Elba EISF-G2601(BK) User manual

1
INDUSTRIAL STAND FAN
MODEL: EISF-G2601(BK)
Please read this manual carefully
before operating your set.
Retain it for future reference.
Record model number and serial
number of the set.
See the label attached on the set
and quote this information to your
dealer when you require service.
Owner’s Manual
For The Warranty Terms & Conditions, Please Refer To Warranty Certificate.

2
IMPORTANT SAFEGUARDS
REMOVE ALL PACKING MATERIALS FROM THIS PRODUCT BEFORE USING IT.
THIS APPLIANCE MUST BE INSTALLED ON A FLAT SURFACE. PLEASE
ENSURE THE ELECTRICITY SUPPLY TO THE APPLIANCE IS DISCONNECTED
BEFORE INSTALLING.
Please read this instruction carefully. It is advisable to keep this instruction manual in
a safe place for future reference.
1. Keep this appliance out of reach of children. Close supervision is necessary when the
appliance is operating near children or infirm persons.
2. This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning the usage of this
appliance by a person responsible for their safety.
3. Do not operate the appliance with damaged power cord or plug, after the appliance
malfunctions, or if it was dropped or damaged in any manner. Kindly return the
appliance to the nearest authorized dealer or after-sales service center for
examinations, repairs, electrical or mechanical adjustments.
WARNING –to reduce the risk of fire, electrical shock or injury to persons or
property, please read and follow below instructions carefully.
Always operate the product from a power source of the same voltage, frequency and
rating as indicated on the product identification marking.
Always switch off and unplug the plug from outlet when not in use, before assembling
or disassembling parts and before cleaning. Assemble the product completely before
operating.
To protect against the risk of electrical shock, do not immerse the product, cord or plug
into water or any other liquid.
This product should not be used in the immediate vicinity of water, such as bathtub,
washbowls, swimming pool etc, where the likelihood of immersion or splashing could
occur.
This product should not be used in the immediate vicinity of open flame or other
heating appliances where the likelihood of burning or high heat could occur.
Avoid contact with moving parts. Do not insert any object through the guard when the
product is operating.
Do not cover the guard or operate in close proximity to curtains.
Do not operate it for purposes other than its intended use.
Always disconnect the product when relocating it.

3
PRODUCT DESCRIPTION
1. Front Fan Grill
6. Adjustable Screw
2. Fan Blade
7. Decoration Cover
3. Rear Fan Grill
8. Base
4. Fan Motor
9. Base Screw and Ring
5. Stand Pole
9

4
INSTALLATION GUIDE
1. Open the packaging and remove the packaging material.
2. Unscrew the base locking screw and ring from the stand pole and insert the stand pole
through the hole in the centre of the base.
3. Tighten the base and stand pole by screwing back the ring and base locking screw.
4. Insert the round decoration cover from the top of the stand pole.
5. Loosen the screws on the extension pole and connect the extension pole with the
stand pole. Tighten the screws firmly and the height of the pole can be adjusted using
the adjustable screw knob.
6. The motor and connector have already been assembled, place the connector onto the
column holder of the stand pole, then tighten the bolts and nut with a wrench.
7. Ensure that the ground is level and firm before operating the appliance.
FAN BLADE AND GUARDS ASSEMBLY
1. Loosen the 4 screws on the face of the motor. Place the rear fan grill on to the motor
and fasten the screws with a cross screw driver.
2. Loosen the bolt on the fan blade and slide the fan blade on the motor shaft until firm.
3. Tighten the bolt and ensure the bolt sits onto the flat side of the motor shaft directly
when tightened.
4. Snap the front fan grill with the rear guard by connecting the guard clips firmly.

5
OPERATING INSTRUCTIONS
To Adjust Speed
Turn the speed knob for speed control:
“0” for OFF; “1” for Low Speed; “2” for Medium Speed; “3” for High Speed.
To Adjust Tilting Angle
Tilt can be adjusted by loosening the screw on the column holder and tilt to desired angle.
Once completed, re-fasten the screw firmly.
To Adjust Oscillation
Beneath the motor are two screw holes for the nut on the rod bar to go into. Set the
nut and rod bar to the outer screw hole to allow for oscillation.
To stop the oscillation, set the rod bar and nut to the inner screw hole.
Note: Always ensure the unit is turned off entirely before changing the oscillation
function.

6
CLEANING AND MAINTENANCE
1. Ensure the fan is turned off completely and unplugged from outlet before cleaning.
2. Use only a soft and damp cloth to clean the fan.
3. To clean the fan blades, unclamp the guard clips and remove the front fan grill.
4. Wipe the fan blades and grills carefully.
5. Reassemble the fan by snapping the front grill back into place.
WARNING:
Do not immerse the appliance into water and never let the motor housing be in
contact with water
Do not use any cleaning chemicals such as detergents and abrasives.

7
MAIN SPECIFICATION
Voltage : 220-240V, 50/60Hz
Rated Power : 180W
Fan Size : 26-Inch
Motor : 3-Speed
NOTICE
This product must not be disposed together with domestic waste. It has to be disposed at an
authorized place for recycling of electrical and electronic appliances. By collecting and recycling
waste, you help to save natural resources and make sure the product is disposed in an
environmentally friendly and healthy way.

8