Edge-Core CSR300/AS7315-30X User manual

– 1 –
Quick Start Guide
1. QSFP28 Port LEDs:
Blue — 100G
Green — 40G
2. QSFP28 Breakout LEDs:
White — 2 x 50G
Blue — 4 x 25G
Green — 4 x 10G
6. System LEDs:
LOC — Blinking Blue (OK)
DIAG — Green (OK), Orange (fault detected)
PSU1/2 — Green (OK), Orange (fault)
FAN — Green (OK), Orange (fault)
ALRM — Green (OK), Red (alarm)
7. PPS/ToD LED: Blinking Green (1PPS input)
8. RJ-45 Management Port LEDs: Left (link), Right (activity)
2
6
5
3. SFP28 Port LEDs: Blue (25G),
Green (10G), Cyan (1G)
4. SFP+ Port LEDs: Green (10G),
Amber (1G)
5. 1G RJ-45 Port LEDs:
Left (link), Right (activity)
3
87
4
1
5
E112021-CS-R01
150200002459A
Cell Site Gateway
CSR300/AS7315-30X
1.
CSR300/AS7315-30X (includes 2 PSUs and 1 fan tray)
2. Rack Mounting Kit—2 brackets and 8 screws
3. Grounding kit—grounding lug, 2 screws, and 2 washers
4. Ring lugs (x4) (included with DC PSUs only)
5. (Optional) AC power cord
6. Documentation—Quick Start Guide (this document) and Safety
and Regulatory Information
Fan Tray
Replacement
1. Press the
release latch
in the fan tray
handle.
PSU
Replacement
Fan Tray Replacement
1. Press the fan tray’s release
latch.
2. Pull out to remove the tray.
3. Install replacement tray with
matching airflow direction.
PSU Replacement
1. Remove the power cord.
2. Press the release latch and
remove the PSU.
3. Install replacement PSU.
Package Contents
Overview
FRU Replacement
1
Status LEDs
1. 2 x DC or AC PSUs
2. 2 x 100G QSFP28 ports
3. Product tag
4. 8 x 25G SFP28 ports
5. USB storage port
6. Reset button
7. 16 x 10G SFP+ ports
8. 4 x 1G RJ-45 ports
9. PPS/ToD RJ-45 timing port
10. Management I/O: 1000BASE-T RJ-45, RJ-45 console
11. Fan tray
12. Grounding screw
1
10
36
2 4 8
5
11
7
12
9
www.edge-core.com
*150200002459A_R01*
2 3 4 5 6
Fan Tray
Replacement
1. Press the
release latch
in the fan tray
handle.
PSU
Replacement
2. Right-to-Left Airflow
Install a right-to-left airflow fan tray
(indicated by the arrow on the
panel).
1. Left-to-Right Airflow
Remove the left-to-right airflow
fan tray (indicated by the arrow
on the panel).
Airflow Reversal

Quick Start Guide
– 2 –
Mount the Router in an EIA-310 Rack
1. For 300mm-deep rack: Using the four front screw holes, attach
each of the brackets to the router with four of the included bracket
screws.
2. For 280mm-deep rack: Using the four recessed screw holes, attach
each of the brackets to the router with four of the included bracket
screws.
3. Use the screws and cage/clip nuts supplied with the rack to
secure the router in the rack.
Ground the Router
Verify Rack Ground
Ensure the rack is properly grounded and in compliance with
international and local standards. Verify that there is a good electrical
connection to the grounding point on the rack (no paint or isolating
surface treatment).
Attach Grounding Wire
Attach the grounding wire (#6 AWG/16 mm2) to the grounding point on
the router’s rear panel or side panel. Then connect the other end of the
wire to rack ground.
Connect Power
a. AC Power
Install one or two AC PSUs in the router, if they are not already installed
in the factory. Then connect an external AC power source to the PSUs.
b. DC Power
Install one or two DC PSUs (part number CRXT-T0T12B only) in the
router, if they are not already installed in the factory.
Connect an external DC power source to the PSUs. Or, connect to a no-
tolerance DC mains supply with a UL/CSA-approved circuit breaker
rated at 16 A.
Warning: For a safe and reliable installation, use only
the accessories and screws provided with the device. Use
of other accessories and screws could result in damage to
the unit. Any damages incurred by using unapproved
accessories are not covered by the warranty.
Avertissement: Pour une installation sûre et fiable,
utilisez uniquement les accessoires et les vis fournies avec
l’appareil. L’utilisation d’autres accessoires et vis pourrait
endommager l’appareil. Les dommages causés par
l’utilisation d’accessoires non approuvés ne sont pas
couverts par la garantie.
Caution: The device must be installed in a restricted-access
location.
Attention: le périphérique doit être installé dans un
emplacement à accès restreint.
Note: The router has the Open Network Install Environment
(ONIE) software installer preloaded, but no router software
image. Information about compatible router software can be
found at www.edge-core.com.
Note: The drawings in this document are for illustration only
and may not match your particular model.
1
12
3
Caution: The earth connection must not be removed unless
all supply connections have been disconnected.
Attention: Le raccordement à la terre ne doit pas être retiré
sauf si toutes les connexions d’alimentation ont été
débranchées.
2
Rear Panel Side Panel
3
Installation

