Edwards VolumeView EV1000 User manual

System Setup
VolumeView sensor
VolumeView femoral arterial catheter
VolumeView thermistor manifold
Edwards Oximetry Central Venous Catheter
TruWave pressure transducer
Oximetry cable
1
2
3
4
5
6
1
2
3
4
5
6
VolumeView Set EV1000 Clinical Platform
Setup Guide
For professional use. See instructions for use for full prescribing
information, including indications, contraindications, warnings,
precautions and adverse events.
Edwards Lifesciences devices placed on the European market
meeting the essential requirements referred to in Article 3 of
the Medical Device Directive 93/42/EEC bear the CE marking of
conformity.
Edwards, Edwards Lifesciences, the stylized E logo,
EV1000, TruWave, and VolumeView are trademarks
of Edwards Lifesciences Corporation.
© 2018 Edwards Lifesciences Corporation.
All rights reserved. ENP509/11-18/CC
Edwards Lifesciences • Route de l’Etraz 70,
1260 Nyon, Switzerland • edwards.com

EV1000 Clinical Platform Startup with the VolumeView Set
Before startup, please ensure monitor, cables and patient cables
are all connected.
1. Turn on monitor and databox. System self-test starts.
2. Enter new patient data OR continue with existing patient.
3. Set up and prime VolumeView sensor and TruWave CVP
transducer and connect to databox.
4. Ensure the sensor and transducer
are level to patient’s phlebostatic
axis and zero transducers on monitor
using Clinical Actions button.
5. Choose continuous parameters,
and define alarms/target range.
6. Start transpulmonary thermodilution -
inject bolus and review and edit boluses
results.
7. Monitor patient in real time with one of the six available
screens.
Thermodilution Bolus - VolumeView Set
1. Insert the VolumeView femoral arterial catheter
according to the directions for use.
2. Insert a Central Venous Catheter (CVC) (if using the Edwards
oxymetry CVC , refer to the Edwards oxymetry CVC setup
guide).
3. Ensure the TruWave central venous pressure
transducer and VolumeView sensor are primed
and then connected to the EV1000 databox.
4. Ensure the sensor and transducer
are level to patient’s phlebostatic
axis and zero transducers on monitor
using Clinical Actions button.
5. Connect the VolumeView sensor
to the VolumeView femoral arterial
catheter and confirm the appropriate
waveforms and pressures are displayed.
6. Connect the databox thermistor cable to the VolumeView
femoral arterial thermistor and confirm appropriate
temperature on the EV1000 monitor.
7. Prime the VolumeView set manifold, removing all air.
Connect the TruWave central venous pressure transducer
to the VolumeView manifold and then connect it to
the central venous catheter and
confirm the appropriate waveform
and pressure are displayed.
8. Connect the in-line injectate
thermistor probe to the VolumeView
manifold.
9. Connect a pre-chilled syringe
with (15 or 20 ml) normal saline to
the VolumeView manifold valve/port.
10. Touch the Clinical Actions button
and then touch the Thermodilution
button to start the TPTD procedure.
11. Select the desired injectate volume on
the keypad (prefer 15 or 20 ml).
12. Select Lung Resection, if appropriate,
as well as the descriptor (for example
RUL = right upper lobectomy).
13. Select Parameters, to choose indexed or
non-indexed parameter.
14. Touch Start Set.
15. Wait is highlighted until the thermal baseline is reached.
16. When Inject is highlighted, use a rapid, smooth, continuous
method to inject the cold solution with the volume amount
previously selected.
17. Observe the calculation.
18. Repeat steps 14 and 15.
19. Touch review to edit the series of boluses.
20. Touch Accept.
thermistor probe to the VolumeView
the VolumeView manifold valve/port.
87
9