Elite Screens QuickStand Series User manual

Rev043010-JA
www.elitescreenscom [e-mail]
QuickStand Series
Portable Frame-Folding Projection Screen
User’s Guide

Rev043010-JA
www.elitescreenscom [e-mail]
Setup Procedure
The frame and supports are made of 1 3/8” aluminum tubing with an anodized finish. Please follow the
instructions in this package. With proper care, your QuickStand screen will provide many years of reliable
service.
fig 2
Top
fig 1
fig 3
Lock down the corners
Snap latch
Snap latch
Top
Two Section Frame
(For presentation screens that are less than 120” in diagonal
measurement)
1. Take the frame out of the case and remove its wrappings.
Unfold the main joints as shown in (fig 1).
2. Once the main joints are unfolded, make sure that the snap
latches “click” into the locked position. The frame should now
be fully elongated as in (fig2). *Note: The snap latches will
automatically lock when the joint is straightened. Press the
snap latch button in order to release the lock.
3. While holding the bottom of the frame in place, lift the top of
the frame to unfold the sides which will cause the snap latches
lock when fully extended. Secure the corner braces into the
locked position. The screen frame should now be fully opened
as in (fig 3).

Rev043010-JA
www.elitescreenscom [e-mail]
Three Section Frame
(For large presentation screens that are 120” or more in diagonal
measurement)
1. Take the frame out of the case and remove its
wrappings. Unfold the main joints making sure that
both the end and middle spans are in prefect alignment
as shown in (fig 4).
2. Make sure that the snap latches have locked the joints in
the frame so that it is at its full horizontal extension as
shown in (fig 5)
3. While holding the bottom of the frame in place, lift the
top of the frame to unfold the sides which will cause the
snap latches lock when fully extended. Secure the
corner braces into the locked position. The screen frame
should now be fully opened as in (fig 6).
fig 6
Lock down the corners
Snap latch
Snap latch
Top
fig 4

Rev043010-JA
www.elitescreenscom [e-mail]
fig 7
Standard T-Leg Support
1. Take the T-Leg out of the case and remove its wrappings.
Fold down the support legs as shown in (fig 7).
2. Secure the corner braces into the locked position as
shown in (fig 8)
3. Unfold the T-Leg’s main support until the snap latches
“click” into the locked position as in (fig 9).
fig 8
Lock down the corners
fig 9
Snap latch

Rev043010-JA
www.elitescreenscom [e-mail]
locking bolt
frame spacer
fig 12
fig 10
AT-Leg (optional support buttress recommended for the large
screens with diagonal measurements of 150” and over)
1. Take the AT-Leg buttress out of the case and remove its wrappings. Unfold the buttress as shown in (fig 10).
2. Snap latches will automatically lock in the center joint. Use the snap latch buttons to unlock the end joints as
shown in (fig 11).
3. Attach the AT-leg to the T-Leg by securing the locking bolts through the frame using the frame spacers
between the metal parts as shown in (fig 12) (*Note: It is important to always use the plastic frame spacers
between the pieces whenever connecting any of the aluminum surfaces such as T-bars to AT, SAT and Frame
components.)
fig 11
Snap latch

Rev043010-JA
www.elitescreenscom [e-mail]
locking bolt
frame spacer
fig 15
SAT-Leg (optional added stability buttress recommended for the
large screens with diagonal measurements of 180” and over)
1. Take the SAT-Leg out of the case and remove it wrappings as shown in (fig13).
2. Undo the snap locks to loosen and bend the joints for proper fitting as shown in (fig 14).
3. Attach the SAT-Legs by securing the locking bolts through the frame using the frame spacers between
the metal parts as shown in (fig 15)
fig 13
fig 14

Rev043010-JA
www.elitescreenscom [e-mail]
Folding the Screen material for proper packing
Please observe the following precautions before folding up the screen material.
1. Do not bring the viewing surface into contact with chemical solvents, sharp or abrasive objects,
painted, varnished or plastic finished items.(*See the cleaning instructions for exceptions to this)
2. Make certain that the screen is laid out on a dry, clean and flat surface.
Folding up the screen:
Lay out the screen with the viewing surface facing up and cover it with flat (not crumpled) tissue or packing
paper that is clean and unprinted. *Note: Do not ever use abrasive paper, newspaper or any printed
material on your projection screen.
1. With the viewing surface facing up, fold the fabric in half from top to bottom. When folding, make
certain that the viewing surface does not come into contact with the black binding, grommets or snap
buttons. *Note: The screens are shipped from production with tissue paper in the folds that should be
retained for future use.
Attaching the Frame to its Supports
1. Always use at least two locking bolts through the T-Leg Support, the Spacer and into the Frame on each
side.
2. Height can be adjusted in 8” increments up or down. Normal screen height is 44” from the bottom of the
frame to the floor.
3. Reverse this process to dismantle and pack away the screen.
locking bolt
frame
leg
frame spacer
snap latch button

