Elite Screens EDGE FREE Aeon StarBright 9 Series User manual

User manual
Aeon StarBright 9™ Series
Ceiling Ambient Light Rejecting EDGE FREE®
Fixed Frame Screen
(Splicing type)
Rev. V20211204DT
(DS0207)
Elite Screens

User manual Aeon series fixed frame –AR2-S
Rev. V05242022DT (DS0207) Elite Screens 2
Product maintenance and precautions
Dust, dirt, and scratches on the projection screen surface will affect the quality and performance of the
projection image. Follow the instructions below to properly maintain the screen.
Cleaning and maintenance:
1) The screen surface has a horizontal linear structure. DO NOT wipe the screen up and down or
in a circular motion. Wipe gently from left to right only.
2) Clean the dust on the screen surface with a soft brush or microfiber cloth. A rough/coarse towel
or cloth may damage the screen’s surface.
3) Gently wipe the screen with a lightly moistened white lint free cloth with water or with a neutral
detergent mixed with water.
Attention:
1) Don’t touch the screen material to avoid leaving fingerprints.
Use gloves when handling the material.
2) Don’t scratch the material, as it will leave permanent markings on the screen’s surface.
3) Don’t point to the screen material with a fingertip or other sharp objects to prevent damage to
the material.
4) Don’t use acetone, benzene, alcohol, and any other organic solvents to clean the screen material.
Using such chemicals will permanently damage the screen.
※ Note: this product is only suitable for standard throw projectors
Prepare tools before installation
1. Tape measure x1
2. Electric drill x1
3. Pencil x1
4.Screwdriver x1
5.Hammer x1

User manual Aeon series fixed frame –AR2-S
Rev. V05242022DT (DS0207) Elite Screens 3
Hardware and Parts List
Please check whether the following accessories exist before installation. If there are any missing
accessories, please contact us immediately.
A. Elbow joints x 8
B. Top/Bottom Horizontal frame x 4
C. Left/Right vertical frame x 2
(Part 1 x 2 + Part 2 x 2)
D. Top/Bottom Horizontal edge trim x 4
E. Sliding nut x 4
F. Wall bracket x 4
(Part 1 x 2 + Part 2 x 2)
(Installed in the frame already)
G. M3x8 screw x 20
H. M5x8 screw x 56
I. M5x50 Screw / Anchor x 4
(Including 8pcs have been
installed on the sliding nuts)
J. M4x40 screw x 26
K. M3 Hex key x 2
L. Fiberglass rod x 6
M. Center support bar x 1
N. Gloves x 2
O. Screen material x 1
P. Corner cover x 4
Q. Adjustment bar x 6
R. Protection sheet x 1
S. Left/Right vertical edge trim x 2
T. Long Center joints x 4

User manual Aeon series fixed frame –AR2-S
Rev. V05242022DT (DS0207) Elite Screens 4
Frame assembly
Remove all items from the box. Find the Protection sheet (R), unfold it, and lay it down on a clean floor.
Proceed to assemble the frame as follows:
1. Insert Elbow joints (A) and Long center joints (T) into one set of the Horizontal frames (B),
as shown in the figure below.
ATTENTION: Place the frame pieces away from each other to avoid scratching them during
assembly.
2. Insert the Left/Right vertical frames (C) into the Elbow joints (A). Then connect (Part 1 + Part
2) of the Horizontal frame (B), and assemble the frame as shown below.
Top section
Bottom section
Sectional view
Top Horizontal frame (B)
Push
Push
Left/Right vertical frame (C)
Horizontal frame (B)
(Part 1 + Part 2)
Elbow joints (A)
Elbow joints (A)
Long center joints (T)
Bottom Horizontal frame (B)
Push
Push

User manual Aeon series fixed frame –AR2-S
Rev. V05242022DT (DS0207) Elite Screens 5
3. Fasten the center joints on the Horizontal Frames (B) using the screws. Then, make sure all four
corners are properly in place to form a perfect square, then fasten the four angles with the M5x8
flat head screws (H).
Screen Material Installation
1. Put on the installation Gloves (N) to avoid touching the screen material with bare hands which
typically leave oily fingerprint marks that cannot be removed (Figure 1). Then, remove the
assembled frame from the Protection sheet (R) and place it in a safe area.
2. Take the Screen material (O) out of the packaging tube and set it gently on the Protection sheet
(R). Gently press one end of the screen material (screen edge) with a suitable weighted object or
just by using hand pressure face down (DO NOT press and crush the screen material). Two people
should hold the other end (rolled up end) slowly rotate the screen a clockwise direction (Figure 2).
Heavy weighted object or
hand pressure
Backside of the screen
(Figure2)
M5x8 flat head screws (H)
(Figure 1)
Four corners join correctly to
form a perfect rectangle.

