Eden HA2000PB User manual

Panic Button (HA2000PB)
The Fixed Panic Button is used to activate the
panic or medical alarm.
PANIC
BUTTON
Pressing
this button
for 3
seconds will
trigger the
panic alarm
regardless of whether the system is
Armed or Disarmed.
Led Indicator
When the Red Panic button is
pressed, the TX LED will flash to
indicate the HA2000PB has
successfully sent out a signal to the
Control Panel.


B
Ba at tt te er ry y
The Fixed Panic Button uses one 12V
35mAh alkaline battery as its power
source. The battery is good for
approximately 2,600 signal
transmissions before it needs
changing.
HA2000PB can also detect the low
battery status. The low battery
signal will be sent to the Control
Panel along with regular signal
transmission for the Control Panel to
display the status accordingly.


G
Ge et tt ti in ng g S St ta ar rt te ed d
Remove the screw to separate the
top cover from the base.
Insert the battery with negative of
the battery on the spring side.
Place the top case over the base.
Put the Control Panel into “Device
+/-“ menu and ten select “Add
Device” menu.
Press any buttons on the
HA2000PB.
Press “OK” on the Control Panel
and follows its settings to complete
the Learning-In process. Refer to
the operation manual of your
control panel under the section of
“Device +/-“ to complete the
learn-in process.
The Learning-In process is now
completed.
After the HA2000NS is learnt-in,
put the Control Panel into “Walk
Test” mode, hold the Night Switch
HA2000PB in the desired location,
and press the Test button to
confirm this location is within signal
range of the Control Panel.
When you are satisfied that the
HA2000PB work in the chosen
location, you can proceed with
installation.


M
Mo ou un nt ti in ng g t th he e H HA A2 20 00 00 0P PB B
There are two ways to mount the
HA2000PB by either Self-adhesive
installation or Screw mounting.
Self adhesive installation
1. Clean the surface with a
suitable degreaser.
2. Remove the protective
covering from one side of
the double-sided adhesive
pad and firmly apply to the
back of the device.
3. Next remove the other cover
and firmly press the item
onto the desired location.
<
< N NO OT TE E > >
Do not use the adhesive pad
method of installation on a
surface with peeling or
cracked paint, or on a rough
surface.
Screw Mounting
The base has two knockouts, where
the plastic is thinner for mounting
purpose. To mount the HA2000PB:
1. Remove the screw to
separate the top cover from
the base.
2. Break through the knockouts
on the base.
3. Using the holes as a
template, drill two holes and
insert the wall plug.
4. Screw the base into the wall
plug.
5. Screw the top cover back on
to its base
1
2


 S Sp pe ec ci if fi ic ca at ti io on ns s: :
Common Technical Specification:
Radio frequency: 868.6375MHz
+-2.5ppm
Modulation/ Demodulation: Narrow
band FM @ 15KHz bandwidth with
VCTCXO (Temperature
compensated Crystal)
Sensitivity: >105dbm @S/N +20db
Transmission power: E.I.R.P.
-8dbm +-3db
Operation range: 300 meters in
open space
Code combinations: 16 777 216
codes
Temperature range:-20°C +45°C
Humidity: up to 90%
HA2000PB
1 programmable function : Panic
(Distress) or Medical.
Weak battery detection
Power : Alkaline 12V
Battery life : 54 months assuming 4
transmissions per day
Dimensions: 72mm x 43mm x
15mm
Weight: 40g


G
Gu ua ar ra an nt ty y
This product is guarantee 4 years except
the batteries. The first year is by standard
exchange. The 3 years left, the guarantee is
for parts and labours.
Please contact, the technical line, following
your country, to confirm the default and the
guarantee process.
France:
Eden: 0825 560 650
Web site: www.eden.fr
Holland:
Elro: 0900 208 8888
Web site: www.elro-nl.com
Belgium:
Dutch speaking
Elro: 070 2330031
French Speaking
Eden: 0033 825 560 650
Germany:
Elro: 0049 17755 24123
England:
Byron: 0845 230 1231
Website: www.chbyron.com