Rev043010-JA
www.elitescreenscom [e-mail]
2. Make sure that the first folds never exceed 3 feet in width (fold again if necessary). Also make sure
that there is always clean packing paper in between the two surfaces.
3. Larger sized screens will need to be folded with more frequency than smaller screens. Follow the
instructions from step 1 as well.
4. Fold the material from top to bottom first then alternate in folding left to right until the material is of a
sufficient size that will fit into the leatherette case.
Note: Keep the screen material inside its case when not
in use. Failure to follow this precaution may eventually
result in staining or discoloration.
Cleaning
The screen surface can be cleaned as follows.
Use a clean white cloth (100% cotton preferred) and dampen it with clear water. Gently wipe in one direction
and NOT in a circular motion. Use another dry cloth to dry after each cleaning session. To remove a
stubborn stain or sticky surface, use denatured alcohol (methanol or methyl alcohol) in lieu of water.
Attaching the Screen once it is unpacked
1. Using the snap buttons to connect the Screen material with the case
2. Start at the top working in whatever direction is most comfortable to you
3. Stretch the corners if necessary to pair up the buttons with their corresponding snaps

Rev043010-JA
www.elitescreenscom [e-mail]
The following points should be noted to assure the sound performance and longevity of
your screen
1. Never use your hand to touch the screen surface.
2. Never scrabble on the screen with anything.
3. Don't touch the screen with hard or sharp objects.
4. Please use a clean cotton cloth or soft dust brush to remove any dust particles on the screen.
5. The screen material may be cleaned
Warranty Policy
Two (2) year parts and labor warranty from defects in workmanship from purchase date (except for
refurbished units as specified below):
Refurbished units carry a 90-day parts and labor warranty.
Each party will be responsible for one way shipping during regular warranty period. Elite Screens is not
responsible for applicable international tariffs such as broker fees and customs duties.
An RMA (Return Merchandise Authorization) number must be issued in order to process a replacement.
Elite Screens will either replace or repair the defective unit with a brand new replacement *(see exceptions
below) after the defective unit is received and/or confirmed defective. Once the product is received, Elite
Screens will send out a new *unit to the customer by ground service (subject to inventory availability).
Please do not return any unauthorized items to Elite Screens, as they will be refused. The RMA
number must be included on the outside label of your shipping box. Our warehouse is not
authorized to accept returns thout an RMA number on the shipping label. RMA numbers are
valid for 45 days from the date of issue.
Missing Parts must be reported within the 7-days of receipt. If reported after 7 days, customer will only be
responsible for shipping and handling fees. If reported after 30 days of receipt, the customer is responsible
for cost of the parts and shipping & handling fees.
*A new or refurbished replacement will be sent out to the customer depending on the type of purchase (new or
refurbished) and is based on stock availability.
For Warranty and Service requests please fill out a RMA /Service Form at
http://www.elitescreens.com/warrantysupportform
Please Visit this link for full Warranty information:
http://www.elitescreens.com/warranty
Remember to register your Elite Screens product at:
www.elitescreens.com/register
Parts List
1. Frame x 1 piece
2. Support (T) Legs x 2 pieces
3. AT-Legs x 2 pieces (optional depending on size)
4. SAT-Legs x 2 pieces. (optional depending on size)
5. Screen Fabric x 1 piece
6. Locking Bolt x 6-26 pieces
7. Frame Spacer x 6-26 pieces
8. User Guide x 1 pieces
Please make sure all parts listed are supplied. Should any parts be missing contact us
at [e-mail]

Rev043010-JA
www.elitescreenscom [e-mail]
CONTACTS
US & Canada Tech Support & Warranty Claim
Please contact us at [e-mail] or call [phone] #3 Service
Europe Tech Support & Warranty Claim
Please contact us at [e-mail] or call [phone]
Asia Tech Support & Warranty Claim
Please contact us at [e-mail] or call [phone]
Taiwan Tech Support & Warranty Claim
Please contact us at [e-mail] or call [phone]
America:
Elite Screens Inc.
16410 Manning Way
Cerritos, CA 90703 USA
Tel: [phone]
Fax: [phone]
[email protected]
www.elitescreens.com
Asia:
Elite Screens China Corp.
Longxi Duimianling Industry Zone
Longcheng Longgang District,
ShenZhen GuangDong, China
Tel: [phone]
Fax: [phone]
[email protected].cn
www.elitescreens.com.cn
Taiwan:
Elite Screens Taiwan Co. Ltd.
No.38, Alley 22, Lane 66,
Sec. 5, Nanjing E. Rd.,
Songshan District, Taipei City 105,
Taiwan
Tel: [phone]
Fax: [phone]
[email protected].tw
www.elitscreens.com.tw
Europe:
Elite Screens Europe GmbH
Elite Screens Europe GmbH
Lübecker Straße 1
22087 Hamburg, Germany
Tel: [phone]
Fax: [phone]
[email protected]
www.elitescreens.eu
Elite Screens France S.A.S
11, Allée William Penn
92150 Suresnes, France
Tel: [phone]
Fax: [phone]
[e-mail]
www.elitescreens.com/fr
Latin America Contact:
[email protected]om
East Asia Contact:
[email protected]
Japan Contact:
[e-mail]