Elba EWMF-B1641(GR) User manual

For The Warranty Terms & Conditions, Please Refer To Warranty Certificate
Owner’s Manual
Please read this manual carefully before
operating your set.
Retain it for future reference.
Record model number and serial number
of the set.
See the label attached on the set and
quote this information to your dealer
when you require service.
WALL FAN
MODEL: EWMF-B1641(GR)

2
REMOVE ALL PACKING MATERIALS FROM THIS PRODUCT BEFORE USING IT.
THIS APPLIANCE MUST BE INSTALLED ON A FLAT SURFACE. PLEASE ENSURE
THE ELECTRIC SUPPLY TO THIS APPLIANCE IS DISCONNECTED BEFORE
INSTALLING.
Please read this instruction carefully. It is advisable to keep this instruction manual in a
safe place for future reference.
SAFETY PRECAUTIONS
1. Keep electrical appliances out of reach from children. Do not let them to operate the
appliances without supervision.
2. To protect against the risk of electrical shock, do not immerse the product, cord or
plug into water or any other liquid.
3. This product is for household and indoor use only.
4. This product is not intended for use by person (including children) with reduced
physical, sensory or mental capabilities unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
5. If the power cord or plug in damaged, it must be replaced by the service centre or a
qualified service technician to avoid hazard.
WARNING - to reduce the risk of fire, electrical shock or injury to persons or property,
please read and follow below instructions carefully:
Always operate the product from a power source of the same voltage, frequency and
rating as indicated on the product identification marking.
Do not operate this product if it has malfunctioned, damaged cord or plug or appears
damaged in any way. Return the complete product to the place of purchase for
inspection, repair or replacement.
This product should not be used in the immediate vicinity of water, such as bathtub,
washbowls, swimming pool etc. where the likelihood of immersion or splashing could
occur.
Always switch off and unplug the plug from outlet when not in use, before assembling
or disassembling parts and before cleaning. Fully assemble the fan before operating.
Avoid contacting with moving parts. Do not insert any object through the guard when
the fan is operating.
Do not cover the guard or operate in close proximity to curtains, etc.
Always disconnect the fan when moving it from one location to another.

3
PRODUCT DESCRIPTIONS
3-Speed Pull Switch
Blade Assembly
Front Grille Guard
Guard Ring Clip
Oscillating Control Switch
Wall Mounting Bracket (Rear)

4
ASSEMBLY INSTRUCTIONS
1. Remove all packaging material and wire fastener from the product.
2. Drill 3 holes on the wall with a distance complied with the hole on the wall bracket (2).
3. Press the screw anchors provided into holes.
4. Mount the hanging bracket (2) on the wall with three screws (1) provided (Fig 1).
(Fig 1) (Fig 2)
5. Hang the rear motor (3) with the holes (11) fixed onto the hanging bracket (2) (Fig 2).
6. Remove the protecting tube (12) from the motor shaft.
7. Loosen the rear guard locking nut (5) from the motor & housing assembly (A).
8. Position the rear guard (4) firmly to the motor & housing assembly (A) and fasten by turning
the rear guard locking nut (5) clockwise tightly.
9. Push the fan blade (6) along the motor shaft. Fasten securely using the fan blade locking nut
(7) by turning anticlockwise.
10.Press the front guard (8) to attach with rear guard (4) until both guards are properly fitted (Fig
5). Secure both guards firmly by tightening the guard ring clip (9) (Fig 6).
(Fig 3) (Fig 4)
(Fig 5) (Fig 6)

5
OPERATING INSTRUCTIONS
1. Operate the relevant speed by pulling the switch for the required fan speed. ‘0’ to
turn OFF, ‘1’ for Low Speed, ‘2’ for Medium Speed and ‘3’ for High Speed.
2. To make the fan head oscillate, pull the oscillating control switch. To stop the
oscillation, pull the oscillating control switch again.
WARNING: Do not adjust the oscillating angle by hand. It will damage the
synchronous motor.
3. To adjust the tilt of the fan head, firstly fix the body with one hand and then push
the motor part up or down to adjust it to the appropriate position.
WARNING: The fan should be switched off when making this adjustment.
NOTE: The fan head will not latch into the low or mid position until the guard and
blade are fitted to the motor.
CLEANING AND MAINTENANCE
Clean the appliance with a damp cloth with mild cleaner. Do not use chemical, steel,
wooden or abrasive cleaners to clean the appliance.
WARNING: DO NOT IMMERSE THE APPLIANCE INTO WATER. ENSURE THAT THE
FAN IS UNPLUGGED FROM THE POWER SUPPLY BEFORE REMOVING THE
GUARD.
MAIN SPECIFICATION
Voltage : 220-240V/50Hz
Rated Power: 60W
Fan Size : 16-inch
Motor : 3-Speed
NOTICE
This product must not be disposed together with domestic waste. It has to be disposed at an authorized
place for recycling of electrical and electronic appliances. By collecting and recycling waste, you help to
save natural resources and make sure the product is disposed in an environmental friendly and healthy
way.

6