ElectrIQ SILENT10 User manual

SILENT10
PORTABLE AIR CONDITIONER
USER MANUAL
Thank you for choosing ElectriQ
Please read this user manual before using this innovative Air Conditioner and keep it
safe for future reference.
Visit our page www.electriQ.co.uk for our entire range of Intelligent Electricals

Page 2of 13
CONTENTS
1．
．．
．SAFETY INSTRUCTIONS ………………………………….. 3
2．
．．
．FEATURES AND PARTS LIST ………………………….... 4
3．
．．
．INSTALLATION …………………………………. …………. 5
4．
．．
．OPERATION AND SETTINGS …………………………….. 7
5．
．．
．WATER-DRAINAGE …………………………………………. 9
6．
．．
．MAINTENANCE ……………………………………………… 10
7．
．．
．TROUBLE SHOOTING …………………………………. …. 11
8．
．．
．APPENDIX ……………………………………………………. 12

Page 3of 13
SAFETY INSTRUCTIONS
Important!
•Carefully read the instructions before operating the unit
•This appliance is for indoor use only.
•Rating: This unit must be only connected to a 220-240 V / 50 Hz earthed outlet.
•Installation must be in accordance with regulations of the country where the unit is used.
•If you are in any doubt about the suitability of your electrical supply have it checked and, if
necessary, modified by a qualified electrician.
•This air conditioner has been tested and is safe to use. However, as with any electrical
appliances - use it with care.
•Disconnect the power plug from socket before dismantling, assembling or cleaning.
•Avoid touching any moving parts of the appliance.
•Never insert fingers, pencils or any other objects though the guard
•This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities. It is also not intended for use by those with a lack of
experience and knowledge, unless they have been given supervision or instruction
concerning the use of the appliance by a person responsible for their safety.
Do not leave children unsupervised with this appliance.
•Do not clean the unit by spraying it or immersing it in water.
•Never connect the unit to an electrical outlet using an extension cord. If an outlet is not
available, one should be installed by a qualified electrician.
•Never operate this appliance if the cord or plug is damaged. Ensure the power cord is not
stretched or exposed to sharp object/edges.
•A damaged supply cord should be replaced by the manufacturer or a qualified electrician in
order to avoid a hazard.
•Any service other than regular cleaning or filter replacement should be performed by an
authorized service representative. Failure to comply could result in a voided warranty.
•Do not use the appliance for any other purposes than its intended use.
•The air conditioner unit must always be stored and transported upright, otherwise
irreparable damage may be caused to the compressor; if in doubt we suggest waiting
at least 24 hours before starting the unit.
•Avoid restarting the air conditioning unit unless 3 minutes have passed since being turned off.
This prevents damage to the compressor.
•Never use the mains plug as a switch to start and turn off the air conditioning unit. Use the
provided ON/OFF switch located on the control panel.
•Always place the unit on a dry and stable surface.
•The appliance should not be installed in laundry or wet rooms
Energy Saving and Unit Safety Protection Tips
•Do not cover or restrict the airflow from the outlet or inlet grills.
•For maximum performance the minimum distance from a wall or objects should be 50cm.
•Keep the filters clean. Under normal conditions, filters should only need cleaning once every
three weeks (approximately). Since the filters remove airborne particles, more frequent
cleaning maybe necessary, depending on the air quality.
•For the initial startup set the fan speed to maximum and the thermostat to 4-5 degrees lower
than the current temperature. After, set the fan switch to low and set the thermostat to your
desired setting.
•To protect the unit we recommend not using the cooling function when the ambient temperature
is higher than 35⁰C.

Page 4of 13
FEATURES AND PARTS LIST
1. Features
Self-evaporative system - no external water tank needed
Designer inspired luxury model
Bright LED screen, indicates temperature and operation mode
On/Off timer function – allows you to choose when the unit operates
Compressor protection technology
2. Parts list:
1. Control Panel 6. Exhaust Connector
2. Air Outlet 7. Lower Filter Frame
3. Fan Blade 8. Rubber Stopper
4. Castors 9. Drain Plug Cap
5. Upper Filter Frame 10. Power Cord
Accessories:
1. Extendable Window Kit 4. Hose Connector
2. Screw, Washer, Nut (for window kit) 5. Remote control
3. Extendable Exhaust Hose (~1.5m)

Page 5of 13
INSTALLATION
Installation
Warning：
：：
：Before using this unit, please keep it upright for at least 3-4 hours.
This unit can easily be moved from one room to another.
While moving the unit please note that it must always be kept upright and then placed on an
even surface.
1. Assemble the fishtail connector on to the hose
2. Assemble the exhaust hose to the air conditioner body
Extend one head of the hose and screw it into the unit anti-clockwise. The hose can be
removed by screwing the hose clockwise.
Note: to screw it into place should take no less than three rotations.
3. In the same way connect the hose to the assembled adaptor (at least three rotations)
4. Installation of window kits:
Partially open the window and then fix the window kit to the window

Page 6of 13
5. Make sure the unit is upright and there are
no obstructions to the air inlets and outlet grills
6. Fix the other end of the hose to the air-outlet window kit
Note:
The window kit is only designed to be installed with sliding or sash windows or doors. The window kit
is not designed or to be used with any other style of windows. However the fish tail adaptor can be used with
most windows / doors.
When using the cooling mode ensure that the opening left is as small as possible.
The best form of installation is through a wall duct. By properly venting you expel hot air from your room while
efficiently cooling it.
Important safeguards
The length of the soft hose extends from 28 cm to
150 cm. If hose is extended above this length the unit
may malfunction and this can invalidate the warranty.
The outlet vent must be well ventilated and not
obstructed as this will cause the unit to overheat.
Avoid bending the air hose more than 30 degrees.

