Eleiko 3085601 User manual

ELEIKO PRESTERA
CABLE ATTACHMENT
Art.no. 3085601

Read before installation and use
Safety instructions
Warning labels
Assembly instructions - General
Tools needed
Assembly instructions - Left side
List of components
Assembly instructions - Right side
List of components
User guide
Purpose
General instructions for use
Product specifications
Care and maintenance
Preventive maintenance and inspections
Spare parts and service
Warranty
3
3
4
5
5
6
7-8
33
34-35
60
60
60
60
61
61
61
61
CONTENTS

Install and use this equipment in a place where access and supervision are specifically controlled by the owner.
Be sure to install the equipment on a stable base and level the equipment properly. Eleiko recommends that all
equipment is installed by a licensed contractor or an Eleiko installer.
This equipment is intended for indoor use only.
SAFETY INSTRUCTIONS
It is the responsibility of the purchaser of ELEIKO products to instruct all users and supervising personnel on
proper usage of the equipment.
All included warnings (labels) and instructions MUST be read before the use of any Eleiko 1.
equipment. Only use the equipment as it is intended.
A user MUST get a medical examination and proper instructions before using any Eleiko 2.
equipment.
DO NOT let anyone, under any circumstances, use equipment that appears to be damaged. Do not 3.
try to repair any equipment before consulting an Eleiko technician.
DO NOT replace components of Eleiko equipment with other, none Eleiko, equipment (magnetic 4.
safety pin, frames, bars etc.). Do not improvise! If there are any doubts, consult an Eleiko
representative prior to any intervention.
DO NOT overload the equipment and DO NOT try to exceed personal strength levels. 5.
Children under the age of 14 must be supervised by an adult. 6.
DO NOT remove any safety labels from the Eleiko equipment. Eleiko is not responsible if a label is 7.
removed. Replace damaged labels immediately.
Eleiko packaging for products an be made of wood. Be aware of splinters! You MUST use 8.
protective gloves and proper work wear.
Eleiko packaging material could be a risk when handling. Be aware of crushing! You MUST use 9.
work wear including protective gloves and hard shoes.
Eleiko products and packing material are heavy, You MUST use proper lifting techniques, work 10.
wear and hard shoes.
- 3 -
READ BEFORE
INSTALLATION AND USE

Pinch point
- 4 -
WARNING LABELS

1,5 m 1,5 m
0,6 m 0,6 m
Socket Wrench Size 24mm
Allen Key Size 6 Allen Key Size 5 Allen Key Size 4
Allen Key Size 8
- 5 -
Before assembly, make sure you have enough clearance on all
sides of the equipment, not less than 0,6 meters. Take in account
the accessibility to remove and replace bar and weights.
TOOLS NEEDED
You need the following tools to assemble the equipment.
NOTE: Do not use electric power tools for assembly.
Wrench Size 24mm Wrench Size 17mm
ASSEMBLY INSTRUCTIONS

ASSEMMBLY INSTRUCTIONS
LEFT SIDE
ASSEMBLY INSTRUCTIONS FOR THE RIGHT SIDE CAN BE FOUND ON
PAGE 33
- 6 -

2001592
1x
2x
3085601 p3
1x
3085601 a1
3085601 a3
1x
1x
3085601 a7
2x
3085601 p11
1x
3085601 p25
1x
3085601 a6
1x
3085601 a8 3085601 a9
1x
CABLE
1x
3085570 p29
2001615
3000147
3000146
1x
3085601 a2
19x
2001590
- 7 -
LIST OF COMPONENTS

3085601 p8
1x
2x
3085570 p33
2x
3085570 p34
3085601 p9
1x
2x
2001000
1x
3060377
1x
3085601 p6
M16 x 110
2001019-L110
1x
Washer M16
2001421
10x
Locking Nut M16
2001379
5x
M16 x 100
2001385-L100
5x
K6S M8 x 12
2001620-L12
14x
Washer M8
2001422
16x
K6S M8 x 30
2000747-L30
2x
4x
3061757 p30
FOR ELEIKO PRESTERA
STORAGE PINS
Nut M16
2000780
1x
2001483
1x
1x
Double Wheel Kit
3085601 p15
2001482
2001619-L45
1x
2001482
3085570 p36
2001619-L45
Single Wheel Kit
Hollow Screw
1x
2001485
2000780-M12
- 8 -
LIST OF COMPONENTS

- 9 -
BEFORE YOU START THIS ASSEMBLY,
REMOVE EVENTUAL GLIDING J-CUPS
AND/OR GLIDING SAFETY ARMS!
ALSO REMOVE THE RUBBER DAMPERS IF
YOU HAVE ELEIKO PRESTERA STORAGE
PINS, SAVE THESE FOR LATER!
IF YOU HAVE ALSO PURCHASED A SVR
INSERT PLATFORM, INSTALL THE
PLATFORM FIRST!
PREPARATION

E
REMOVE FLOOR BEAM AND SAVE ALL SCREWS!
YOU WILL NOT NEED THE FLOOR BEAM ANYMORE!
1.
- 10 -

2001592
1x
2.
- 11 -
REMOVE TOP COVER PLATE!
YOU WILL NOT NEED SCREWS AND COVER PLATE ANYMORE.
SAVE THE PARTS IN CASE YOU REMOVE THE CABLE RACK IN THE FUTURE!

AF
BIGGER HOLE TOWARDS FRONT FLOOR BEAM!
Nut M16
1x
ONLY FOR DOUBLE HALF RACK
WITH TWO CABLE ATTACHMENTS, FRONT AND BACK
1623,23
B
IF YOU HAVE A DOUBLE HALF RACK AND PLAN TO HAVE TWO CABLE
ATTACHMENTS, FRONT AND BACK, CHANGE THIS SCREW TO A M16x100.
ALSO REMOVE BOTH WASHERS AND REPLACE THE LOCKING NUT!
M16x100
M16x110
TRIANGLE MUST POINT TOWARS
THE FRONT OF THE RACK!
M16 x 100
1x
3.
- 12 -
MOUNT THE NEW FLOOR BEAM!
USE THE SCREWS FROM STEP 1!

3085601 p8
1x
K6S M8 x 12
4x
Washer M8
4x
4.
- 13 -

I
1x
3085601 a8
M16 x 100
2x
Washer M16
4x
Locking Nut M16
2x
5.
- 14 -

M16 x 100
2x
Washer M16
4x
Locking Nut M16
2x
1x
3085601 a7
6.
- 15 -

2x
3085601 p3
2x
3085570 p33
2x
3085570 p34
7.
- 16 -

M
8.
- 17 -
PLACE RODS IN TILTED POSITION IN THESE HOLES.
RUBBER DAMPERS AND DISTANCE PLATES DOWN!
WIPE OFF BOTH RODS WITH A CLEAN CLOTH!

19x
2001590
9.
- 18 -
ASSEMBLE THE WEIGHT STACK PLATE BY PLATE!
MAKE SURE THE FIRST PLATE IS PUSHED ALL THE WAY DOWN AND LOCKED IN POSITION!

1x
3085601 a1
10.
- 19 -

TOP WEIGHT AND PLASTIC TOP SUPENSION
MUST BE TURNED THIS WAY!
3085601 p9
1x
1x
3085601 a2
11.
- 20 -
MOUNT TOP WEIGHT AND PLASTIC TOP SUSPENSION!
PUSH TO VERTICAL POSITION!