Elite Screens Edge Frame User manual

Edge Frame Projection Screen
User’s Guide
Rev.10252019MZ 1 www.elitescreens.eu
Thank you for your purchase of an Elite Screens edge frame projection screen.
Hardware and Parts List
Please make sure all parts listed below are included before installation.
A. Elbow joint x4 pcs
B. Top/Bottom horizontal fame x4 pcs
C. Left/Right vertical frame x2 pcs
D. Center joints x2 pcs
E. Center Support bar x1-2 pcs
F. Wall brackets x2-3 pcs
(135”-150”x2pcs)
G. M5x15 screw x24 pcs
H. M5x50 screws and anchor x6 pcs
I. Rubber hammer x1 pc
J. Screwdriver x1 pc
K. Black Tape x1 bag
L. Bezel trim x6 pcs
M. Corner sleeve x4 pcs

Edge Frame Projection Screen
User’s Guide
Rev.10252019MZ 2 www.elitescreens.eu
Frame Assembly
1. Insert the center joint into one of the ½ horizontal frames (B) and fasten it with the two M5x15
screws (G).
2. Insert the other ½ horizontal frame piece to the center joint and fasten also using two M5x15 screws.
3. Repeat steps 1 and 2 for assembling the second horizontal frame.
Push
4. Insert the elbow joint (A) into each end of the horizontal frames (B) as shown below.
5. Insert the two vertical short frames (C) into the elbow joint (A).
Horizontal long frame (B)
Elbow Joint (A)
Elbow Joint (A)
Horizontal frame
Center Joints
Top right Frame
Top left Frame
Push

Edge Frame Projection Screen
User’s Guide
Rev.10252019MZ 3 www.elitescreens.eu
6. Join the remaining horizontal long frame (B) with the frame built in the previous steps as shown
below.
Horizontal long frame (B)
Vertical short frame (C)
Horizontal Long frame (B)
push
push
push
push

Edge Frame Projection Screen
User’s Guide
Rev.10252019MZ 4 www.elitescreens.eu
7. Make sure all four corners are properly in place to form a perfect square. Then fasten the four
angles with the M5x15 Screws (G).
Screen Material Installation
1. Lay the screen material completely flat with the front facing down on a clean surface in a horizontal
position. The back side of the screen material should be placed upwards.
Note: The back side of the material has the velcro borders all around the edges.
2. Carefully and gently place the assembled frame on top the screen material as shown below. Make sure
to not allow the angle edge of the frame to come in direct contact with the screen material to avoid
puncturing it.
Four corners join correctly to form a
perfect square. Use the included
screwdriver (J)to fasten the M5x15
screws (G) into each corner by aligning
the frame screw holes to the holes in the
elbow joint (A).
Screen material back facing up
Screen material comer

Edge Frame Projection Screen
User’s Guide
Rev.10252019MZ 5 www.elitescreens.eu
3. After all of the corners of the frame have been properly aligned, attach the material to the frame in the
following order A→B→C→D (see instructions below for details).
Attach the screen material to the corners as shown below.
4. After all four corners have been attached; please check whether the frame corners are wrapped by the
screen material. If not, please loosen the velcro connection and repeat the above steps so the frame is
not exposed.
Note: The black shaded part represents the velcro on the frame. That Velcro
end will ultimately attach with the other velcro end on the screen material.
Note:
Represents
the screen
material
2) Fold over and attach
material to the velcro
strip of the frame.
3) Fold over second side
and attach to frame
4) Repeat until all four
sides are done in the
order A, B, C, D
1) Stretch the screen
material in the direction
of the arrowhead.
A
C
A
B
D

