Elite Screens VMAX2 (Plus) Series User manual

E
l
i
t
e
SCREENS
Elite
SCREENS
Elite Spectrum/Vmax2Series
Ver. 1.1
Users Guide
Elite Screens Inc.
[e-mail] / www.elitescreens.com
Rev. 1.1

E
l
it
e
SCREENS
VMAX2 & Spectrum Series
IMPOR TAN T S AFETY IN STRU CTIONS
1. Position the power cord so it will not be; near any heat source, or ina position to be pulled on or
tripped over.
2. To avoid suffering an electric shock, do not attempt to disassemble this appliance by yourself.
3. In the event of technical trouble, please contact Elite Screens’ service dept. for help with any
technical troubleshooting or warranty claim.
4. Please disconnect the power supply when the screen will not be in use for a prolonged period of
time. This is good general advice for any electric hardware.
Important:
To avoid possible injury and/or an electric shock, do not attempt to use the screen if there is
obvious damage or the presence of broken parts.
PRE-INST
A
LL
A
TION
1. Carefully unpack the screen.
2. Always handle the screen in a leveled position on a clean surface.
3. In order t o protect the screen from exposure to stains and other impurities, keep the screen out of contact wi
t
foreign particles such as dirt, sawdust and liquids.
Keyhole forflush mounting to
Walls (R5MM, R2MM)
Top keyholes for ceiling
mounting (R3MM, R2MM)
3-5/8” Height
of end cap
3-1
/
8”Widthof
End cap
4”
3-3
/
4”
①
Elite Screens Inc.
[e-mail] / www.elitescreens.com

E
l
it
e
SCREENS
1. Select the location for your screen so that it has access to a good power source as well as a
functioning angle and throw distance for your projector.
2. For the best installation results, it is ideal to secure your screen into the studs of your house's
internal wooden framework. If studs are not available in your preferred point of installation, use
the hollow wall anchors for mounting your wall-screws into the drywall. If you are installing into
a concrete structure, use the concrete bolts for securing your screen into the walls. ( Note*
Always consult a professional installer or hardware store specialist for the correct
screws and bolts)
3. Make sure that the screen is perfectly level. Always use a leveling tool to ensure that the
screen runs in perfect alignment with its center of gravity.
4. Position the washers at the head of the wall-screw. The washers give added stability and
ensure that the casing is firmly anchored to the wall.
5. The screen casing is designed to accept the wall screws directly. If not using the optional L-
brackets, be sure to position the washer between the head of the wall-screw and the anchor
slots on the projector casing.
Regardless ofmounting method,screens should be securelysupported so that vibration
or even abusive pulling on the viewing surface will not cause case to work looseorfall.
Installersmust insure that the fastenersused are of adequate strength and suitablefor
the mounting surface chosen.
②

E
l
it
e
SCREENS
1. Using a tape measure, mark the keyholes that are located at the back of the screen's
casing end cap. 2. After marking the area and drilling the holes, insert the screw and
leave about 1/8” ofan inchfrom the wall tomount the screen. (Fig. 1)
Fi
g
. 1
Optional installation using achain and D-rings to hang the screen from theceiling.
Fig. 2
1. You can also hang the screen from the ceiling by using a chain with s-hooks through
the end cap D-rings (not included) suspended by the two loops located on each end of
the case as shown on(Fig. 2).
③
Elite Screens Inc.
[e-mail] / www.elitescreens.com
*Each screen has a basic
installation kit which
includes a bubble level to
assist with your installation

E
l
it
e
SCREENS
Wood/Dry Wall installation: Use wood
screws (B) or use hollow wall anchors (E)
provided with the installation kit as shown
on Fig.1
Top view o
f
L-bracket
Fi
g
. 1
Fi
g
. 2
Masonry/ Cement wall
installation: Use “D” bolts
provided for installing your
bracket
*Once the L-brackets are in place, the screen can be hung from the vertical hooks.
Please note that these are only example illustrations and additional hardware may be
required for your particular installation. Al so, the screen is generally hung directly on the
wall screw s or bolts without using the optional L-brackets.
Elite Screens Inc.
[e-mail] / www.elitescreens.com
④
VMAX2/Spectrum optional accessories; The L-Brackets for Wall & Ceiling
Installation and 12-Volt Trigger for Synchronized Projector-Screen Operation
L-Brackets

E
l
it
e
SCREENS
To Projecto
r
Orange DC12V
Green
0V
V
ideo Projection Interface
12-Volt Trigger Assembly
Connection
pins
are
inside the case
Wall-mounted Receiver
(Hard-Wire Control)
Diagram A
Wall Box with IR Remote
Diagram B
Infrared “Eye” Sensor with
IR Remote
2. Below is the RF remote with a range of 30 Ft. 3. Below is the IR remote (Infra
r
ed) with a
range of 15 Ft.
(Radio Frequency)
Note: When you get the optional RF, you
should follow the instruction and adjust the
code.
(Infra Red)
Note: The light on this remote does not turn on
when the buttons are depressed unlike the RF
⑤
Elite Screens Inc.
[e-mail] / www.elitescreens.com
12-V Trigger
The VMAX2 and Spectrum Screens have the capability of using a 12-Volt Trigger. However, this accessory is
standard only for the VMAX2, optional for Spectrum models.

