Elite Screens TE200HR2 User manual

Rev.053117 DR 1 www.elitescreens.com
Electric Motorized Tab-Tensioned Rear Projection Screen
CineTension Plus Series
User’s Guide
Important Safety & Warning Precautions
Make sure to read this user’s guide and follow the procedures below.
Caution: The screen’s Black Top Drop is already set to its maximum drop distance. There is NO extra
Black Top Drop in the roller. Please be aware of this as it will void your warranty with Elite Screens.
Unapproved changes or modifications (except for cutting the power cord for hardwire installations) to this
unit are prohibited and will void your warranty. For more information, please contact our Technical Support
Department at [phone] Ext. 604.
•Please retain this user’s guide for future reference.
•To avoid damaging the unit, do not use with any unauthorized accessories not recommended by the
manufacturer.
•Handle the unit carefully during transportation to avoid any damages.
•To ensure safe and reliable operation, direct connection to a properly grounded power source is
advised.
•The power outlet supplying power to the unit should be close to the unit and easily accessible.
•Do not install the unit on uneven or inclined surfaces.
•Do not put heavy objects on the power cord and position it properly to avoid creating a trip
obstacle.
•Never overload the power cord to prevent an electric shock or fire due to a loose contact or a short
circuit.
•There are not user serviceable parts in this unit. Do not attempt to disassemble this unit by yourself.
No one except authorized technicians can open and make repairs to this unit.
•Make sure the power source this unit is connected to has a continuous power flow.
•If there is need to use an extension cord, make sure the cord has an equal rating as the appliance to
avoid overheat.
•Do not handle the power plug when your hands are wet or your feet are in contact with water.
Do not use this unit under the following circumstances.
•Disconnect the power cord under the conditions of heavy rain, wind, thunder or lightning.
•Avoid direct Sunshine, rain shower and moisture.
•Keep away from fire sources and high temperature to prevent this device from overheating.
•Cut off the power supply first before transportation or maintenance.
•Fully disconnect from the power supply when the unit is not in use for a long period of time, as
should be done with any other electric household appliance.
•To avoid possible injury and/or an electric shock, do not attempt to use the screen if there is
obvious damage or if there are any evident broken parts.

Rev.053117 DR 2 www.elitescreens.com
WARNING
The Screen’s Top Black Drop is already set to its maximum drop distance. There is NO extra top black
drop in the roller. Please be aware of this as it will void the limitation of your warranty.
Individual modifications to this product are prohibited and will void the warranty with the manufacturer.
Please contact Elite Screens Customer Service for any questions.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur on a particular installation. If this
equipment causes harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures.
Reorient or relocate the receiving antenna of the device which may be causing the
interference.
Increase the separation between the screen and the device’s receiver.
Connect the equipment into a different power outlet other than the device.
Pre-Installation
1. Carefully unpack the screen.
2. Always handle the screen in a leveled position on a clean surface.
3. In order to protect the screen from exposure to stains, keep the screen out of contact with foreign
particles such as dust, sawdust, and/or liquids.
NOTE
Regardless of the mounting method, the screen should be securely supported so that the vibration or
pulling on the viewing surface will not cause the casing to become loose or fall. The installer must insure
that the fasteners used are of adequate strength and suitable for the installation location.
Hardware Parts List
Please make sure all parts listed below are included before proceeding with the installation.
A.M10*Suspended Hook x 4 pcs
B. 20cm*Bubble leveler x1pc

Rev.053117 DR 3 www.elitescreens.com
A
L
M
Clockwise
rotation
L
A
A
B
C.
D.
Installation Instructions
Recessed Installation
1. Select the installation location for your screen. Measure the distances between each eye bolt (Shown as
measurements L and A in Fig.1). Mark the installation area on the ceiling based on the measurements
taken. Using the marks as a guideline, drill a hole in the ceiling for each suspension bolt. The distance
between the installation hole (M) and the wall should be no longer than the measurement A. Insert one
eye bolt of the M10 Suspended hooks into the predrilled holes.
2. Connect the center component of the M10 Suspended hooks to the eye bolts installed above the ceiling.
Once properly secure, connect the third component of the M10 Suspended hooks. Attach the suspended
hooks(4xM10) individually to each of the 4 eye bolts located on the top of the screen (A/B/C/D) .
3. After the installation is complete, if the screen is not leveled, you can adjust the height of the suspended
hooks to level the screen. Below are the adjustment methods for the suspended hooks.The maximum
and minimum adjustable lengths are shown in Fig 3.
①②③④
Hole
（
Fig.3
）
（
Fig.1
）
Ceiling
Wall
Suspended hook
1
2
3
Counter-
clockwise
rotation
（
Fig.2
）
The Screen