Page 7of 13
OPERATION AND SETTINGS
This portable air conditioner boasts 3 functions: cooling, dehumidifying and fan.
The fan has two speeds: high and low. Temperature range settings are: 16-31
⁰
C
The unit will also display operating function, temperature, fault diagnostic and protective
functions on the LCD screen.
1. Control instruction：
：：
：
Control panel：
：：
：
1.1 When plugged in the unit is automatically in standby status.
1.2 ON/OFF button: Press this button to turn the unit on and enter cooling mode.
The unit will be turn to cooling mode preset to 22⁰C target temperature. Press
again and the unit will switch off.
1.3 Mode button
Press this key to choose Cooling Fan, or Dehumidifying Mode.
1.4 Fan button
a) In Fan and Cooling mode:
HIGH（ ）→LOW（ ）
b) In Dehumidifying mode, the fan is auto set to low speed and cannot be changed
1.5 Timer
Press the icon to select your desired operating times.
Use the and buttons to adjust hours from 1-24.
You can only set the auto-shut off timer while the unit is operating (on)
You can only set the auto-start timer while the unit is switched off (standby)
After you have set the timer the timer will initiate and the units will start/ stop
after the selected time. If you adjust the timer or press the power key previous
settings will be cleared. Timer functions cannot be combined or repeated.
1.6 Up and Down button: set temperature and timer .
In cooling mode, the temperature can range from 16 - 31⁰C. Timer is 1-24 hrs.
Pressing and buttons simultaneously, shifts between ⁰C and ℉.

Page 8of 13
1.7 Sleep mode key :
In cooling mode, press the key and the unit will go into sleeping mode.
Press again to cancel.
It increases the target temperature with 1⁰C after an hour and readjust to 2⁰C
increase after 2 hours. Sleep mode is not operational under dehumidification and
fan only mode.
1.8 Swing button : press this key to start auto swing function left to right, press
again to cancel. Stopping the swing will lock the louvres position.
2. Remote control
1.Power ：Press this key to turn the unit on/off.
2. Timer ：Press this key to set time. Once set,
selected time will flash 5 times as confirmation
3. Down ：Press this key to turn down the temperature
or adjust time.
4. Mode ：Press this key to choose cooling, heating,
dehumidifying or fan mode
5. Up ：Press this key to turn up the temperature or
adjust time.
6. Fan ：Press this key to set low/medium/high fan
speed.
7. Sleep （Only in cooling function）：Press this key to
enable sleep mode.
8. Swing ：Press this key to control swing function.
3. Multi protective function
3.1 Anti-freezing protecting control:
When the ambient temperature is low while in Cooling Mode, the compressor and water
motor will stop working if the copper coil temperature reaches <2⁰C for over 20 seconds.
When the copper coil temperature increases to >8⁰C, the protection will be stopped
automatically.
3.2、Water-full protection:
When the water level in the internal water tank is surpassing the maximum level, the
unit will alert automatically and main led light will flash. Please discharge water in the
machine according to “Water Drainage” section

Page 9of 13
3.3 Compressor delay-protection
Except for the first power-on, the compressor can start instantly.
The compressor also runs under a 3 minute delay protection function.
3.4 Compressor protection
In cooling, dehumidifying and heating mode, if the temperature difference between
the coil temperature and room temperature is less than 3⁰C, for more than 30
minutes, the machine will enter ‘no refrigerant’ compressor protection mode.
The compressor and water spring motor will stop working.
The up fan runs at low speed and the down fan stops running
WATER-DRAINAGE
1. Manual drainage:
1.1 When the internal water tank is full the unit will stop working.
1.2 Shut off the unit and unplug. Try not to move the model abruptly as this may
cause water to spill out from internal water tank.
1.3 Place a tray under the water plug.
1.4 Screw off the drain plug and unplug the water rubber
stopper - water will drain from the container.
1.5 Put the water rubber stopper back and screw the drain
plug cap back into place
2. Continuous drainage:
2.1 Screw off the drain plug cap and unplug the water rubber stopper.
2.2 Use a water pipe to connect to the water outlet.
2.3 You can plumb this pipe into your current plumbing system, lead it outside or
use a water pump.
Note: This model has a self-evaporative function, which reduces the need to empty the
water tank.
If the unit is vented correctly most of the water is reused to cool the condenser coils and
any excess is evaporated.
Please do not use continuous drainage if you intend to use the self-evaporating facility.

Page 10 of 13
Maintenance
Cleaning
Please shut off the unit and unplug from the mains before cleaning or performing any
maintenance
Clean the surface
Clean the plastic housing with a duster or a soft wet cloth.
Do not use chemical solvents (such as benzene, alcohol or gasoline) as they may cause
irreversible damage.
Air filter cleaning
a) Clean the air filters every 2 weeks. If the air filter is blocked with dust, the unit’s
performance will be significantly affected.
b) Pull out the top and bottom filters as pictured below
c) Wash the air filters by immersing them in warm (about 40⁰C) water with a neutral
detergent.
d) Rinse it and then dry it thoroughly.
e) Carefully re-install the air filters
Please note: If used, the optional active carbon filter (cloth) should be replaced every 3-6
months based on the environment.
End of Season Maintenance：
：：
：
1. Pull out the plug from the drainage hole and empty the internal tank. You can also
drain the water by leaning the unit.
2. Then switch the unit to low fan mode.
3. Keep the unit in this mode for half day - until the conduit is dried. Doing this helps to
keep the inside of the unit dry and prevents mold developing
4. Turn off the unit and pull out the plug.
5. Coil the wire and bind it together, then put it into the accessories space.
6. Separate the air-exhaust pipe and store it safely.
7. Cover the unit and keep it in a dry place.
8. Take the batteries out of remote control and store or dispose, them safely
Keep all accessories with the unit ready for next season.