User manual Aeon series fixed frame –AR2-S
Rev. V05242022DT (DS0207) Elite Screens 6
3. Once the material has been completely unrolled, lay the material completely flat with the front
facing down on a clean surface in a horizontal position (Figure 3)
There are thumbtacks fixed on the paper tube at the end of screen expansion. Pay attention
to the thumbtacks to avoid stabbing yourself when removing them!
4. Insert the Fiberglass rods (L) through the sleeves on the edges of the screen material. The long
rods (1, 2) are used on the vertical edges of the screen material, and the short rods (3, 4, 5, 6) are
used on the horizontal edges, as shown below.
(Figure3)
Backside of the screen
Front side of the screen
Clean, flat area that does not
harm the screen’s surface
Note: Screen back facing up
(Face down)
Backside
of screen
Protection film
The purpose of the protection film is to protect the
screen during installation. If the film is moved,
please try to move back the film into the center.
Do not remove protection film during installation,
Make sure the film is at the center of screen.
Backside
of screen
2
Fiberglass rod (L)
3
1
5
Long side of the frame
Short side of
the frame
Short side of
the frame
Long side of the frame
4
6

User manual Aeon series fixed frame –AR2-S
Rev. V05242022DT (DS0207) Elite Screens 7
5. Insert the two long Adjustment bars (Q) on the fiberglass rods (1, 2) of the short side of the
screen material and two short Adjustment bars (Q) on the fiberglass rod (3, 4, 5, 6) of the long
side of the screen.
Adjustment bars position
Adjustment bar installation
※The adjustment bar is installed into the groove along the fiberglass rod
1
2
5
3
4
6
Screen material (O)
Adjustment bar (Q)
※ All four angles should have the
adjustment bars with the beveled angle
※ The upper and lower (middle points) adjustment
bars have right-angle edges

User manual Aeon series fixed frame –AR2-S
Rev. V05242022DT (DS0207) Elite Screens 8
Center support bar installation
Push the Center support bar (M) in the middle of the frame and align each end of the support bar with
the top and bottom frames.
6. Carefully and gently place the assembled frame on top of the screen material. Make sure to not allow
the angle edge of the frame to come in direct contact with the screen material to avoid puncturing it.
7. Ensure that the sliders in the left and right short frames (two sliders on each side) are fixed 1/4 of the
frame away from both top/bottom ends.
Adjustment Bar to Frame Installation
8. Once all the four corners of the frame have been
properly aligned on the marked areas on the
material, two people should insert the M4x40
screw (J) through the frame hole and fasten it on
the adjustment bar (Q) by turning it twice.
Note: Don’t over tighten. Adjust until all
screws have been inserted.
9. Secure and tighten the M4x40 screw (J) using
the M3 Hex Key (K) symmetrically in the following sequence: 1-1 → 2-2 → 3-3 → 4-4 → 5-5 → 6-6
→ 7-7 → 8-8 → 9-9 → 10-10 → 11-11 → 12-12 → 13-13.
ATTENTION: Make sure the screen material does not shift and remains aligned on all 4 corners of the
frame before proceeding to 4-4→ 5-5 → 6-6 → 7-7. Failure to keep material aligned will cause it to get
squeezed when installing the edge trim and result in damage.
Note: The distance between the adjustment bar and the edge of the frame is
approximately 0.11-0.14” (3-4mm) after completely fastened.
Align the frame with
the marked lines
Note: The screen back facing up
Horizontal frame (B)
Center support bar (M)
push
Center support bar
（M）
0.11”- 0.14”

User manual Aeon series fixed frame –AR2-S
Rev. V05242022DT (DS0207) Elite Screens 9
Illustration of steps above
10. After installing the adjustment bar to the frame, lift the frame (two people) to check the screen surface.
If there are visible waves on the screen surface, adjust the tightness of the screws to make the screen
surface flat.
DO NOT PROCEED TO THE EDGE TRIM INSTALALATION STEP IF THERE ARE ANY WAVES OR
THE SCREEN SURFACE IS NOT FLAT.
※Insert M4x40 screw, fasten
it to the adjustment bar and
turn it twice
Screen material (O)
M3 Hex Key (K)
Adjustment bar (Q)
Fiberglass rod (L)
※Tighten the screws with the
M3 hex key
※Turn the adjustment bar
and place it on the back of
the frame
M3 Hex Key (K)
※Diagram of corner and
horizontal screw installation
Check the screen surface
to make sure it is flat.

User manual Aeon series fixed frame –AR2-S
Rev. V05242022DT (DS0207) Elite Screens 10
Edge trim Installation
1. Place the Edge trim (D) on the four sides of the frame.
(Note: The edge trim with the LOGO on the front should be on the bottom frame right of the
screen and can also be distinguished by the product label on the backside.)
2. Place all the trim pieces along the edge of screen material, adjust the trim so that the top and
bottom trim pieces are touching and show no gaps in the center. Then align the M3x8 screw (G)
with the A & B holes as shown in the illustration below.
Edge trim corner installation
Place the Edge trim (D) on the frame, overlap in the frame angle seam, and align them with the
hole on the frame leaving no gaps. Then fasten screw A then B.
* Leave approximately a 2mm gap on screw A for the next step.
A
B
Edge trim (D)
※Edge Trim Assembly Illustration
M3x8 screw (G)
Screen material (O)
Verify that product labels are on the
bottom of the edge trim frame.
A
B
Fasten all the screws on the edge trim.
4 screws are required for each corner and
2 screws for each horizontal frame.