Rev.053117 DR 4 www.elitescreens.com
CineTension Plus Series | Controls and Accessories
A. IR Remote
B. RF Remote
C. Wall switch control box
D. 5-12 volt trigger cable
E. IR extended “eye” receiver
F. Wireless 5-12v trigger cable
G. AAA batteries
Screen operation
Electric Current: Depending upon region, your Elite Screen will operate on 110v, or 220v voltage.
1. After ensuring the power outlet & screen are compatible (voltage), plug the power cord into the power outlet.
2. Once the screen’s has power, you’ll be able to control it using any of the 6 methods described below.
6 ways to control your CineTension Plus
1. IR remote control (Item A, Fig 1) and IR “Eye” Receiver (Item E, Fig 2):
The Infrared functions by direct line of sight contact with a beam range of 30
feet. The IR “Eye” receiver plugs directly into the screen’s RJ-45 input to
present a low profile line-of-sight control option for your IR remote control
even in a recessed ceiling installation. Once connected, simply aim the IR
remote at the IR “Eye” receiver to control the screen.
2. RF Remote Control (Item B): The radio waves eliminate the need for a
direct line of sight with a range of 100 feet.
Fig.2
UP
STOP
DOWN
IR “eye” receiver
Fig.1
IR/RF remote
3. 3-Way Wall Switch (Item C, Fig 3): The 3-way wall switch
is a wall mount control box with an up/stop/down button and
plugs directly into the screen’s RJ-45 input.
Fig.3
3 Way Wall Switch
(does not have IR sensor)

Rev.053117 DR 5 www.elitescreens.com
UP
Stop
Down
4. 5-12 volt trigger (Item D, Fig 4):The built-in 5-
12V trigger input allows your screen to synchronize
its drop & rise with the projector’s power cycle.
The screen deploys when the projector powers on
and will retract when the projector powers off. The
5-12 volt RJ45 cable connects to your projector’s
trigger output via a separate cable that may or may
not be provided by the manufacturer of the
projector. The trigger feature will not work without
an output cable from the projector, but it can be
tested by connecting the Red (+) and Green (-)
cable to a 9-volt battery.
5. Wireless 5-12 volt trigger (Item F, Fig 5): The RF remote control serves as a dual purpose, independently as a
handheld remote control, or in conjunction with the Wireless 5-12 volt trigger cable. The radio frequency
technology can be programmed to send a wireless signal to synchronize its drop & rise with the projector’s power
cycle.
Here’s how to set up your Wireless 5-12 volt trigger | Synchronization Instructions
Step1: Connect the wireless 5-12 volt trigger cable to the RF remote (3.5mm)
Step 2: Connect the 12 v adaptor end of the wireless 5-12 volt trigger cable to your projector
Step 3: Make sure to unplug your screen from the power outlet
Step 4: Hold the UP button on your RF remote
Step 5: While holding the UP button, plug the screen back to the power outlet
Step 6: Wait 5 seconds and then release the UP button
Step 7: Your 5-12V wireless trigger should now be activated with your screen and ready to be used and able to
control your screen with your projector’s power cycle
Repeat the steps again if not successful.
(Please be aware, the projector on/off cycle may take longer to fully activate. It usually takes around 20-30
seconds for full off and on cycle each time)
DC 5-12V out
Wireless 5-12V
trigger cable
The back of the
projector
Fig 5
3 prong power cord
RJ45 Input
5-12 volt trigger cable
Fig.4

Rev.053117 DR 6 www.elitescreens.com
Dimensions Table
Model
Number A A1 A2 A3 A4 A5 B B1 B2 B3 B4 B5 C C1 C2 C3 C4
Unit: Inches
TE200HR2 204.0 197.2 192.0 174.3 8.9 196.0 112.3 6.7 4.0 98.1 3.5 105.6 6.7
8.7-
11.2 1.0 0.8 2.6
Unit: mm
TE200HR2 5182 5009 4878 4428 225 4978 2853 170 102 2491 90 2683 170 220-
285 25 20 67
For local EliteProAV contact or Technical Support, please visit
www.eliteproav.com
Note: Data Error: ±1"