Electronics Line iconnect User manual

2-Way Wireless Outdoor Siren
Strobe Installation Guide
For more detailed information please refer to the iConnect
Installer Manual provided on our website: www.electronics-line.com

2
Table of Contents
1. Introduction................................................................................................ 3
2. Location of the Siren Strobe..................................................................... 3
3. Mounting the Siren Strobe........................................................................ 3
4. Registering the Siren Strobe .................................................................... 4
5. Testing the Siren Strobe ........................................................................... 5
6. Deleting a Siren Strobe ............................................................................. 5
7. Technical Specification............................................................................. 6

3
1. Introduction
The EL-4726 is a 2-Way Wireless Outdoor Siren Strobe for use with the iConne t 2-Way
se urity system. In the event of an alarm the ontrol system a tivates the siren and
Strobe. The Wireless Siren is sounded until the end of the ontrol-system-programmed
siren utoff. After the siren utoff has expired, the Strobe ontinues to flash until the
system is disarmed.
2. Location of the Siren Strobe
Consider the following before mounting the Siren Strobe:
•Choose a suitable mounting lo ation for the Siren Strobe.
•The Siren Strobe should be mounted on a flat surfa e in a highly visible position
for maximum deterren e against potential intruders.
•Before permanently mounting the Siren Strobe, test the re eption from the exa t
mounting position.
Note:
Always wear ear protectors when installing indoor/outdoor Siren Strobes
3. Mounting the Siren Strobe
1. Remove the s rews on both sides of the Siren Strobe and open the over
upwards.
2. Pla e the ba k over in position against the wall and mark the upper and lower
mounting holes.
3. Install wall an hors in the appropriate positions.
4. Fix the Siren Strobe to the wall using the supplied s rews.
5. The Siren Srobe is ready for registration to the iConne t 2-Way re eiver (see .
6. On e the Siren Strobe is registered, lose the over while paying spe ial
attention to the over tamper swit h.
7. Se ure the over lo king s rews.

4
4. Registering the Siren Strobe
The EL-4726 must identify itself to the iConnect 2-Way receiver as follows:
. Set the system to registration mode.
•Go to the main menu and select [9]>[ ]>[5]>[ ] (Programming > Devices >
Siren>WL Siren)
•Select a siren from the list ( -4) and press '√ʹ.
2. Open the screw cover by applying thumb pressure on the screw cover lower
part.
3. Open the covers screw and lift the front cover away from the rear housing.
4. Open the battery housing cover
5. Insert the batteries while paying attention to polarity (see Figure 4- ).
Figure 4-1: Siren Strobe – PCB Diagram
6. The Siren Strobe will send a transmission. If the transmission is successfully
received by the system it will play a confirmation sound. If no confirmation
sound is heard send another transmission by pressing and releasing the tamper
switch of the Siren Strobe.
7. As soon as 'Save?' appears press '√ʹ.

5
5. Testing the Siren Strobe
Once the Siren Strobe has been registered test the unit according to the following testing
procedure:
To perform a Siren Strobe test
1. Go to the main menu and select [7 >[0 >[3 >[1 (Service> Tests> WL Siren Test).
2. Select a siren from the list (1-4) and press '√ʹ. The selected Siren is sounded
briefly.
6. Deleting a Siren Strobe
To delete a Siren Strobe from the system:
1. Set the system to Delete mode.
•Go to the main menu and select [9 >[1 >[5 >[1 (Programming > Devices >
Siren>WL Siren).
•Select a siren from the list (1-4) and press '√ʹ.
• Press >3, and press '√ʹ. Upon the ‘OK’ confirmation request, press ʹ√ʹ
2. Open the Siren Strobe and take out the batteries
(see Figure 4-1).
3. Press the tamper switch. While the tamper switch is being pressed insert the
batteries. Within five seconds open the tamper and close it again.

6
7. Technical Specification
Frequency: 868*MHz or 433MHz
Power: 4 X CR123, 3V Li hium Ba er
y
(2 batteries for the Radio
Transceiver, 2 batteries for the Speaker)
Curren Consump io
n
(Radio):
25mA ( ransmission)
40µA (s andby)
Curren Consump ion
(Speaker):
50µA (s andby)
Maximum: 1.5A
Ba ery Life: 3 years ( ypical)
Siren Ou pu : 105dB @ 1m
S robe lens Pol
y
carbona e
Flash fre
q
uenc
y
60 imes
p
er minu e (max.)
Tamper Pro ec ion: Fron cover, removal from wall
Tempera ure: -25°C o 60°C (-4°F o 140° F)
Dimensions:
Weigh :
300 x 325 x 70 mm (11.8 x 12.8 x 208 inch)
1 Kg
*Complies wi h EN-50131 4 Grade 2 Class IV

7
Electronics Line Limited Warranty
EL and its subsidiaries and affiliates ("Seller") warrants its products to be free from defects in materials and
workmanship under normal use for 24 months from the date of production. Because Seller does not install
or connect the product and because the product ma be used in conjunction with products not
manufactured b the Seller, Seller cannot guarantee the performance of the securit s stem which uses this
product. Sellers' obligation and liabilit under this warrant is expressl limited to repairing and
replacing, at Sellers option, within a reasonable time after the date of deliver , an product not meeting
the specifications. Seller makes no other warrant , expressed or implied, and makes no warrant of
merchantabilit or of fitness for an particular purpose. In no case shall seller be liable for an
consequential or incidental damages for breach of this or an other warrant , expressed or implied, or
upon an other basis of liabilit whatsoever. Sellers obligation under this warrant shall not include an
transportation charges or costs of installation or an liabilit for direct, indirect, or not be compromised or
circumvented; that the product will prevent an persona; injur or propert loss b intruder, robber , fire
or otherwise; or that the product will in all cases provide adequate warning or protection. Bu er
understands that a properl installed and maintained alarm ma onl reduce the risk of intruder, robber
or fire without warning, but is not insurance or a guarant that such will not occur or that there will be no
personal injur or propert loss as a result. Consequentl seller shall have no liabilit for an personal
injur , propert damage or loss based on a claim that the product fails to give warning. However, if seller
is held liable, whether directl or indirectl , for an loss or damage arising from under this limited
warrant or otherwise, regardless of cause or origin, sellers maximum liabilit shall not exceed the
purchase price of the product, which shall be complete and exclusive remed against seller. No emplo ee
or representative of Seller is authorized to change this warrant in an wa or grant an other warrant .
WARNING: This product should be tested at least once a week.
CAUTION: Risk of explosion if batter is replaced b an incorrect t pe. Dispose of used batteries
according to local regulations.

8
Contacting Electronics Line 3000 Ltd.
International Headquarters:
Electronics Line 3000 Ltd.
14 Hachoma St., 75655
Rishon Le Zion, Israel
Tel: [phone]
Fax: [phone]
All rights reserved.
No part of this document may be reproduced in any form without prior written permission from
the publisher
Electronics Line 3000 Ltd. 04 2012 5IN1783 B