Elba ESF-A1633GR User manual

For The Warranty Terms & Conditions, Please Refer To Warranty Certificate
Owner’s Manual
Please read this manual carefully before
operating your set.
Retain it for future reference.
Record model number and serial number
of the set.
See the label attached on the set and
quote this information to your dealer
when you require service.
STAND FAN
MODEL: ESF-A1633GR(WH)

REMOVE ALL PACKING MATERIALS FROM THIS PRODUCT BEFORE
USING IT. THIS APPLIANCE MUST BE INSTALLED ON A FLAT SURFACE.
PLEASE ENSURE THE ELECTRIC SUPPLY TO THIS APPLIANCE IS
DISCONNECTED BEFORE INSTALLING.
Please read this instruction carefully. It is advisable to keep this instruction
manual in a safe place for future reference.
SAFETY PRECAUTIONS
1. Keep this appliance out of reach from children. Do not let them to operate
the appliances without supervision.
2. To protect against the risk of electrical shock, do not immerse the product,
cord or plug into water or any other liquid.
3. This product is for household and indoor use only.
4. This product is not intended for use by person (including children) with
reduced physical, sensory or mental capabilities unless they have been
given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
5. If the power cord or plug in damaged, it must be replaced by the service
centre or a qualified service technician to avoid hazard.
WARNING - to reduce the risk of fire, electrical shock or injury to persons or
property, please read and follow below instructions carefully:
Always operate the product from a power source of the same voltage,
frequency and rating as indicated on the product identification marking.
Do not operate this product if it has malfunctioned, damaged cord or plug or
appears damaged in any way. Return the complete product to the place of
purchase for inspection, repair or replacement.
This product should not be used in the immediate vicinity of water, such as
bathtub, washbowls, swimming pool etc. where the likelihood of immersion or
splashing could occur.
Always switch off and unplug the plug from outlet when not in use, before
assembling or disassembling parts and before cleaning. Fully assemble the
fan before operating.
Avoid contacting with moving parts. Do not insert any object through the
guard when the appliance is operating.
Do not cover the guard or operate in close proximity to curtains, etc.
Always disconnect the appliance before moving it from one location to
another.
Make sure this appliance is installed on a flat surface to avoid overturning.
ASSEMBLY INSTRUCTIONS

1. Place the fan base on a solid and flat surface.
2. Using the screw provided, tighten the column of the stand fan to the fan base.
3. Withdraw the steel pipe from the column and fasten with the fastener at
suitable height.
4. Mount the fan body onto the steel pipe and tighten with the screw provided.
Make sure all screws have been fixed and fasten tightly.
5. Unscrew and remove the spinner clockwise and the PVC sleeve from the
motor shaft.
6. Unscrew and remove the plastic nut counter-clockwise from the motor shaft.
7. Fix the rear guard in matching the position and make sure the handle is
position on top.
8. Screw the plastic nut tightly to the rear guard.
9. Fix the fan blade onto the motor shaft until it reaches the retaining pin.
10.Screw the spinner tightly to hold the fan blade. Make sure the fan blade does
not loose.
11.Place the front guard in position and tighten with the ring attached to the rear
guard.
OPERATING INSTRUCTIONS
1. Connect the plug to the electrical mains and switch on the power. The display will
turn on followed by a beep sound.
2. The room temperature is shown on the display.
3. Press the “ON” button from the fan and the fan will start operating in Low speed.
Press the button again to switch from Normal Speed and High Speed.
4. The corresponding speed will be shown on the display indicated as 1, 2 and 3.
5. Press the “Swing” button to oscillate the fan left and right. To stop the oscillation,
press the button again.
Note: Do not attempt to adjust the oscillation manually. It will damage the
synchronous motor.
6. Press the “Mode” button to select Natural and Sleep mode. The corresponding
wind mode is shown on the display.
7. To preset the timer to turn off the fan, press the TIMER button to set the required
timer. Each interval has half an hour from 0.5 hours to maximum of 9 hours.
Note: To cancel the timer function, press the “TIMER” button until the
timer runs out and not displayed.
8. Press the “Off” button to turn off the fan.
9. To adjust the vertical angle, turn off the fan. Hold the top of the guard with your
hand. Press or lift the bottom of the guard to your desired angle.

PRODUCT DESCRIPTION
REMOTE CONTROL
1. The remote control requires 2 x AAA size batteries.
2. Open the battery compartment by sliding the cover down.
3. Insert the batteries noting the polarity indicated in the battery compartment.
4. Remote control operations are identical to the functions on the fan control panel.

CLEANING AND MAINTENANCE
Clean the appliance with a damp cloth with mild cleaner. Do not use chemical,
steel, wooden or abrasive cleaners to clean the appliance.
WARNING: DO NOT IMMERSE THE APPLIANCE INTO WATER. ENSURE
THAT THE FAN IS UNPLUGGED FROM THE POWER SUPPLY BEFORE
REMOVING THE GUARD.
MAIN SPECIFICATION
Voltage : 220-240V/50Hz
Rated Power: 60W
Fan Size : 16-inch
Motor : 3-Speed
NOTICE
This product must not be disposed together with domestic waste. It has to be
disposed at an authorized place for recycling of electrical and electronic
appliances. By collecting and recycling waste, you help to save natural
resources and make sure the product is disposed in an environmental friendly
and healthy way.