Elecrow SF101 User manual

ELECROW 10.1” 1920*1080
IPS Portable Monitor
Model: SF101
USER MANUAL
Customer Support:
Should there be any questions, please feel free to let us know and contact us with
your purchase order number at [e-mail].

Table of Contents
2019 ELECROW All Rights Reserved.
C1
Chapter 01: Before Using the Product
1-1. Safety Precautions
1-1-1. Electricity and Safety
1-1-2. Installation
1-1-3. Cleaning
1-2. Package Contents
1-3. Product Description
1-3-1. Port Description
1-3-2. Button Indications
Chapter 02: Connecting and Using a Source Device
2-1. Connected to Laptop (with HDMI Port)
2-2. Connected to PC (with VGA Port)
2-3. How to Set Your PC/Laptop Monitor to Duplicate or Extend Mode & How to
Rotate the Screen
Chapter 03: Screen Setup
3-1. How to Reconfigure OSD (On-Screen Display) Menu
3-2. OSD Function Introduction
Chapter 04: Specifications
Chapter 05: Troubleshooting Guide and Warranty
5-1. Troubleshooting Guide
5-2. Warranty
5-3. Custormer Support
2
2
2
2
2
3
3
4
4
5
5
5
5-6
6
6
7-9
9
10
10
11
11

Chapter 01 Before Using the Product
1-1. Safety Precautions
2019 ELECROW All Rights Reserved.
C2
―Take the following steps when cleaning.
• 1. Power off the product and computer.
• 2. Disconnect the power cord from the product.
— Hold the power cable by the plug and do not touch the cable with wet hands. Otherwise, an electric shock
may result.
• 3. Wipe the monitor with a clean, soft and dry cloth.
• Do not apply a cleaning agent that contains alcohol, solvent, or surfactant to the monitor
• Do not spray water or detergent directly on the product.
1-1-1. Electricity and Safety.
1-1-2. Installation
1-1-3. Cleaning
• Do not use a damaged power cord or plug, or a loose power socket.
• An electric shock or fire may result.
• Do not touch the power plug with wet hands.
• An electric shock may result.
• Insert the power plug all the way in so it is not loose.
• An unsecure connection may cause a fire.
Warning
!
Warning
!
• Do not install the product near heat sources.
• A fire may result.
• Do not set down the product on its front.
• The screen may become damaged.
• Do not install the product on an unstable or vibrating surface (insecure shelf, sloped surface, etc.)
• The product may fall and become damaged and/or cause an injury.
• Using the product in an area with excess vibration may damage the product or cause a fire.

1-2. Package Contents
1-3. Product Description
2019 ELECROW All Rights Reserved.
C3
• 4. Wet a soft and dry cloth in water and wring thoroughly to clean the exterior of the product.
• 5. Connect the power cord to the product when cleaning is finished.
• 6. Power on the product and computer.
265.0mm
167.0mm
30.0mm
• 1 x Monitor
• 1 x HDMI to HDMI Cable
• 1 x Power Supply
• 1 x Metal Stand
• 1 x User Manual

1-3-1. Port Description
1-3-2 . Button Indications
2019 ELECROW All Rights Reserved.
C4
2
1
3
4
5
1
2
3
4
5
6
Speaker
HDMI: Video signal and audio input.
EAR: 3.5mm headphones audio output.
VGA: Video signal input.
LINE IN: Audio signal input when connected VGA.
DC 12V: DC 12V power port.
1
2
3
4
5
HDMI EAR VGA LINE IN DC 12V
+ - MENU AUTO
Red/Blue light, indicated the working status.
Turn on/off the monitor when it powered.
By default, the key is the hot key for volume.
When in the OSD menu, press for up/increase adjustment .
By default, the key is the hot key for volume.
When in the OSD menu, press for down/decrease adjustment.
Press to display the setting OSD menu.
When in the OSD menu, press to confirm the selection.
When in the OSD menu, press to exit the OSD menu.
Light
MENU
AUTO
+
-
1 2 3 4 5 6

Chapter 02 Connecting and Using a Source Device
2-1. Connected to Laptop (with HDMI Port)
2-2. Connected to PC (with VGA Port)
2-3. How to Set your PC/Laptop Monitor to Duplicate or Extend
Mode & How to Rotate the Screen
2019 ELECROW All Rights Reserved.
C5
DISPLAY
• 1. Connect the monitor to your PC properly and power it on.
• 2. Right click the desktop and select Screen resolution (Win 7/8) or Display settings (Win 10).
• 3. Click the Multiple display drop-down list, select Extend these displays or Duplicate these
displays.
*If you can’t see the additional monitor listed, please click Detect. If it doesn’t work. Restart
your PC then try below steps again
COMPUTER
HDMI to HDMI cable
12DC 12V Power
VGA to VGA cable
12DC 12V Power
1
2
DISPLAY 1
2

Chapter 03 Screen Setup
3-1. How to Reconfigure OSD (On-Screen Display) Menu
2019 ELECROW All Rights Reserved.
C6
• 4. Click the Orientation drop-down list, select Portrait or Landscape screen.
* If you can’t see the option of Orientation on your PC/laptop, please check if your PC/laptop
has this function.
• 1. Press the MENU button to activate the OSD menu.
• 2. Press the +/ - button to toggle between options in the menu. As you move from one icon to
another, the option item is highlighted.
• 3. To select the highlighted item on the menu press the button MENU.
• 4. Press the +/- button to select the parameter.
• 5. Press the button MENU to enter the slide bar and then use the +/- button to make your changes,
according to the indicators on the menu.
• 6. Press the AUTO to save the setting and return to the previous menu. If you want to adjust any
other functions, repeat steps 2-5.

