Elite Screens Aeon CineGrey 4D AT Series User manual

Rev.032722DT (DS0189) www.elitescreens.com 1
Aeon CineGrey 4D AT Series
Ceiling Ambient Light Rejecting Acoustically
Transparent EDGE FREE®Fixed Frame Screen
USER’S GUIDE
E Type - V1
Product Description: The Aeon Series is a fixed frame projection screen that uses Elite’s EDGE FREE® technology.
The EDGE FREE® design resembles a giant size flat panel TV display. The Aeon includes a bezel trim to further
enhance the frame appearance and absorb projector overshoot. An optional LED kit is available for back-lighting.
Congratulations on your new Aeon CineGrey 4D AT purchase! The ISF Certified CineGrey 4D AT is an ambient and
ceiling light rejecting (ALR/CLR®) front projection screen material that is perforated for acoustic transparency. It
is precisely formulated for environments with minimal control over room lighting. It was designed to enhance
picture brightness, offer accurate color fidelity, improve contrast and allow sound to pass through.
Maintenance and Care
In order for the CineGrey 4D AT material to maintain its projection qualities and provide optimum performance
please refer to the list below for proper maintenance and cleaning.
The following precautions should always be followed to avoid damaging the material, which is not covered
under warranty.
• Use a dry microfiber cloth or a soft bristle brush to remove dust from the screen’s surface.
• When cleaning, use a damp microfiber cloth with warm water to remove any marks.
• Never rub or apply pressure when cleaning the surface.
• Never attempt to use any chemicals such as acetone, benzene, alcohol, organic solvents or abrasive
cleaners to clean the screen surface.
• To avoid damaging the screen, avoid touching it directly with your fingers, pens/pencils or any other sharp
or abrasive objects.

Rev.032722DT (DS0189) www.elitescreens.com 2
Make sure all parts are included before commencing frame assembly.
Hardware and Parts List
①Edge Trim A
⑦Long Center Joints b
⑬Elbow Joints a
⑲Support bar
②Frame A
⑧Short Center Joints
⑭Elbow Joints b
⑳Spring a
③Wall Bracket
⑨M4x4 Screws
⑮Elbow Joints C
Spring b
④Anchor
⑩M5x6 Screws
⑯Corner Cover
Fiberglass rod
⑤Wood Screws
⑪Edge Trim B
⑰Frame C
Screen material
⑥Long Center Joints a
⑫Frame B
⑱Edge Trim C
23
22
21
Exploded View of Aeon Frame

Rev.032722DT (DS0189) www.elitescreens.com 3
SCREEN INSTALLATION
⑫
frame B
⑰
Frame C
⑫
frame B
②
Frame A
②
Frame A
⑰
Frame C
1.
⑥Long Center Joints a
⑦Long Center Joints b
⑩M5x6 Screws
⑩
M5x6 Screws
⑭Elbow Joints b
⑬Elbow
Joints a
2.
Note: the support bar is mounted in the upper and lower
border splicing direction as shown on the right
1. Loosen the screwon the
support bar (the connecting
piece can slide).
2. Adjust the connector to
align its hole position with
the border hole position.
3. Fix with ⑨ M4X4 screws.
Frame
M4x4
screws
Support
bar
1. Frame Assembly
2. Center Support Bar Installation

Rev.032722DT (DS0189) www.elitescreens.com 4
1. Lay the frame front face up on a flat surface.
Note: Velcro installed on edge of frame.
2. Begin attaching the black backing on the four corners to the velcro on the frame and press firmly to make it
more compact. Lift and remove to smooth out and avoid wrinkles.
Note: Assure the four edges of the black backing cloth do not go beyond the space of the velcro.
Black backing dimensions
Screen size
Height
Width
110”
52.9”/1345 mm
94.8”/2410 mm
125”
60.3”/1532 mm
107.9”/2742 mm
135”
65.2”/1656 mm
116.7”/2964 mm
150”
72.5/1843 mm
129.7”/3296 mm
3. Black Backing Cloth Installation

