Eleiko 3085245-060 User manual

Eleiko Powerlifting Squat
Stand/Bench Combo
Art.no. 3085245-060

CAUTION
The equipment must be installed and used in a place whose access and supervision are specifically controlled by
the owner.
Be sure to install the equipment on a stable base and properly level the equipment. ELEIKO recommends that all
equipment is secured to floor and installed by a licensed contractor or an ELEIKO-installer.
SAFETY INSTRUCTIONS
It is the responibility of the purchaser of ELEIKO products to instruct all users and supervising personnel on
proper usage of the equipment.
1. All included warnings (labels) and instructions MUST be read before the use of any ELEIKO-equipment. Use
each equipment as it is intended for.
2. A user MUST get a medical examination and proper instructions before the use of any ELEIKO-equipment.
3. DO NOT let anyone, under any cuircumstances, use equipment that appears to be damaged. Do not try to
repair any equipment before consulting an ELEIKO technician.
4. DO NOT replace the components of ELEIKO-equipment with other none ELEIKO-equipment (magnetic safety
pin, frames, bars), do not improvise. If there are any doubts consult an ELEIKO representative prior to any
intervention.
5. DO NOT overload the equipment and DO NOT try to exceed personal strength levels.
6. Children under the age of 14 must be supervised by an adult.
7. DO NOT remove any safety labels from the ELEIKO-equipment. ELEIKO is not responsible if a label is
removed. Replace damaged labels immediately.
8. Eleiko package for products can be made of wood, be aware of splinters, MUST use gloves and proper work
wear.
9. Eleiko package material could be a risk when handling, be aware of crushing, MUST use work wear including
gloves and hard shoes.
10 . Eleiko products and packing material is heavy, MUST use proper lifting technique, work wear and hard shoes.
PREVENTITIVE MAINTENANCE & INSPECTIONS
DAILY:
Cleaning of upholstery.
REGULARLY:
Clean the surfaces on frames and tubes from dust and dirt.
Check that all bolts between parts, walls, floors are properly tightened, according to recommendations. Check
euipment for sharp edges, replace parts with sharp edges.
WARRANTY
All products manufactured by ELEIKO are warranted to the original purchaser to be free from defects in
workmanship and / or materials under normal use or service as follows:
10 years on welds on structural frame (NOT on moving parts)
1 year on upholstery
Normal wear and tear does not fall under the warranty of 10 years.
ADDITIONAL INFORMATION
This equipment is for indoor use only.
READ BEFORE INSTALLATION AND USE

600
600
600
600
Eleiko Powerlifting Squat Stand/Bench Combo is used for IPF powerlifting
competitions and training. Bench press and squat are the two
exercises it is made for.
To change height of uprights and safety arms, make sure no
person is under or close to the bar, lift the upright or safety arm
up and place the pin in correct hole, make sure to insert the pin properly.
Lower the uprights or safety arms slowly until pin is in contact.
Add sufficient
clearance, not less
than 0,6 m, on all
sides. Taking in
account the
accessibility to
remove and replace
bar and weights
Product weight
115 kg
253 lbs
Max user weight
300 kg
661 lbs
Max training weight
750 kg
1650 lbs
Dimensions (L x W x H)
2010x1650x1875 mm
80" x 65" x 74"
PRODUCT SPECIFICATIONS
FOOTPRINT AREA

Left side base
3085120A55
x1
Right side base
3085120A56
x1
Barbell support
3085221
x2
Assembly section
3085120A31
x1
Safety arm
3085120A07
x2
Left side safety base
3085120A27
x1
Right side safety base
3085120A34
x1
Upholstry
2000839
x1
Base for upholstry
3085120A57
x1
Front support
3085120A58
x1
Pin
2000799
x6 x2
Aluminiu knob
3085120A20
Washer
2000719
x8
Screw M8x16
2000747-L16
x6
Screw M10x30
2000675-L30
x8
Screw M12x25
2000743-L25
x3
Sheet metal
3085120p162
x1
RXS 5,5x32
2000855-L32
x4
CONTENTS

Hex key
6 mm
Hex key
8 mm
The table below is general torque to use for different
threads. Use these torques, if nothing else is set. Below
numbers are for screw/nut of quality 8.8.
Hex key
5 mm
Screw driver
Philipps
Would not recommend electric power tools for assembly.
THREAD
TORQUE (Nm / ftlb)
Quality 8.8
M8 24 / 17,7
M10 47 / 34,7
M12 81 / 59,7
REQUIRED TOOLS
GENERAL

Right side base
3085120A56
x1
Left side base
3085120A55
x1
Assembly section
3085120A31
x1
Screw M10x30
2000675-L30
x8
Washer
2000719
x8
Sheet metal
3085120p162
x1
1.
ASSEMBLY INSTRUCTIONS

Front support
3085120A58
x1
Base for upholstry
3085120A57
x1
Upholstry
2000839
x1
Use your fingers to fit the M8
Screws and no power tool to tighten
Make sure feets are in
opposite direction!
Screw M8x16
2000747-L16
x6
Screw M12x25
2000743-L25
x3
2.

Aluminiu knob
3085120A20
Left side safety base
3085120A27
x1
Right side safety base
3085120A34
x1
3.

Barbell support
3085221
x2
Safety arm
3085120A07
x2
Pin
2000799
x6
RXS 5,5x32
2000855-L32
x4
4.

Tighten all screws properly
For safe use, be certain pin is properly inserted
before load bar on bench.
5.

Eleiko Powerlifting Squat Stand/Bench Combo is used for IPF powerlifting
competitions and training. Bench press and squat are the two
exercises it is made for.
User Manual
1. Adjust uprights and safety arms:
To change height of uprights and safety arms, make sure no
person is under or close to the bar, lift the upright or safety arm
up and place the pin in correct hole, make sure to insert the pin properly.
Lower the uprights or safety arms slowly until pin is in contact.
If needed, use the tilt mechanism to tilt the uprights, make sure no person
is under the bar.
3. Remove or replace the bench, depending of what lift. Tigthen the
aluminium knob.
2. Place the bar in j-cups, equally in distance side ways.
3. Add weight on the bar, equally.
4. Do your lift.
5. Place the bar in the j cups.
6. Remove weight from bar
7. If more lifts, repeat from 1.
6.

Eleiko Group AB | Klastorpsvägen 18 | SE-302 62 HALMSTAD | Sweden
E-mail: [email protected] | Phone: [phone]
www.eleiko.com
rev. 1908