E
l
it
e
SCREENS
Note:
If theelectric screen does not move,
p
lease chec
k
the followin
g
:
1. Check the power supply and fuse first. The screen will not move without power.
2. Make sure the power cord is plugged to the power outlet.
3. Check all cable connections to see any are disconnected.
4. If the screen works well with the line switch but not with the remote control, make sure that the
remote has good batteries in it.
F
A
Q's
1. Q: How is the Matte White or High Contrast screen material cleaned?
A: The Matte White or Elite High Contrast screen material can be cleaned with mild soap
and water.
2. Q: What type of batteries do the remote controls require?
A:The IR and RFremote controls useAAAalkalinebatteries
3. Q: Can you manually pull down the screen?
A: Absolutely not, manually pulling down the screen will damage the electronic motor rolling
system.
4. Q: Can the electric screen be used in 220-volt outlets?
A: No, the screen can only be used in 110-volt outlets (common household outlet). The
220volt outlets are for industrial tools and machinery.
5. Q: What is the gain on the matte whitescreen material?
A:The matte whitematerial has again of 1.1.
Note: Fo
r
more U
p
date F
A
Q,
p
leasevisit www.elitescreens.com
Elite Screens Inc.
[e-mail] / www.elitescreens.com
⑥

E
l
it
e
SCREENS
Two (2) yearwarranty parts and labor from purchase date as follows (except for
refurbished units as specified below):
•Refurbishedunits carry a 90-day parts andlabor warranty.
•Demo units or open box items areAS IS items anddo not carry a warranty.
•Each party will be responsible for oneway shipping during the warrantyperiod.
An RMA (Return Merchandise Authorization) number must be issued in order to
process a replacement. Elite Screens will replace the DOA (Defective On Arrival) unit
with a brand new replacement *(see exceptions below) after the DOAunit is received
and confirmed defective. Elite Screens will send out a *new unit to the customer by
ground service (subject to inventory availability). Should a problem be reported
after the 7-day grace period, the item must be shipped tous for warrantyrepair.
•DOA(Defective OnArrival): Must be reported within 7 business days of delivery..
Missing Parts must be reported within the 7-day (DOA) grace period. If reported
after 7 days, customer will be only responsible for shipping and handlingfees. If
reported after 30 days of receipt, customer is responsible for cost of the parts and
shipping & handling fees.
Pleasevisit lin
k
below fo
r
full warranty information
http://www.elitescreens.com/services.html
Pleasevisit lin
k
below fo
r
warranty claim
http://www.elitescreens.com/help.html
*
A
new o
r
refurbished replacement will besent out to the custome
r
depending on the
type of purchase (new or refurbished) or based on stockavailability.
⑦
Elite Screens Inc.
[e-mail] / www.elitescreens.com

E
l
it
e
SCREENS
T
wo wa
y
s to re
g
ister
y
our warrant
y
with Elite Screens Inc.
A. On Line
(
Faste
r
and Easier
)
www.elitescreens.com/re
g
iste
r
.html
B. Fill out & Fax to
(
562
)
483-8498,Attn: Custome
r
Service De
p
t.
*
Y
ou
r
Name:
_
_
___
Address:
_
_
Cit
y
/State/Zip __
*EmailAddress:
_
_
*Phone:
_
_
*Screen Model: _ _
*Serial Number:
_
_
*Date of Purchase: ____ _
*Deale
r
/
Reselle
r
Purchased from
(
name of the reseller
)
:
__
_
What is
y
ou
r
Pro
j
ecto
r
Model :
_
_
Application: ___ Home ___ Education ____ Business _ Government___ Othe
r
How would
y
ou rate this screen? ___ Excellent ___ Good ___ Ok ___ Improvement needed
Comments:
I
f
you have pictures o
f
your screen you'd like to share with us, please email your pictures to:
[e-mail]
Or call us at 877-511-1211 EXT 203 or EXT233
For any technical inquiries, please email to
[e-mail] or 877-511-1211 ext 202
For any warranty claim inquires, please email to
[email protected]or 877-511-1211 ext 203
Elite Screens Inc.
[e-mail] / www.elitescreens.com