Elite Screens Kestrel Home Series User manual

02092015 EA www.elitescreens.com/kestrelhome 1
Kestrel Home Series
Electric Floor Rising Projection Screen
USER’S GUIDE
IMPORTANT SAFETY NOTES
1. Please read this manual before use and follow the procedures specified:
a. Please retain this manual for future reference.
b. To avoid any damages to the screen, do not use any accessories or parts
not recommended by Elite Screens.
c. Handle the device carefully during transportation.
d. Do not set up screen on uneven surfaces.
e. To prevent electrical shock or fire; never overload the power cord, and
avoid contacting the motorized components with liquids or foreign objects.
2. The tubular motor equipped in the Kestrel Home series features an overheat
protection sensor. If the screen is consecutively brought up and down between 3-4
minutes, the motor will automatically shut-off to prevent the motor from sustaining
damage through overheating. If the automatic shutoff is activated, please allow 30
minutes cool down before resuming operation.
3. The Kestrel Home Series is equipped with a strong tension cross-spring system.
Please do not attempt any unnecessary repairs. It is at your own risk to open the inside
cover or dismantle/work on the screen. Individual modifications to this product are
prohibited and will void the user’s warranty.
4. When using the screen, please
a. Avoid strong wind, rain, or electrical storms.
b. No direct sunshine (UV Radiation) or moisture.
c. Keep away from fire sources and high temperature devices.
d. Turn off the power before moving this product.
Keep away from children
Keep hands clear from the closing panels

02092015 EA www.elitescreens.com/kestrelhome 2
NOTE:
This equipment has been tested and found to comply with the limits for a Class B
digital device pursuant to Part 15 of the FCC Guidelines.
The products are designed to provide reasonable protection against harmful
interference in a residential/commercial installation and end user application and
may radiate radio frequency energy.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
1. The power outlet should be close to the unit and easily accessible.
2. Re-orient or relocate the receiving antenna.
3. Increase the separation between the equipment and the receiver.
4. Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
5. Consult the dealer or an experienced radio/TV technician for additional help.
Kestrel Home Standard Accessory
Kestrel
Optional Accessories
Available for purchase at www.shop.elitescreens.com or your preferred reseller
Qty 2
AA Batteries
Radio Frequency
Remote Control
Part# - ZSP-RF-B
Low Voltage 3-way
Wall Switch
Part# - ZSP-WB-B
Wireless 5-12V Trigger
Part# -ZSP-TR02

02092015 EA www.elitescreens.com/kestrelhome 3
SCREEN OPERATION
Setup: Remove the controls and wiring from the compartment on the left side of the Kestrel
Home Floor Electric Screen as shown in the pictures below.
Connect the screen to the power supply and switch the power button on. Now it is
ready for use.
Power:
About the Control System:
1.
Wireless 5-12V Trigger: Awireless RF 5-12 volt trigger (Part #: ZSP-TR02) is included
with your new Elite Kestrel Home. This trigger allows you to synchronize the screen’s rise and
drop with the projectors power cycle. The screen rises when the projector powers up and
retracts when the projector powers down. To enable this feature, connect one end the 5-12V
trigger cable to your projector’s trigger output port and the other end to the RF remote
control(see diagram below). The trigger feature will not work without if the projector does not
have a 5-12V output port. If you encounter any issues please visit the “Downloads” section for
the Kestrel Home Series at: www.elitescreens.com/kestrelhome
2. RF (Radio Frequency): The Kestrel Series screen includes an RF remote control. The
standard RF remote is the best option to use as it does not require a direct line of sight.
ON OFF

02092015 EA www.elitescreens.com/kestrelhome 4
Controlling the Kestrel Series with 3-way wall box switch (not included):
The following accessories are not included with your Kestrel Home screen but can be
purchases separately. Keep this information in a safe place should you decide to obtain
these accessories in the future.
1. 3-way wall switch box: The 3-way wall switch box allows manual control to operate the
screen’s UP/STOP/DOWN commands.
The RJ-45 input jack is located on the left side compartment which accepts the 5-12V trigger,
extended IR “eye” receiver or the 3-way wall switch box.
Storing the screen:Always store the screen flat horizontally. Never store the screen in
a vertical position.
Screen Maintenance
1. Always close the screen when not in use
2. Do not touch the screen surface
3. Keep away from direct sun and high/low temperatures
4. For indoor use only
5. Clean with soft water
6. Do not drop/close screen consecutively for more than 3 minutes. This is to avoid
overload protection shut-off. If automatic shut-off occurs, please wait for 20-30 minutes to
try again.
Please visit www.elitescreens.com should you need to contact us for technical support or
service.