Edge Frame Projection Screen
User’s Guide
Rev.10252019MZ 6 www.elitescreens.eu
5. Proceed to attach the rest of the material to the frame as described in the illustrations below.
6. If the material is too loose or tight after adjusting all four corner sides, then you will need to reattach the
material.
Please follow the steps below to properly remove the screen material from the frame. This procedure
will ensure prolonging the life of the screen material.
Lay the Velcro end on the screen
material over the Velcro end of the
frame and keep it within the edge.
Proceed in the following sequence
below ①②
The key is to attach within the
middle sections of 1 and 2. Then
continue attaching the remaining
unattached areas.
Repeat the same steps on
remaining three sides in the
sequence A, B, C, and then D as
show below.
Grasp the middle of the screen
material and attach it to the velcro
strip on the frame
Attach in the following sequence: a-b-c-d
B
A
C
D

Edge Frame Projection Screen
User’s Guide
Rev.10252019MZ 7 www.elitescreens.eu
Screen Material Removal
1. Detach the velcro from the frame.
2. Gently pull back the material to release it from the velcro connections on the corners
Support bar installation (for models under 135”):
1. Position the center support bar (E) in the middle of the frame and align the hole on each end of the
support bar with the M6 hex screws on the top and bottom frames. Then fasten with the M6x12
screws.
Move the M6 hex screw to the middle area of the
frames.
Align the M6 screws
with the two holes.
Pull back the screen material from
the velcro connection along the
edges of the frame to detach it.
Center Support bar

Edge Frame Projection Screen
User’s Guide
Rev.10252019MZ 8 www.elitescreens.eu
Support bar installation (for models 135”- 150"):
1. Position the center support bar (E) and M6 hex screws in the areas of the frame shown in fig 1. (Each
about one thirds the way in from the end of the frame.) Align the hole on each end of the support bar
with the M6 hex screws located at the top and bottom frame sections. Then fasten with the M6x12
screws.
Notice to Installer:
Please use the following installation instructions to obtain superior optical performance from the
Angular Reflective ALR (Ambient Light Rejecting) Screen.
Make sure to follow these instructions in order for the DayWalker screen fabric to perform correctly.
•Angular-Reflective material is not compatible with ultra/short-throw projectors
•Minimum lens throw ratio 1.5x image width
•Ambient light must not come from the same direction as the projector
Center Support Bar
Align the M6 Screws with
the two holes located on the
Center Support Bar.
Figure 1
Move the M6 hex screw to these areas of the frame.

Edge Frame Projection Screen
User’s Guide
Rev.10252019MZ 9 www.elitescreens.eu
Since angular-reflective means that the projected image will reflect at the mirror-
opposite angle, it is important to position the projector so that the viewer will get the best
possible image.
Step 1: Establish the general “eye level” of the viewers
Step 2: Set the appropriate projection level
Step 3: Adjust the screen height level and projection angle
Input Angle (A) = Output Angle (B) aligns with the viewer’s angle

Edge Frame Projection Screen
User’s Guide
Rev.10252019MZ 10 www.elitescreens.eu
Edge trim Installation
Included is an ultra-thin black edge trim that provides an elegant bezel finish
1. Place the assembled frame on a flat and clean surface. The projection screen surface should be facing
up.
a. As an option, Black Tape is supplied to cover any possible gaps between the pieces of the bezel
trim. Align the tape with the edge of the screen, as shown in Figure 1. Once properly aligned,
apply the black tape to the center of the top and bottom of the screen material.
Figure 1
2. Without removing the adhesive tape, place all the trim pieces along the edge of screen material. Adjust
the trim so that the top and bottom trim pieces are touching and show no gaps in the center. (Note: The
Elite logo should be positioned on the bottom right). Refer to Figure 2 below for a visual reference.
NOTE: Make sure the bottom edge trim with the Elite Screens logo is installed on the correct side. The
back of the material should be labeled with a DOWN sticker to indicate the material is facing in the down
position. The Elite Screens logo should be installed on the DOWN side
Edge trim x 6 pcs
Black tape x1pcs
Trim
strip
Screen Material
The black
tape
Front Side
Back Side
Plastic corner sleeve x4pcs
The black tape
Figure 2
TIP:
Align the trim
starting from the
center to reduce
gapping. Any gaps
left at the corners
will be covered by
the corner sleeves.
White area
signifies
corner gap.
Figure 1