Quick Start Guide
– 3 –
1. Connect the ground wire / protective earth.
2. Connect the -36 – -72 VDC wire.
3. Connect the DC return wire.
Make Network Connections
QSFP28/SFP28/SFP+ Ports
Install transceivers and then connect fiber optic cabling to the transceiver
ports. Alternatively, connect AOC/DAC cables directly to the QSFP28/
SFP28/SFP+ slots.
The following transceivers are supported in the QSFP28 ports:
■100GBASE-SR4
■100GBASE-LR4
■100GBASE-ER4
The following transceivers are supported in the SFP28 ports:
■25GBASE-SR
■25GBASE-LR
The following transceivers are supported in the SFP+ ports:
■10GBASE-SR
■10GBASE-LR
■10GBASE-ER
■10GBASE-ZR
RJ-45 Ports
For the 1G RJ-45 ports, connect 100-ohm Category 5, 5e or better
twisted-pair cable.
Connect Timing Port
RJ-45 PPS/ToD
Use a Cat. 5e or better twisted-pair cable to connect the 1-pulse-per-
second (1PPS) and Time of Day (ToD) to other synchronized devices.
Make Management Connections
MGMT RJ-45 Port
Connect Category 5, 5e or better twisted-pair cable.
RJ-45 Console Port
Use the included RJ-45-to-DB-9 null-modem console cable to connect to
a PC running terminal emulator software. Use a USB-to-male DB-9
adapter cable (not included) for connections to PCs that do not have a
DB-9 serial port.
Configure the serial connection: 115200 bps, 8 characters, no parity,
one stop bit, 8 data bits, and no flow control.
Console cable pinouts and wiring:
Caution: Before connecting power supply cables to the router,
ensure that power to the feed lines is turned off at the supply
circuit breaker or disconnected from the power bus.
Attention: Avant de connecter les câbles d’alimentation au
routeur, assurez-vous que l’alimentation des lignes
d’alimentation est coupée au niveau du disjoncteur
d’alimentation ou déconnectée du bus d’alimentation.
Caution: Use a UL/IEC/EN 60950-1 and/or 62368-1
certified power supply to connect to a DC converter, and a #14
AWG/1.5 mm2(for 36 VDC to 72 VDC PSU) wire to connect to
a DC PSU.
Attention: Utilisez une alimentation certifiée UL/IEC/EN
60950-1 et/ou 62368-1 pour le connecter à un convertisseur
CC et un câble AWG #14/1.5 mm2(pour 36 VDC à 72 VDC)
pour vous connecter à une alimentation CC.
Caution: All DC power connections should be performed by
a qualified professional.
Attention: Toutes les connexions d’alimentation CC doivent
être effectuées par un professionnel qualifié.
Note: It is suggested to use the following for DC power:
One UL 1015 AWG#10-14 stranded wire, 2m maximum
(36VDC-72VDC: Input+)
One UL 1015 AWG#10-14 stranded wire, 2m maximum (VDC
return: Input-)
One UL 1015 AWG#10-14 stranded wire, 2m maximum,
(green/yellow) green with yellow stripe (PE)
Note: The DC terminal screws should be tightened to a
torque of 7 in-lbs maximum.
1
3
2
4
Router’s RJ-45 Console Null Modem PC’s 9-Pin DTE Port
6 RXD (receive data) <---------------- 3 TXD (transmit data)
3 TXD (transmit data) ----------------> 2 RXD (receive data)
4,5 SGND (signal ground) ------------------ 5 SGND (signal ground)
5
6

Quick Start Guide
– 4 –
Hardware Specifications
Router Chassis
Size (WxDxH) 440 x 300 x 44 mm (17.32 x 11.81 x 1.73 in.)
Weight 5.35 kg (11.79 lb), with two installed PSUs
Temperature Operating: -40° C to 65° C (-40° F to 149° F)
Transportation: -40° C to 70° C (-40° F to 158° F)
Storage: -40° C to 70° C (-40° F to 158° F)
Humidity Operating: 5% to 95% (non-condensing)
Power
Capacity
290 Watts maximum
48 VDC PSU
Power Rating -48 VDC, 300 Watts
DC Input -36 V – -72 V, 10 A
AC PSU
AC Input 100–240 VAC, 50/60 Hz, 5 A maximum
Regulatory Compliances
Emissions EN 55032:2015+AC:2016, Class A
EN 61000-3-2:2014, Class A
EN 61000-3-3:2013
EN 300 386 V1.6.1
EN 301 489-1 V2.1.1
EN 301 489-19 V2.1.0
EN 303 413 V1.1.1
FCC Title 47, Part 15, Subpart B, Class A
Radio Equipment Directive 2014/53/EU
VCCI-CISPR 32:2016, Class A
BSMI Class A, CNS 13438
CCC GB 9254-2008, Class A
Immunity EN 55035:2017
EN 55024:2010+A1:2015
IEC 61000-4-2/3/4/5/6/8/11
Environmental Storage:
◆ETSI EN 300 019-1-1 Class 1.1
◆Temperature: -40° C to 70° C (-40° F to 158° F)
Transportation:
◆ETSI EN 300 019-1-2 Class 2.3
◆Temperature: -40° C to 70° C (-40° F to 158° F)
Operating Conditions:
◆ETSI EN 300 019-1-3 Class 3.2
◆Temperature: -40° C to 65° C (-40° F to 149° F)
◆Relative Humidity: 5% to 95%
Safety UL (CSA 22.2 No 62368-1 & UL 62368-1)
CB (IEC/EN 60950-1 & IEC/EN 62368-1)
BSMI CNS14336-1
CCC GB4943.1-2011