Rev.032722DT (DS0189) www.elitescreens.com 5
3. Re-attach black backing cloth from center to corner and pull the black backing cloth to fit the velcro to make
it more compact again. Then finish to attaching the black backing to the velcro.
Unrolling the screen material
Two people recommended
1. Put on the supplied pair of white gloves.
This is to avoid leaving oily handprints on the
screen surface which are not removable.
2. Remove the screen material from the tube and
place a small suitable weighted object at the end
of the material.
3. Lay the material face down, two people
carefully lift the rolled end and slowly rotate the
material clockwise.
4. Insert the corresponding fiberglass rods through the sleeves on the edges of the material as shown below.
Back side of screen material
Weighted
object
Back side of screen
Note: Backside facing up
(frontside facing down)
Front side of screen
Clean surface area
ATTENTION: Put the gloves on when handling the screen material to avoid touching it with your bare hands.
4. Screen Material Installation
Fiberglass rod
a1 = a2 ≒35mm
Backside of screen
22

Rev.032722DT (DS0189) www.elitescreens.com 6
Spring Attachment Method
First hook one end of the spring in the frame slot, then hold the screen around the frame to pull, and finally use the
spring hook to pull the spring hook in the screen hole.
1. Connect Edge Trims A&B to form the top/bottom trims with the ⑧Short Center joints, and then
insert them on the top/bottom frames.
2. Connect the side edge trims C with the top/bottom edge trim with ⑮Elbow Joints C.
3. Adjust the trim so that the top and bottom trim pieces are touching and show no gaps on the corners.
Then fasten them with the ⑨M4 x 4 screws.
1 . Carefully and gently place the assembled frame on
top of the screen material.
DO NOT allow the angle edge of the frame to come in
direct contact with the material to avoid puncturing it.
2. Adjustthedistancebetweentheedgeofthe frame and
the material (a1 = a2) to 1.4”/35 mm
Backside of screen
a1=a2
a2
Backside of screen
a1
3. Begin by simultaneously attaching three springs in
the center of the side frames (C→D) and repeat for
top/bottom frames (A→B).
4. Then, simultaneously attach the springs from the
center to all corners. (Leaving only the four corners.
5. Finally, attach the springs at the four corners
(E→F→G→H).
Backside of screen
5. Bezel Trim Frame Assembly/Installation
Center
connection
⑧Short Center
Joints
⑮ Elbow Joints C
Corner
connection

Rev.032722DT (DS0189) www.elitescreens.com 7
4. Attach a spring b in the middle of each edge trim (1-6) to the frame as shown in the illustration.
5. Install the ⑯corner covers on the four corners of the edge trim.
*Tolerance may be ±1”
Screen size
A
B
C
D
110"
96.7” / 2456 mm
95.9” / 2436 mm
54.7” / 1391 mm
53.9” / 1371 mm
125"
109.7” / 2788 mm
108.9” / 2768 mm
62.1” / 1578 mm
61.3” / 1558 mm
135"
118.5” / 3010 mm
117.7” / 2990 mm
67” / 1702 mm
66.2” / 1682 mm
150"
131.5” / 3342 mm
130.7” / 3322 mm
74.3” / 1889 mm
73.5” / 1869 mm
1
2
5
6
4
3
Edge Trim
Spring b
21
⑯ Corner cover
Front side
Note: Lock front
side first then
back side
Back side
Installation of Corner Cover
2
1
Note: The listed measurements are for general reference only.
D Viewable Height
C Total Height
Border Thickness
28.2mm (1.1”)
A Total Width
B Viewable Width
Bezel Width = 10mm (.39”)
6.Product Dimensions

Rev.032722DT (DS0189) www.elitescreens.com 8
Drill a hole on the wall according to the distance on the chart below distance for your screen. Place the bracket on
the holes and secure them using a Phillips screwdriver. If not installing into a structural wood stud, use a wall
anchor, then screw in the M5x50 screws. Make sure the brackets are leveled.
Hanging the screen:
1. Two people hold the screen and align it first with the bottom bracket. The bracket lip must be inserted in the
frame’s channel per example below.
2. Then pull up the screen on the top bracket and adjust the screen left to right as needed.
For an Elite Screens contact and technical support in your area,
please visit www.elitescreens.com
Screen size
110"
125"
135"
150"
L = Left/Right hole distance
59” /1500 mm
78.7” / 2000 mm
78.7” / 2000 mm
98.4” / 2500 mm
H = Top/Bottom hole distance
47.5” / 1209 mm
54.9” / 1395 mm
59.8” / 1519 mm
67.1” / 1706 mm
7. Wall installation
H
⑤Wood screws
④Anchor
③Top Bracket
⑤Wood screws
④Anchor
③Bottom Bracket
②
①
Frame installed on
top bracket
1
Do not fasten the
screws on the
bottom bracket to
allow screen to
move up and down.
Frame installed on
bottom bracket