Eleiko ATLETICA OLYMPIC Operation instructions

ELEIKO ATLETICA
OLYMPIC BENCH PRESS
Art.nr 3061390

CAUTION
The equipment must be installed and used in a place whose access and supervision
are specifically controlled by the owner.
Be sure to install the equipment on a stable base and properly level the equipment.
ELEIKO recommends that all equipment is secured to floor and installed by a licensed
contractor or an ELEIKO-installer.
SAFETY INSTRUCTIONS
It is the responibility of the purchaser of ELEIKO products to instruct all users and
supervising personnel on proper usage of the equipment.
1. All included warnings (labels) and instructions MUST be read before the use of any
ELEIKO-equipment. Use each equipment as it is intended for.
2. A user MUST get a medical examination and proper instructions before the use of
any ELEIKO-equipment.
3. DO NOT let anyone, under any cuircumstances, use equipment that appears to be
damaged. Do not try to repair any equipment before consulting an ELEIKO technician.
4. DO NOT replace the components of ELEIKO-equipment with other none ELEIKO-
equipment (magnetic safety pin, frames, bars), do not improvise. If there are any
doubts consult an ELEIKO representative prior to any intervention.
5. DO NOT overload the equipment and DO NOT try to exceed personal strength
levels.
6. Children under the age of 14 must be supervised by an adult.
7. DO NOT remove any safety labels from the ELEIKO-equipment. ELEIKO is not
responsible if a label is removed. Replace damaged labels immediately.
PREVENTITIVE MAINTENANCE & INSPECTIONS
DAILY:
Cleaning of upholstery.
REGULARLY:
Clean the surfaces on frames and tubes from dust and dirt.
Check that all bolts between parts, floors are properly tightened, according to
recommendations.
WARRANTY
All products manufactured by ELEIKO are warranted to the original purchaser to be
free from defects in workmanship and / or materials under normal use or service as
follows:
10 years on welds on structural frame (NOT on moving parts)
1 year on upholstery
Normal wear and tear does not fall under the warranty of 10 years.
ADDITIONAL INFORMATION
This equipment is for indoor use only. This equipment is in compliance with SS-EN
ISO 20957-1 and the relevant chapter SS-EN 957-4.
READ BEFORE INSTALLATION AND USE

1719
1628
600 600
600 600
Bench for bench press training and weight storage.
Add sufficient
clearance, not less
than 0,6 m, on all
sides.
Product weight 80 kg / 176 lbs
Max user weight 150 kg / 331 lbs
Max training weight 350 kg / 772 lbs
Dimensions (L x W x H)
1719 x 1628 x 1292mm
68" x 64" x 51" in
PRODUCT SPECIFICATIONS
FOOTPRINT AREA

x1
Frame Left
x1
Frame Right
x1
Cross Section
x1
Middle Section
x4
Weight Pin
x4
Rubber Stop
2000684
x6
Screw M12x30
Art.no.2000743-L30
x6
Screw M8x20
Art.no.2000747-L20
x10
Screw M10x20
Art.no.2000675-L20
x8
Washer M10
Art.no.2000719
x2
Lock NutM10
Art.no.2000718
x2
J-CUP
3061390 p39
x2
J-Cup Bracket
3061390 p41
x8
Screw M10x30
Art.no.2000675-L30
x1
Upholstry
Art. no. 2000839
x4
screw M10x25
Art.no.2000675-L25
CONTENTS

Allen Key
Size 10mm
Allen Key
Size 8mm
Socket wrench and
socket size 16mm (M10)
The table below is general torque to use for different
threads. Use these torques, if nothing else is set. Below
numbers are for screw/nut of quality 8.8.
THREAD
TORQUE (Nm / ftlb)
Quality 8.8
M10 47 / 34,7
M12 81 / 59,7
REQUIRED TOOLS
GENERAL

x1
Frame Left
x1
Frame Right
x4
Screw M12x30
Art.no.2000743-L30
2000743-L30
x1
Cross Section
1.
ASSEMBLY INSTRUCTIONS

2000747-L20
x1
Middle Section
x1
Upholstry
Art. no. 2000839
x6
Screw M8x20
Art.no.2000747-L20
2.

x4
screw M10x25
Art.no.2000675-L25
x4
Lock NutM10
Art.no.2000718
x8
Washer M10
Art.no.2000719
2000675-L25
2000719
2000718
3.

2000684
2000675-L20
2000685
x4
Weight Pin
x4
Screw M10x25
Art.no.2000675-L25
x8
Rubber Stop
2000684
4.

2000675-L30
3061390 p41
3061390 p39
x2
J-CUP
3061390 p39
x2
J-Cup Bracket
3061390 p41
x8
screw M10x30
Art.no.2000675-L30
5.

Eleiko Group AB | Klastorpsvägen 18 | SE-302 62 HALMSTAD | Sweden
E-mail: [email protected] | Phone: [phone]
www.eleiko.com
rev. 1902