3-2. OSD Function Introduction
Colour
Picture
2019 ELECROW All Rights Reserved.
C7
• Contrast: Controls the contrast of picture displayed. The adjusting range is from 0 to 100.
• Brightness: Controls the brightness of picture displayed. The adjusting range is from 0 to 100.
• Colour Temp: Controls the screen colour temperature of 6500K/9300K/User*.
• Colour Adjust: Use +/- to adjust the R/G/B value.
• Sharpness: Controls the details of picture displayed. The adjusting range is from 1 to 5.
*Note:Only under the User Mode, you could enter Colour Adjust.
!
Colour
Picture
Function
OSD Menu
Misc
Exit
OSD
ther
1920x1080 59.9Hz
Contrast 50- +
Brightness 50- +
Colour Temp 9300K 6500K User
Colour Adjust
Exit
Colour
Picture
Function
OSD Menu
Misc
Exit
OSD
ther
1920x1080 59.9Hz
Red 70- +
Green 70- +
Blue 70- +
Exit
Colour
Picture
Function
OSD Menu
Misc
Exit
OSD
ther
1920x1080 59.9Hz
H.Position 101- +
V.Position 0- +
Phase 0- +
Clock 255- +
Sharpness 1 2 3 4 5
Exit

Function
OSD Setting
2019 ELECROW All Rights Reserved.
C8
• Auto Adjust:Adjust all position asthmatically with best pictures displayed.
• Auto Color:Adjust the color asthmatically with best pictures displayed.
Note:Only connected to VGA port, you could adjust the parameter of Function by yourself.
!
Colour
Picture
Function
OSD Menu
Misc
Exit
OSD
ther
1920x1080 59.9Hz
Auto Adjust YES NO
Auto Color YES NO
Exit
Colour
Picture
Function
OSD Menu
Misc
Exit
OSD
ther
1920x1080 59.9Hz
Language
OSD H.Pos 50- +
OSD V.Pos 50- +
OSD Timer ON OFF
Exit
• Language: Select the OSD language.
The selections are: English/German/Korean/Chinese Traditional /Japanese/French/Spanish/Italian
/Chinese Simplified/Portuguese.
• OSD H. POS.: Adjust the horizontal position of OSD menu.
The adjusting range is from 0 to 100.
• OSD V. POS.: Adjust the vertical position of OSD menu.
The adjusting range is from 0 to 100.
• OSD Timer: Adjust the display time of the OSD menu.
The adjusting range is from 5s to 60s.

Chapter 04 Specifications
Misc
Exit
2019 ELECROW All Rights Reserved.
C9
• Exit the OSD menu.
• Input:Adjust the signal source to“VGA”or “HDMI”.
• Reset:Selects “Yes” to revert all settings to the factory default mode.
• Aspect:Adjusts the aspect ratio to“16:9” or“4:3”.
Model Name
Panel Size
Aspect Ratio
Brightness
Contrast
Resolution
Viewing angle
Display Color
Vertical Frequency
Display Mode
Response Time
Power Source
Power Consumption
Net Weight (Esti.)
SF101
10.1 inch
16:9 (W:H)
350 cd/m²
800:1(Min.)(TM)
1920*1080
80/80/80/80 (Min.)(CR≥10)
262K/16.7M (6-bit/6-bit+Hi-FRC)
60Hz
ADS, Normally Black Transmissive
13/12 (TYP)(Tr/Td)(ms)
DC 12 V (+/-0.6V)
Standby <1W, Power on <8W
489.3g
Colour
Picture
Function
OSD Menu
Misc
Exit
OSD
ther
1920x1080 59.9Hz
Input VGA HDMI
Reset YES NO
DIM Level LOW MID HIGH
Aspect 16:9
Exit

Chapter 05 Troubleshooting Guide and Warranty
2019 ELECROW All Rights Reserved.
C10
5-1. Troubleshooting Guide
• This page deals with problems that can be corrected by a user. If the problem still persists after
you have tried these solutions, please contact customer support.
5-2. Warranty
• ELECROW Monitors carry a one (1) year limited warranty from the purchase date. In order to
receive warranty service, proof of purchase of the ELECROW product is required. To obtain
warranty service, please contact Customer Support.
Problem
No Power
No Picture/No Signal
No Sound
Dark/Light Picture
Image is Blurred
Possible Solutions
1. Make sure the power cord is plugged properly.
2. Press the power button to check if the monitor is ON.
1. Check whether the monitor and the signal output device are in
the ON mode.
2. Reconnect the signal cable.
3. Check if the signal is matched with the input function.
4. Connect another available output device/signal cable/monitor
to check whether the issue is caused by the output device
hardware, the video signal to the monitor or the monitor itself.
1. Adjust the volume settings via the button.
2. Check whether the headphone is inserted.
3. The silencer is working.
Adjust the Brightness settings via the button.
Select the correct resolution.

2019 ELECROW All Rights Reserved.
C11
5-3. Customer Support
• If you have any questions, customer support is always stand by.
@[e-mail] @elecrow
• This limited warranty does not cover for:
Improper installation or maintenance; Misuse or Neglect; Repair, modification, or installation of
options or parts by you or any third party; Improper environment- Excessive or inadequate
heating or air conditioning or electrical powers failures, surges or other irregularities; Fire, flood,
earthquake or other accidents.