Elite Screens Manual Tab-Tension 2 Series User manual

Manual Tab-Tension 2 Series
Tensioned Manual Pull-Down Projector Screen
User’s Guide
Rev. 070119-BR 1 www.elitescreens.com
Thank you for choosing the Manual Tab-Tension 2 Series projection screen!
Please be sure to read the precautions and operating instructions carefully before operating
the screen. Proper maintenance and handling will ensure a longer life-span of the product.
Note:
Wall screws included with this product are complementary and may not be adequate for all mounting
surfaces. Consult with a professional installer or hardware store for proper mounting screws and anchors.
Regardless of the mounting method, the screen should be securely supported so that the vibration or pulling
on the viewing surface will not cause the screen case to become loose or fall. The installer must ensure that
proper mounting hardware and the fasteners used are of adequate strength and suitable for the mounting
surface.
Hardware Parts List
Please make sure all parts listed below are included before proceeding with the installation.
A. Mounting Bracket
B. Eyebolt
C. Dry-wall Anchor and
D. Screw
E. Nut
F. Washer
Item Part List 106” Screen 110” Screen 125” Screen 140” Screen
A
Mounting Bracket
2
2
2
3
B
Eyebolt
2
2
2
3
C
Drywall Anchor
6
6
6
9
D
Screw
6
6
6
9
E
Nut
4
4
4
6
F
Washer
4
4
4
6

Manual Tab-Tension 2 Series
Tensioned Manual Pull-Down Projector Screen
User’s Guide
Rev. 070119-BR 2 www.elitescreens.com
Installation Instructions
For installation assistance, please consult a professional Installer. Elite Screen is not liable for faulty installations.
A. Flush Wall Mount
1. Determine where the screen will be installed. Mark the
screw hole locations, drill the holes and insert the dry-
wall anchor (C).
2. Install the mounting bracket (A) to the wall and secure
with a screw (D).
3. Un-screw the screw on the Bracket, attach the screen
into the Mounting Bracket, then screw the screw to make sure the case slot is securely attached to
the Mounting Bracket.
B. Flush Ceiling Mount
1. Mark the location where the screen is to be installed, drill the holes and insert the Dry-wall
Anchor (C).
2. Install the Mounting Bracket (A) to the ceiling and secure with the Screw (D).
Un-Screw
Attach
Screw

Manual Tab-Tension 2 Series
Tensioned Manual Pull-Down Projector Screen
User’s Guide
Rev. 070119-BR 3 www.elitescreens.com
3. Un-screw the screw on the Bracket, attach the screen into the Mounting Bracket, then screw the
screw to make sure the case slot is securely attached to the Mounting Bracket.
C. Suspended Ceiling Installation (Additional hardware required)
1. Insert the mounting bracket to the screen case. Remove the screw, attach the bracket to the case,
then secure the bracket by screwing in the screw.
2. Attach the Eyebolt (B) onto the Mounting Bracket by using the Nut (E) and Washer (F).
3. Hang the screen onto the ceiling using additional snap link.
Screen Operation
Note: Always pull the screen down or let it up in a 90-degree vertical angle. Do not allow the
screen to touch the screen case when the screen goes up or comes down to avoid damaging the
screen material.
Attach
Un-Screw
Screw

Manual Tab-Tension 2 Series
Tensioned Manual Pull-Down Projector Screen
User’s Guide
Rev. 070119-BR 4 www.elitescreens.com
1. Pull the screen down from the lanyard or from the handle only in a 90-degree angle. Do not
attempt to pull the screen down by the surface or touch the screen, as it will damage the screen and
void the warranty.
Note: An internal auto-lock mechanism system will
cause the screen to stop and lock on the position at
intervals.
2. If you want to the screen to retract back, simply
pull the screen down more than 2 inches and retract
the screen back by quickly and smoothly releasing
it up gently. The screen is equipped with a SLOW
RETRACT MECHANISM (SRM) which allows the
screen to slowly retract without the need to hold on to
the handle or lanyard. Simply release the handle and
the screen will retract by itself.
Note: Always release at a 90-degree angle
and do not let go until the screen is entirely
inside the case
If ever the screen feels stuck, keep in mind
that the screen’s mechanism is new and
needs to be run up/down a few times to loosen
up. If this happens, carefully with a little force
yank the screen straight down to unlock the screen.
Note: Improperly bringing the screen up/down will damage the screen material or rolling system.
RETRACTION TIP: If you are not able to pull the screen down two inches when attempting to
retract it, give the screen a quick yank downwards with a little bit of force. Please be sure to not
stand directly under the housing of the unit when yanking down on the screen.

Manual Tab-Tension 2 Series
Tensioned Manual Pull-Down Projector Screen
User’s Guide
Rev. 070119-BR 5 www.elitescreens.com
Screen Material Tension Adjustment (4mm Allen Wrench required and not included)
Insert your 4mm Allen Wrench to push in the adjustment tension knob, turn clockwise and your screen will
gain more tension. Turn the Allen Wrench counter clockwise and the screen will lose tension. Please note
this adjustment is not necessary as the tension of the screen has been set to its factory setting for best
performance. Please contact Elite Screens for assistance to avoid damaging the screen and voiding your
warranty.
For more information, technical support or your local Elite Screens
contact, please visit www.elitescreens.com