Eleiko PRESTERA SMITH ATTACHMENT User manual

ELEIKO PRESTERA
SMITH ATTACHMENT
Art.no. 3085513

Read before installation and use
Safety instructions
List of components
Assembly instructions
Tools needed
User guide
Purpose
General instructions for use
Product specifications
Care and maintenance
Preventive maintenance and inspections
Spare parts and service
Warranty
3
3
4
5
5
7
7
7
7
7
7
7
7
CONTENTS

Install and use this equipment in a place where access and supervision are specifically controlled by the owner.
Be sure to install the equipment on a stable base and level the equipment properly. Eleiko recommends that all
equipment is secured to floor and installed by a licensed contractor or an Eleiko installer.
This equipment is intended for indoor use only.
SAFETY INSTRUCTIONS
It is the responsibility of the purchaser of ELEIKO products to instruct all users and supervising personnel on
proper usage of the equipment.
All included warnings (labels) and instructions MUST be read before the use of any Eleiko 1.
equipment. Only use the equipment as it is intended.
A user MUST get a medical examination and proper instructions before using any Eleiko 2.
equipment.
DO NOT let anyone, under any circumstances, use equipment that appears to be damaged. Do not 3.
try to repair any equipment before consulting an Eleiko technician.
DO NOT replace components of Eleiko equipment with other, none Eleiko, equipment (magnetic 4.
safety pin, frames, bars etc.). Do not improvise! If there are any doubts, consult an Eleiko
representative prior to any intervention.
DO NOT overload the equipment and DO NOT try to exceed personal strength levels. 5.
Children under the age of 14 must be supervised by an adult. 6.
DO NOT remove any safety labels from the Eleiko equipment. Eleiko is not responsible if a label is 7.
removed. Replace damaged labels immediately.
Eleiko packaging for products can be made of wood. Be aware of splinters! You MUST use 8.
protective gloves and proper work wear.
Eleiko packaging material could be a risk when handling. Be aware of crushing! You MUST use 9.
work wear including protective gloves and hard shoes.
Eleiko products and packing material are heavy, You MUST use proper lifting techniques, work 10.
wear and hard shoes.
- 3 -
READ BEFORE
INSTALLATION AND USE

6x
2000677-L20
3085514
1x
6x
2001356
12x
2001421
6x
2001379
6x
2001385-L120
3085513A1
1x
- 4 -
LIST OF COMPONENTS

Wrench 24 mm
1x
Locking handel 1/2
1x
Socket 1/2 24 mm
1x
Allen key 5 mm
1x
600
600
600 600
Free area
- 5 -
Before assembly, make sure you have enough clearance on all
sides of the equipment. Take in account the accessibility to
remove plates.
TOOLS NEEDED
You need the following tools to assemble the equipment.
NOTE: Do not use electric power tools for assembly.
ASSEMBLY INSTRUCTIONS

40 Nm/ 30ftlb
loose screws
C
C
C
1.
- 6 -

- 7 -
PURPOSE
This unit is intended to used for a varity of different lifts like squats, presses and lunges. The product has a fixed
barbell which follow a guided path along the chromed shafts. By lifting and rotating you can rack on and rack off.
GENERAL INSTRUCTIONS FOR USE
Adjust the safety stoppers at correct hight, if trouble with lifting, safety stoppers will stop the bar falling. 1.
Load plates on the sleeves, load same amount of plates on each side. 2.
Use collars to keep the plates on the sleeve. 3.
Release the barbell by lifting a few cm (an inch), rotate. The bar is now free to move and follow your motion 4.
up and down.
To end the exercise, rotate the barbell and lower the bar a few cm(an inch). Make sure barbell is secured 5.
before you let go of the barbell.
Unload the sleeves 6.
Na kg / Na lbs
200 kg / 440 lbs
52 kg / 114 lbs
178 x 1929 x 1968 mm
7" x 76" x 77,5"
PRODUCT SPECIFICATION
Max user weight
Max training weight
Product weight
Dimensions (L x W x H)
PREVENTIVE MAINTENANCE AND INSPECTIONS
NOTE: The safety level of the equipment can only be maintained if it is examined regularly for damage and wear.
Regularly:
· Clean surfaces on the frames and tubes from dust and dirt.
· Clean bar with nylon brush.
· Check that all bolts between parts, walls and floors are properly tightened, according to recommendations.
· Check equipment for sharp edges. Replace parts with sharp edges.
See also www.eleiko.com.
SPARE PARTS AND SERVICE
Contact Eleiko for spare parts and service:
Eleiko Group AB | Klastorpsvägen 18 | SE-302 62 HALMSTAD | Sweden
E-mail: [email protected] | Phone: [phone]
WARRANTY
All products manufactured by ELEIKO are warranted to the original purchaser to be free from defects in workmanship
and / or materials under normal use or service as follows:
· 10 years on structural frame welds (NOT on moving parts)
Normal wear and tear do not fall under the 10-year warranty.
USER GUIDE
CARE AND MAINTENANCE

Eleiko Group AB | Klastorpsvägen 18 | SE-302 62 HALMSTAD | Sweden
E-mail: [email protected] | Phone: [phone]
www.eleiko.com
rev. 2105