Elba ESF-A1632D(BL) User manual

For The Warranty Terms & Conditions, Please Refer To Warranty Certificate
Owner’s Manual
Please read this manual carefully before
operating your set.
Retain it for future reference.
Record model number and serial number
of the set.
See the label attached on the set and
quote this information to your dealer
when you require service.
STAND FAN
MODEL: ESF-A1632D(BL)
ESF-A1632D(PK)

REMOVE ALL PACKING MATERIALS FROM THIS PRODUCT BEFORE USING IT. THIS
APPLIANCE MUST BE INSTALLED ON A FLAT SURFACE. PLEASE ENSURE THE
ELECTRIC SUPPLY TO THIS APPLIANCE IS DISCONNECTED BEFORE INSTALLING.
Please read this instruction carefully. It is advisable to keep this instruction manual in a
safe place for future reference.
SAFETY PRECAUTIONS
1. Keep electrical appliances out of reach from children. Do not let them to operate the
appliances without supervision.
2. To protect against the risk of electrical shock, do not immerse the product, cord or
plug into water or any other liquid.
3. This product is for household and indoor use only.
4. This product is not intended for use by person (including children) with reduced
physical, sensory or mental capabilities unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
5. If the power cord or plug in damaged, it must be replaced by the service centre or a
qualified service technician to avoid hazard.
WARNING - to reduce the risk of fire, electrical shock or injury to persons or property,
please read and follow below instructions carefully:
Always operate the product from a power source of the same voltage, frequency and
rating as indicated on the product identification marking.
Do not operate this product if it has malfunctioned, damaged cord or plug or appears
damaged in any way. Return the complete product to the place of purchase for
inspection, repair or replacement.
This product should not be used in the immediate vicinity of water, such as bathtub,
washbowls, swimming pool etc. where the likelihood of immersion or splashing could
occur.
Always switch off and unplug the plug from outlet when not in use, before assembling
or disassembling parts and before cleaning. Fully assemble the fan before operating.
Avoid contacting with moving parts. Do not insert any object through the guard when
the fan is operating.
Do not cover the guard or operate in close proximity to curtains, etc.
Always disconnect the fan when moving it from one location to another.

ASSEMBLY INSTRUCTIONS
1. Attach the column to the stand with the 4 screws as
shown.
2. Loosen and take off the height adjustment nut.
3. Slide the stand cover down the column to rest on the
stand.
4. Pull out the extension tube to a required height and
tighten the height adjustment nut.
Caution: The height adjustment nut must be fully
tightened before assembling the motor section to the
pedestal stand.
5. Fit the motor section to the pedestal stand and tighten
the thumbscrew.
Caution: The thumbscrew must be fully tightened
before the fan is operated.
6. Set the rear guard in the proper position (handle
uppermost) and screw on the guard retaining nut until
it is tight.
7. Mount the blade onto the shaft and tighten with the
blade retaining nut (counter-clockwise) firmly.
8. Open clips on the front guard and attach front guard
with rear guard (align locking screw holes).
9. Secure both guards firmly by fitting and tightening the
screw and nut.
OPERATING INSTRUCTIONS
1. Operate the control panel button for the required fan speed. ‘0’ for ‘OFF’, ‘1’ for Low
Speed, ‘2’ for Medium Speed and ‘3’ for High Speed.
2. To make the fan head oscillate, push the oscillating knob DOWN. To stop the
oscillation, pull the oscillating knob UP.
WARNING: Do not adjust the oscillating angle by hand. It will damage the
synchronous motor.
3. To adjust the tilt of the fan head, loosen the tilt adjusting screw and move to the
desired angle, then firmly tighten the tilt adjusting screw.
CAUTION: The fan should be switched off when making this adjustment.
Please note that the head will not latch into the low or mid position until the guard
and blade are fitted to the motor.
4. To adjust the height of the pedestal fan. Loosen the height adjustment nut carefully
raising or lowering the fan and firmly re-tighten the height adjustment nut.
CAUTION: The fan should be switched off when making this adjustment.

PRODUCT DESCRIPTIONS
1. Front guard
2. Guard locking screw/nut
3. Guard loop
4. Blade retaining nut
5. Blade
6. Guard retaining nut
7. Rear guard
8. Motor housing
9. Oscillating knob
10. Control panel
11. Handle
12. Height adjustment nut
13. Cross base cover
14. Cross base
15. Remote control
REMOTE CONTROL
1. The remote control requires 2 x AAA size batteries.
2. Open the battery compartment by sliding the cover down.
3. Insert the batteries noting the polarity indicated in the battery compartment.
4. Remote control operations are identical to the functions on the fan control panel.
PLACE REMOTE
CONTROL
PICTURE HERE

CLEANING AND MAINTENANCE
Clean the appliance with a damp cloth with mild cleaner. Do not use chemical, steel,
wooden or abrasive cleaners to clean the appliance.
WARNING: DO NOT IMMERSE THE APPLIANCE INTO WATER. ENSURE THAT THE
FAN IS UNPLUGGED FROM THE POWER SUPPLY BEFORE REMOVING THE GUARD.
MAIN SPECIFICATION:
Voltage : 220-240V/50Hz
Rated Power: 60W
Fan Size : 16-inch
Motor : 3-Speed
NOTICE
This product must not be disposed together with domestic waste. It has to
be disposed at an authorized place for recycling of electrical and
electronic appliances. By collecting and recycling waste, you help to save
natural resources and make sure the product is disposed in an
environmental friendly and healthy way.