with top piece of
1400mm installed in the previous step.Again
using 2 x 80mm screws in each end (B)
INSTALLING THE BACK REST
Step 6
Don’t forget to check your work with a level as you go! Page 7 of 8
www.eDecks.co.uk
All images are for illustration only, Please see individual item listings for actual item specifications
Garden Bench Fitting Instructions
A
B

Lastly screw the 2 arm rests into
position (A) by screwing up through
the framing underneath with 2 x
80mm screws in each end of the
armrest.
Finish
Don’t forget to check your work with a level as you go! Page 8 of 8
All images are for illustration only, Please see individual item listings for actual item specifications
Garden Bench Fitting Instructions
A
A
Screw up
through the
frame into
the arm rests